ISO 16422-5:2024
(Main)Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 5: Fitness for purpose of the system
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Part 5: Fitness for purpose of the system
This document specifies the characteristics of the fitness for purpose of oriented unplasticized poly(vinyl chloride) (PVC-O) solid wall piping intended to be used underground or above-ground where protected from direct sunlight, for water supply, buried drainage, sewerage, treated wastewater and irrigation under pressure. It also specifies the test parameters for the test methods referred to in this document. This document is not intended for on-site testing of pipe systems. In conjunction with ISO 16422-1, ISO 16422-2, ISO/TS 16422-3 and ISO 1452-3, this document is applicable to PVC-O pipes and PVC-O fittings, as well as to their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following: a) water mains and services lines; b) conveyance of water for both outside and inside buildings; c) drainage, sewerage and treated wastewater under pressure; d) irrigation under pressure. This document is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for wastewater under pressure. This document is also applicable to components for the conveyance of water and wastewater up to and including 45 °C. For temperatures between 25 °C and 45 °C, see ISO 16422-2:2023, Figure C.1. The piping system according to this document is intended for the conveyance of cold water up to pressures of 25 bar[1] and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bar. [1] 1 bar= 0,1 MPa = 105 Pa; 1 MPa= 1 N/mm2
Tubes et assemblages en poly(chlorure de vinyle) non plastifié orienté (PVC-O) pour le transport de l'eau sous pression — Partie 5: Aptitude à l'emploi du système
General Information
Relations
Buy Standard
Standards Content (Sample)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 16422-5
ISO/TC 138/SC 2
Pipes and joints made of oriented
Secretariat: SNV
unplasticized poly(vinyl chloride)
Voting begins on:
2023-10-18 (PVC-O) for the conveyance of water
under pressure —
Voting terminates on:
2023-12-13
Part 5:
Fitness for purpose of the system
Tubes et assemblages en poly(chlorure de vinyle) non plastifié orienté
(PVC-O) pour le transport de l'eau sous pression —
Partie 5: Aptitude à l'emploi du système
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 16422-5:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 1 ----------------------
ISO/FDIS 16422-5:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 16422-5
ISO/TC 138/SC 2
Pipes and joints made of oriented
Secretariat: SNV
unplasticized poly(vinyl chloride)
Voting begins on:
(PVC-O) for the conveyance of water
under pressure —
Voting terminates on:
Part 5:
Fitness for purpose of the system
Tubes et assemblages en poly(chlorure de vinyle) non plastifié orienté
(PVC-O) pour le transport de l'eau sous pression —
Partie 5: Aptitude à l'emploi du système
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 16422-5:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 2 ----------------------
ISO/FDIS 16422-5:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Fitness for purpose of joints and the system . 2
4.1 General . 2
4.2 Assemblies with non-end-load-bearing joints . 2
4.3 Assemblies with end-load-bearing joints . 3
5 Test methods . 4
5.1 Short-term test for leaktightnes
...
Commented [LJ1]: For the editor – this comment is to be
ISO/FDIS 16422-5:2023(E)
deleted
Date: 2023-07-06
All figures and files are acceptable
ISO /TC 138/SC 2
Jay
Secretariat: SNV
Date: 2023-10-03
Pipes and joints made of oriented unplasticized poly(vinyl
chloride) (PVC-O) for the conveyance of water under pressure —
Fitness for purpose of the system —
Part 5:
Fitness for purpose of the system
Tubes et assemblages en poly(chlorure de vinyle) non plastifié orienté (PVC-O) pour le transport de l'eau
sous pression —
Partie 5: Aptitude à l'emploi du système
FDIS stage
---------------------- Page: 1 ----------------------
ISO/FDIS 16422-5:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
ii © ISO 2023 – All rights reserved
ii © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/FDIS 16422-5:2023(E)
Contents
Foreword . v
Introduction . vi
Part 5: Fitness for purpose of the system . 1
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Fitness for purpose of joints and the system . 3
4.1 General . 3
4.2 Assemblies with non-end-load-bearing joints . 3
4.3 Assemblies with end-load-bearing joints . 4
5 Test methods . 5
5.1 Short-term test for leaktightness under internal pressure with angular deflection . 5
5.1.1 Test procedure . 5
5.1.2 Test pressure . 6
5.2 Short-term test for leaktightness under negative pressure with angular deflection and
deformation . 6
5.3 Long-term leaktightness under internal water pressure . 8
5.3.1 Test procedure . 8
5.4 Short-term positive pressure test for leaktightness of assemblies . 8
5.5 Short-term negative pressure test for leaktightness of assemblies . 8
Annex A (normative) Pressure test for leaktightness of assemblies with end-load-bearing joints . 9
A.1 Introduction .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.