iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 5580

(Main)

Non-destructive testing — Industrial radiographic illuminators — Minimum requirements

Non-destructive testing — Industrial radiographic illuminators — Minimum requirements

The function of illuminators is to allow the viewing of radiographs. The illuminator system shall guarantee the same safety of personnel as an electric apparatus concerning maximum voltage, insulation and earthing.

Essais non destructifs — Négatoscopes utilisés en radiographie industrielle — Exigences minimales

La présente Norme internationale spécifie les exigences minimales que doivent posséder les négatoscopes utilisés pour l'examen des radiogrammes industriels. Un négatoscope a pour fonction de permettre l'examen de radiogrammes. Le négatoscope étant un appareil électrique, il doit, pour garantir la sécurité du personnel qui le manipule, répondre aux exigences de sécurité électrique relatives à la tension maximale, à l'isolation et à la mise à la terre et requises par les normes électrotechniques de chaque pays utilisateur.

General Information

Status
Not Published
ICS
19.100 - Non-destructive testing
Technical Committee
ISO/TC 135/SC 5 - Radiographic testing
Drafting Committee
ISO/TC 135/SC 5 - Radiographic testing
Current Stage
6000 - International Standard under publication
Completion Date
01-Nov-2023
Ref Project

Relations

Revises
ISO 5580:1985 - Non-destructive testing — Industrial radiographic illuminators — Minimum requirements
Effective Date
25-Jun-2022

Buy Standard

ISO/PRF 5580 - Non-destructive testing — Industrial radiographic illuminators — Minimum requirements Released:4. 10. 2023ISO/PRF 5580 - Non-destructive testing — Industrial radiographic illuminators — Minimum requirements Released:4. 10. 2023
PreviousNext
Draft
ISO/PRF 5580 - Non-destructive testing — Industrial radiographic illuminators — Minimum requirements Released:4. 10. 2023
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ISO/PRF 5580 - Non-destructive testing — Industrial radiographic illuminators — Minimum requirements Released:4. 10. 2023REDLINE ISO/PRF 5580 - Non-destructive testing — Industrial radiographic illuminators — Minimum requirements Released:4. 10. 2023
PreviousNext
Draft
REDLINE ISO/PRF 5580 - Non-destructive testing — Industrial radiographic illuminators — Minimum requirements Released:4. 10. 2023
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 5580
Second edition
Non-destructive testing — Industrial
radiographic illuminators —
Minimum requirements
Essais non destructifs — Négatoscopes utilisés en radiographie
industrielle — Exigences minimales
PROOF/ÉPREUVE
Reference number
ISO 5580:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 5580:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
PROOF/ÉPREUVE © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 5580:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Characteristics of radiographic illuminators . 1
4.1 Mechanical and electrical construction . 1
4.2 Viewing screen . 1
4.3 Luminance . 2
4.4 Colour of light . 2
4.5 Diffusion of light . 3
4.6 Uniformity of illumination . 3
4.7 Disturbing light . 3
4.8 Anti-glare device . 3
4.9 Heating. 3
5 Determination of certain characteristics . 3
5.1 General . 3
5.2 Divergence and dispersion of light of diffusing screens . 3
5.3 Uniformity of screen luminance . 4
5.4 Nominal power consumption . 5
6 Marking .
...

ISO 5580:2023(E)
Style Definition: Heading 1: Indent: Left: 0 pt, First
line: 0 pt, Tab stops: Not at 21.6 pt
ISO TC 135/SC 05
Style Definition: Heading 2: Font: Bold, Tab stops: Not
at 18 pt
Secretariat: DIN
Style Definition: Heading 3: Font: Bold
Date: 2023-08-1810-02
Style Definition: Heading 4: Font: Bold
Style Definition: Heading 5: Font: Bold
Non-destructive testing — Industrial radiographic illuminators — Minimum requirements
Style Definition: Heading 6: Font: Bold
Style Definition: ANNEX
Style Definition: Hashtag1
Style Definition: Erwähnung1
Style Definition: Smart Hyperlink1
Style Definition: Nicht aufgelöste Erwähnung2
Style Definition: AMEND Terms Heading: Font: Bold
Style Definition: AMEND Heading 1 Unnumbered:
Font: Bold
Formatted: Font: 11.5 pt, English (United Kingdom)
Formatted: English (United Kingdom)
Formatted: Font color: Auto

