ISO 5674:2004
(Main)Tractors and machinery for agriculture and forestry — Guards for power take-off (PTO) drive-shafts — Strength and wear tests and acceptance criteria
Tractors and machinery for agriculture and forestry — Guards for power take-off (PTO) drive-shafts — Strength and wear tests and acceptance criteria
ISO 5674:2004 specifies laboratory tests for determining the strength and wear resistance of guards for PTO drive shafts on tractors and machinery used in agriculture and forestry, and their acceptance criteria. It is intended to be used in combination with ISO 5673. ISO 5674:2004 is applicable to the testing of such PTO drive shaft guards and their restraining means. It is not applicable to the testing of guards designed and constructed to be used as steps. Neither is it applicable to guard types whose use is limited by national regulations.
Tracteurs et matériels agricoles et forestiers — Protecteurs d'arbres de transmission à cardans de prise de force — Essais de résistance mécanique et d'usure et critères d'acceptation
L'ISO 5674:2004 spécifie les essais à mener en laboratoire pour déterminer la résistance mécanique et la résistance à l'usure des protecteurs d'arbres de transmission à cardans de prise de force, et leurs critères d'acceptation. Elle est conçue pour être utilisée conjointement avec l'ISO 5673. L'ISO 5674:2004 est applicable aux essais des protecteurs d'arbres de transmission à cardans de prise de force et à leurs systèmes d'immobilisation. Elle n'est pas applicable aux essais des protecteurs conçus et construits pour être utilisés comme des marchepieds.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 5674
Second edition
2004-03-01
Corrected version
2005-07-01
Tractors and machinery for agriculture
and forestry — Guards for power take-off
(PTO) drive-shafts — Strength and wear
tests and acceptance criteria
Tracteurs et matériels agricoles et forestiers — Protecteurs d'arbres de
transmission à cardans de prise de force — Essais de résistance
mécanique et d'usure et critères d'acceptation
Reference number
©
ISO 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
Contents Page
Foreword. iv
Introduction . v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 General test conditions.2
4.1 Guard.2
4.2 Other.2
5 Test equipment.2
5.1 General.2
5.2 Test parameters.2
6 Tests.4
6.1 General.4
6.2 Wear test.4
6.3 Bearing corrosion test (Perform only if the guard has bearings running in contact with the
PTO-shaft) .4
6.4 Strength tests.5
6.5 Tests at sub-zero temperature .8
6.6 Restraining means test at ambient temperature .10
7 Final acceptance criteria.11
8 Test report.12
Annex A (normative) Test schedule .13
Annex B (normative) UV test for plastic guards .16
Annex C (informative) Typical test report.17
Annex D (informative) Novel design guard and restraining systems tests.20
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5674 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 2, Common tests.
This second edition of ISO 5674 cancels and replaces the first editions of ISO 5674-1:1992 and
ISO 5674-2:1992, of which it constitutes a technical revision.
This corrected version of ISO 5674:2004 incorporates the following corrections or modifications.
An error in the second column heading of Table 2 (“m/m”) has been eliminated.
Figure 1 has been modified, and numbering of elements and a key added.
The wording of the third sentence of 6.5.2 has been changed.
The title of 6.6 has been corrected from “specified temperature” to “ambient temperature”.
The system of numbering and the wording of A.1 has been altered to avoid possible confusion.
Figure A.1 has been changed to show the blows at three locations, and “h” has been deleted from the
drawing and the legend as a result of the change to 6.5.2.
Cross-references have been added to the legend to Figure D.1.
The system of numbering and the wording of D.9 has been altered to avoid possible confusion.
iv © ISO 2004 – All rights reserved
Introduction
This document is a type C standard as stated in ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.
INTERNATIONAL STANDARD ISO 5674:2004(E)
Tractors and machinery for agriculture and forestry — Guards
for power take-off (PTO) drive-shafts — Strength and wear tests
and acceptance criteria
1 Scope
This International Standard specifies laboratory tests for determining the strength and wear resistance of
guards for power take-off (PTO) drive-shafts on tractors and machinery used in agriculture and forestry, and
their acceptance criteria. It is intended to be used in combination with ISO 5673.
