Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes — Amendment 2

Systèmes de canalisations en plastique pour les installations d'eau chaude et froide — Polyéthylène réticulé (PE-X) — Partie 2: Tubes — Amendement 2

General Information

Status
Published
Publication Date
23-Nov-2020
Current Stage
6060 - International Standard published
Start Date
24-Nov-2020
Completion Date
24-Nov-2020
Ref Project

RELATIONS

Buy Standard

Standard
ISO 15875-2:2003/Amd 2:2020
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 15875-2:2003/Amd 2:2020
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO 15875-2:2003/PRF Amd 2:Version 13-okt-2020
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 15875-2
First edition
2003-12-01
AMENDMENT 2
2020-11
Plastics piping systems for hot and
cold water installations — Crosslinked
polyethylene (PE-X) —
Part 2:
Pipes
AMENDMENT 2
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polyéthylène réticulé (PE-X) —
Partie 2: Tubes
AMENDEMENT 2
Reference number
ISO 15875-2:2003/Amd.2:2020(E)
ISO 2020
---------------------- Page: 1 ----------------------
ISO 15875-2:2003/Amd.2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 15875-2:2003/Amd.2:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for

the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in collaboration

with the European Committee for Standardization (CEN) Technical Committee CEN/TC 155, Plastics

piping systems and ducting systems, in accordance with the Agreement on technical cooperation between

ISO and CEN (Vienna Agreement).
A list of all parts in the ISO 15875 series can be found on the ISO website.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/ members .html.
© ISO 2020 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 15875-2:2003/Amd.2:2020(E)
Plastics piping systems for hot and cold water
installations — Crosslinked polyethylene (PE-X) —
Part 2:
Pipes
AMENDMENT 2
Normative references
Replace the reference to "EN 578" with the following:
ISO 7686, Plastics pipes and fittings — Determination of opacity
Replace the reference to "EN 579" with the following:

ISO 10147, Pipes and fittings made of crosslinked polyethylene (PE-X) — Estimation of the degree of

crosslinking by determination of the
...

NORME ISO
INTERNATIONALE 15875-2
Première édition
2003-12-01
AMENDEMENT 2
2020-11
Systèmes de canalisations en
plastique pour les installations d'eau
chaude et froide — Polyéthylène
réticulé (PE-X) —
Partie 2:
Tubes
AMENDEMENT 2
Plastics piping systems for hot and cold water installations —
Crosslinked polyethylene (PE-X) —
Part 2: Pipes
AMENDMENT 2
Numéro de référence
ISO 15875-2:2003/Amd.2:2020(F)
ISO 2020
---------------------- Page: 1 ----------------------
ISO 15875-2:2003/Amd.2:2020(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2020

Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette

publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,

y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut

être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.

ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 15875-2:2003/Amd.2:2020(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes

nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est

en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.

L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents

critères d'approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www

.iso .org/ directives).

L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de

brevets reçues par l'ISO (voir www .iso .org/ brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion

de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir www .iso .org/ avant -propos.

Le présent document a été élaboré par le Comité technique ISO/TC 138, Tubes, raccords et robinetterie

en matières plastiques pour le transport des fluides, Sous-comité SC 2, Tubes et raccords en matières

plastiques pour adduction et distribution d'eau, en collaboration avec le comité technique CEN/TC 155,

Systèmes de canalisations et de gaines en plastiques, du Comité européen de normalisation (CEN),

conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord de Vienne).

Une liste de toutes les parties de la série ISO 15875 se trouve sur le site web de l’ISO.

Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent

document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes

se trouve à l’adresse www .iso .org/ fr/ members .html.
© ISO 2020 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 15875-2:2003/Amd.2:2020(F)
Systèmes de canalisations en plastique pour les
installations d'eau chaude et froide — Polyéthylène
réticulé (PE-X) —
Partie 2:
Tubes
AMENDEMENT 2
Références normatives
Remplacer la référence à «EN 578» par ce qui suit:
ISO 7686, Tubes et raccords en matières plastiques —
...

INTERNATIONAL ISO
STANDARD 15875-2
First edition
2003-12-01
AMENDMENT 2
ISO pub-date
Plastics piping systems for hot and
cold water installations — Crosslinked
polyethylene (PE-X) —
Part 2:
Pipes
AMENDMENT 2
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polyéthylène réticulé (PE-X) —
Partie 2: Tubes
AMENDEMENT 2
PROOF/ÉPREUVE
Reference number
ISO 15875-2:2003/Amd.2:2020(E)
ISO 2020
---------------------- Page: 1 ----------------------
ISO 15875-2:2003/Amd.2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 15875-2:2003/Amd.2:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for

the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in collaboration

with the European Committee for Standardization (CEN) Technical Committee CEN/TC 155, Plastics

piping systems and ducting systems, in accordance with the Agreement on technical cooperation between

ISO and CEN (Vienna Agreement).
A list of all parts in the ISO 15875 series can be found on the ISO website.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/ members .html.
© ISO 2020 – All rights reserved PROOF/ÉPREUVE iii
---------------------- Page: 3 ----------------------
ISO 15875-2:2003/Amd.2:2020(E)
Plastics piping systems for hot and cold water
installations — Crosslinked polyethylene (PE-X) —
Part 2:
Pipes
AMENDMENT 2
Normative references
Replace the reference to "EN 578" with the following:
ISO 7686, Plastics pipes and fittings — Determination of opacity
Replace the reference to "EN 579" with the following:

ISO 10147, Pipes and fittings made of crosslinked polyethylene (PE-X) — Estimation of the degree of

crosslinking by determination of the gel content
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.