---------------------- Page: 1 ----------------------
ISO 5580:2023(E)
Formatted
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part
of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or
mechanical, including photocopying, or posting on the internet or an intranet, without prior written
permission. Permission can be requested from either ISO at the address below or ISO’s member body
in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Formatted: English (United Kingdom)
Formatted: Underline, German (Germany)
Published in Switzerland
Formatted: English (United Kingdom)
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 5580:2023(E)
Contents
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Characteristics of radiographic illuminators . 1
4.1 Mechanical construction . 1
4.2 Viewing screen . 1
4.3 Luminance . 2
4.4 Colour of light . 2
4.5 Diffusion of light . 2
4.6 Uniformity of illumination . 2
4.7 Disturbing light . 2
4.8 Anti-glare device . 3
4.9 Heating . 3
5 Determination of certain characteristics . 3
5.1 General . 3
5.2 Divergence and dispersion of light of diffusing screens . 3
5.3 Uniformity of screen luminance . 4
5.4 Nominal power consumption . 4
6 Marking . 4
7 Recommenda
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 23159:2020(Main)
Non-destructive testing — Gamma ray scanning method on process columns

This document is used for non-destructive testing by the gamma ray scanning method for troubleshooting and testing process columns in industries. This document is applicable to the testing of all kinds of separation processes columns and pipes. This includes columns with different tray configurations and with packed beds.

  • Standard
    27 pages
    English language
    sale 15% off
  • Draft
    27 pages
    English language
    sale 15% off
ISO
ISO 21432:2019(Main)
Non-destructive testing — Standard test method for determining residual stresses by neutron diffraction

This document describes the test method for determining residual stresses in polycrystalline materials by neutron diffraction. It is applicable to both homogeneous and inhomogeneous materials including those containing distinct phases. The principles of the neutron diffraction technique are outlined. Suggestions are provided on: — the selection of appropriate diffracting lattice planes on which measurements should be made for different categories of materials, — the specimen directions in which the measurements should be performed, and — the volume of material examined in relation to the material grain size and the envisaged stress state. Procedures are described for accurately positioning and aligning test pieces in a neutron beam and for precisely defining the volume of material sampled for the individual measurements. The precautions needed for calibrating neutron diffraction instruments are described. Techniques for obtaining a stress-free reference are presented. The methods of making individual measurements by neutron diffraction are described in detail. Procedures for analysing the results and for determining their statistical relevance are presented. Advice is provided on how to determine reliable estimates of residual stresses from the strain data and on how to estimate the uncertainty in the results.

  • Standard
    45 pages
    English language
    sale 15% off
  • Standard
    47 pages
    French language
    sale 15% off
ISO
ISO 20769-1:2018(Main)
Non-destructive testing — Radiographic inspection of corrosion and deposits in pipes by X- and gamma rays — Part 1: Tangential radiographic inspection

This document specifies fundamental techniques of film and digital radiography with the object of enabling satisfactory and repeatable results to be obtained economically. The techniques are based on generally recognized practice and fundamental theory of the subject. This document applies to the radiographic examination of steel pipes for service induced flaws such as corrosion pitting, generalized corrosion and erosion. Besides its conventional meaning, "pipe" as used in this document is understood to cover other cylindrical bodies such as tubes, penstocks, boiler drums and pressure vessels. Weld inspection for typical welding process induced flaws is not covered, but weld inspection is included for corrosion/erosion type flaws. The pipes can be insulated or not, and can be assessed where loss of material due, for example, to corrosion or erosion is suspected either internally or externally. This document covers the tangential inspection technique for detection and through-wall sizing of wall loss, including with the source: a) on the pipe centre line; and b) offset from pipe centre line by the pipe radius. ISO 20769-2 covers double wall radiography, and note that the double wall double image technique is often combined with tangential radiography with the source on the pipe centre line. This document applies to tangential radiographic inspection using industrial radiographic film techniques, computed radiography (CR) and digital detector arrays (DDA).

  • Standard
    37 pages
    English language
    sale 15% off
  • Standard
    41 pages
    French language
    sale 15% off
ISO
ISO 20769-2:2018(Main)
Non-destructive testing — Radiographic inspection of corrosion and deposits in pipes by X- and gamma rays — Part 2: Double wall radiographic inspection

This document specifies fundamental techniques of film and digital radiography with the object of enabling satisfactory and repeatable results to be obtained economically. The techniques are based on generally recognized practice and fundamental theory of the subject. This document applies to the radiographic examination of pipes in metallic materials for service induced flaws such as corrosion pitting, generalized corrosion and erosion. Besides its conventional meaning, "pipe" as used in this document is understood to cover other cylindrical bodies such as tubes, penstocks, boiler drums and pressure vessels. Weld inspection for typical welding process induced flaws is not covered, but weld inspection is included for corrosion/erosion type flaws. The pipes can be insulated or not, and can be assessed where loss of material due, for example, to corrosion or erosion is suspected either internally or externally. This document covers double wall inspection techniques for detection of wall loss, including double wall single image (DWSI) and double wall double image (DWDI). Note that the DWDI technique described in this document is often combined with the tangential technique covered in ISO 20769-1. This document applies to in-service double wall radiographic inspection using industrial radiographic film techniques, computed digital radiography (CR) and digital detector arrays (DDA).