It is applicable to the testing of PTO drive-shaft guards and their restraining means. It is not applicable to the
testing of guards designed and constructed to be used as steps.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 500 (all parts), Agricultural tractors — Rear-mounted power take-off types 1, 2 and 3
ISO 4892-1, Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance
ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc sources
ISO 5673-1, Agricultural tractors and machinery — Power take-off drive shafts and power-input connection —
Part 1: General, manufacturing and safety requirements
ISO 5673-2, Agricultural tractors and machinery — Power take-off drive shafts and power-input connection —
Part 2: Specification for use of PTO drive shafts, and position and clearance of PTO drive line and PIC for
various attachments
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5673-1 and the following apply.
3.1
ambient temperature
any temperature between 5 °C and 35 °C
4 General test conditions
4.1 Guard
4.1.1 The guard shall be representative of a production model and be within the tolerances specified for the
guard. The results obtained from the sample can be used to certify guards of shorter or longer lengths,
provided the basic design remains the same. When a guard is designed for use with several drive-shaft types,
a representative selection of shaft and guard combinations shall be tested.
4.1.2 If the guard is made of plastic material (or any other material susceptible to degradation by UV
radiation), it shall be certified by the manufacturer to be resistant to degradation from UV radiation under an
appropriate, recognized method. See Annex B for an example.
4.1.3 During testing, all operating and maintenance instructions specified for the shaft and guard shall be
complied with, except where specifically mentioned by this International Standard.
4.1.4 The guard shall be tested in conjunction with a PTO drive-shaft of between 900 mm and 1 010 mm
closed length for which it is intended. The same guard shall be used throughout all the tests.
4.2 Other
4.2.1 Where specified in this International Standard that the PTO drive-shaft shall be revolving, its rotational
frequency shall be 1 000 r/min.
4.2.2 All tests shall be carried out in accordance with the schedule and in the sequence given in Annex A.
5 Test equipment
5.1 General
5.1.1 Wear test equipment, which shall be capable of holding the PTO drive-shaft and revolving it at a
frequency of 1 000 r/min.
The shafts and guards shall be mounted as specified for operational use and only fixed by their designated
restraining device. The fixing points shall be in accordance with ISO 500 and the equivalent machine standard
unless otherwise specified for that type of shaft. The size and shape of the wear test equipment shall be such
that an even test environment is maintained, e.g. heat and the dust specified in 5.2.3.
5.1.2 Strength test equipment, which shall allow the accurate application of known loads at controlled
temperatures and at the required frequency of rotation within the tolerances stipulated in Table 1.
5.2 Test parameters
5.2.1 Measuring accuracy
All measurements shall be within the tolerances given in Table 1 except where otherwise required by this
International Standard.
2 © ISO 2004 – All rights reserved
Table 1 — Measuring accuracy
Measuring accuracy Test tolerance
Rotational speed ± 0,5 % + 5 %
Temperature ± 1,0 °C ± 5 %
Time ± 0,2 % + 5 %
Length ± 0,5 % ± 2 %
Force ± 1,0 % + 2 %
5.2.2 Potable and salt water
5.2.2.1 When a test requires the use of water, it shall be potable (i.e. drinking water).
5.2.2.2 When a test requires a saltwater solution, it shall be prepared by dissolving sodium chloride in
water to produce a concentration of 50 g/l ± 5 g/l. The sodium chloride shall be white and shall give a
colourless solution in water. It shall be substantially free from copper and nickel, and shall not contain more
than 0,1 % of sodium iodine and not more than 0,4 % of total impurities calculated for dry salt.
5.2.3 Test dust
5.2.3.1 The test dust shall consist of a mixture composed of equal parts, by mass, of organic and mineral
dust.
5.2.3.2 The organic dust shall be ground lucerne with a maximum percentage of 12 % water and with a
maximum particle size of 2 mm. An environment of 0,5 kg/m shall be maintained.
5.2.3.3 The mineral dust shall be a simple phosphated fertilizer, and shall contain as principal elements
silicophosphates of calcium having the following characteristics:
minimum content: 9 % of P O total (± 3 %);
2 5
other: at least 75 % of the P O total decla
...