  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    31 pages
    French language
    sale 15% off
ISO
ISO 19232-5:2018(Main)
Non-destructive testing — Image quality of radiographs — Part 5: Determination of the image unsharpness and basic spatial resolution value using duplex wire-type image quality indicators

This document specifies a method of determining the total image unsharpness and basic spatial resolution of radiographs and radioscopic images. The IQI with up to 13 wire pairs can be used effectively with tube voltages up to 600 kV. The IQI with more than 13 wire pairs can be used effectively at tube voltages lower than 225 kV. When using source voltages in the megavolt range, it is possible that the results are not be completely satisfactory.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    12 pages
    French language
    sale 15% off
ISO
ISO 16371-2:2017(Main)
Non-destructive testing — Industrial computed radiography with storage phosphor imaging plates — Part 2: General principles for testing of metallic materials using X-rays and gamma rays

ISO 16371-2:2017 specifies fundamental techniques of computed radiography with the aim of enabling satisfactory and repeatable results to be obtained economically. The techniques are based on the fundamental theory of the subject and tests measurements. ISO 16371-2:2017 specifies the general rules for industrial computed X-rays and gamma radiography for flaw detection purposes, using storage phosphor imaging plates (IP). It is based on the general principles for radiographic examination of metallic materials on the basis of films, as specified in ISO 5579. The basic set-up of radiation source, detector and the corresponding geometry are intended to be applied in accordance with ISO 5579 and corresponding product standards such as ISO 17636 for welding and EN 12681 for foundry. ISO 16371-2:2017 does not lay down acceptance criteria of the imperfections. Computed radiography (CR) systems provide a digital grey value image which can be viewed and evaluated on basis of a computer only. This practice describes the recommended procedure for detector selection and radiographic practice. Selection of computer, software, monitor, printer and viewing conditions are important but not the main focus of ISO 16371-2:2017. The procedure it specifies provides the minimum requirements and practice to permit the exposure and acquisition of digital radiographs with a sensitivity of imperfection detection equivalent to film radiography and as specified in ISO 5579. Some application standards, e.g. EN 16407, can require different and less stringent practice conditions.

  • Standard
    31 pages
    English language
    sale 15% off
  • Standard
    33 pages
    French language
    sale 15% off
ISO
ISO 15708-2:2017(Main)
Non-destructive testing — Radiation methods for computed tomography — Part 2: Principles, equipment and samples

ISO 15708-2:2017 specifies the general principles of X-ray computed tomography (CT), the equipment used and basic considerations of sample, materials and geometry. It is applicable to industrial imaging (i.e. non-medical applications) and gives a consistent set of CT performance parameter definitions, including how those performance parameters relate to CT system specifications. ISO 15708-2:2017 deals with computed axial tomography and excludes other types of tomography such as translational tomography and tomosynthesis.

  • Standard
    17 pages
    English language
    sale 15% off
  • Standard
    18 pages
    French language
    sale 15% off
ISO
ISO 15708-1:2017(Main)
Non-destructive testing — Radiation methods for computed tomography — Part 1: Terminology

ISO 15708-1:2017 gives the definitions of terms used in the field of computed tomography (CT). It presents a terminology that is not only CT-specific but which also includes other more generic terms and definitions spanning imaging and radiography. Some of the definitions represent discussion points aimed at refocusing their terms in the specific context of computed tomography.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
ISO
ISO 15708-3:2017(Main)
Non-destructive testing — Radiation methods for computed tomography — Part 3: Operation and interpretation

ISO 15708-3:2017 presents an outline of the operation of a computed tomography (CT) system and the interpretation of results with the aim of providing the operator with technical information to enable the selection of suitable parameters. It is applicable to industrial imaging (i.e. non-medical applications) and gives a consistent set of CT performance parameter definitions, including how those performance parameters relate to CT system specifications. ISO 15708-3:2017 deals with computed axial tomography and excludes other types of tomography such as translational tomography and tomosynthesis.

  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    21 pages
    French language
    sale 15% off
ISO
ISO 15708-4:2017(Main)
Non-destructive testing — Radiation methods for computed tomography — Part 4: Qualification

ISO 15708-4:2017 specifies guidelines for the qualification of the performance of a CT system with respect to various inspection tasks. It is applicable to industrial imaging (i.e. non-medical applications) and gives a consistent set of CT performance parameter definitions, including how those performance parameters relate to CT system specifications. ISO 15708-4:2017 deals with computed axial tomography and excludes other types of tomography such as translational tomography and tomosynthesis.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    12 pages
    French language
    sale 15% off