NORME ISO
INTERNATIONALE 5674
Deuxième édition
2004-03-01
Version corrigée
2005-07-01
Tracteurs et matériels agricoles et
forestiers — Protecteurs d'arbres de
transmission à cardans de prise de
force — Essais de résistance mécanique
et d'usure et critères d'acceptation
Tractors and machinery for agriculture and forestry — Guards for power
take-off (PTO) drive-shafts — Strength and wear tests and acceptance
criteria
Numéro de référence
©
ISO 2004
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2004
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2004 – Tous droits réservés
Sommaire Page
Avant-propos. iv
Introduction . v
1 Domaine d'application. 1
2 Références normatives . 1
3 Termes et définitions. 1
4 Conditions générales d’essai . 2
4.1 Protecteur . 2
4.2 Autres. 2
5 Équipement d’essai . 2
5.1 Généralités . 2
5.2 Paramètres d'essai . 3
6 Essais. 3
6.1 Généralités . 3
6.2 Essai d’usure. 4
6.3 Essai de corrosion des paliers (À n’exécuter que si les paliers du protecteur sont, pendant
leur fonctionnement, en contact avec l’arbre à cardans de p.d.f.). 4
6.4 Essais de résistance mécanique. 5
6.5 Essais aux températures de gel. 8
6.6 Essai des systèmes d’immobilisation à température ambiante . 10
7 Critères finaux d’acceptation . 10
8 Rapport d’essai . 12
Annexe A (normative) Programme des essais. 13
Annexe B (normative) Essais aux ultraviolets pour protecteurs en plastique. 16
Annexe C (informative) Modèle de rapport d'essai. 17
Annexe D (informative) Essais des nouveaux modèles de protecteurs et de systèmes
d'immobilisation. 20
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 5674 a été élaborée par le comité technique ISO/TC 23, Tracteurs et matériels agricoles et forestiers,
sous-comité SC 2, Essais communs.
Cette deuxième édition de l’ISO 5674 annule et remplace les premières éditions de l’ISO 5674-1:1992 et de
l’ISO 5674-2:1992, qui ont fait l'objet d'une révision technique.
Cette version corrigée de l’ISO 5674:2004 incorpore les corrections ou modifications suivantes.
Dans le Tableau 2, deuxième colonne, l’expression «Fraction massique» a été supprimée.
La Figure 1 a été modifiée, et les numéros des éléments ont été ajoutés sous «Légende».
Le troisième alinéa de 6.5.2 a été modifié.
Dans le titre de 6.6, «à une température spécifiée» a été remplacée par «à température ambiante».
Le système de numérotation et la rédaction de A.1 ont été remaniés pour éviter une possible confusion.
La Figure A.1 a été complétée pour montrer les coups en trois positions, et la note de bas de figure «h» a
été supprimée en raison des changements en 6.5.2.
Des références croisées ont été ajoutées à la légende de la Figure D.1.
Le système de numérotation et la rédaction de D.9 ont été remaniés pour éviter une possible confusion.
iv © ISO 2004 – Tous droits réservés
Introduction
Le présent document est une norme de type C tel qu'énoncé dans l'ISO 12100.
Les machines concernées et l’étendue des phénomènes dangereux, des situations dangereuses et des
événements dangereux couverts sont indiqués dans le domaine d’application de la présente norme.
Lorsque des dispositions de la présente norme de type C sont différentes de celles énoncées dans les
normes de type A ou B, les dispositions de la présente norme de type C prennent le pas sur les dispositions
des autres normes, pour les machines ayant été conçues et construites conformément aux dispositions de la
présente norme de type C.
NORME INTERNATIONALE ISO 5674:2004(F)
Tracteurs et matériels agricoles et forestiers — Protecteurs
d'arbres de transmission à cardans de prise de force — Essais
de résistance mécanique et d'usure et critères d'acceptation
1 Domaine d'application
La présente Norme internationale spécifie les essais à mener en laboratoire pour déterminer la résistance
mécanique et la résistance à l’usure des protecteurs d’arbres de transmission à cardans de prise de force
(p.d.f.), et leurs critères d’acceptation. Elle est conçue pour être utilisée conjointement avec l’ISO 5673.
Elle est applicable aux essais des protecteurs d’arbres de transmission à cardans de p.d.f. et à leurs
systèmes d'immobilisation. Elle n’est pas applicable aux essais des protecteurs conçus et construits pour être
utilisés comme des marchepieds.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 105-A02, Textiles — Essais de solidité des teintures — Partie A02: Échelle de gris pour l'évaluation des
dégradations
ISO 500 (toutes les parties), Tracteurs agricoles — Prises de force montées à l'arrière des types 1, 2 et 3
ISO 4892-1, Plastiques — Méthodes d'exposition à des sources lumineuses de laboratoire — Partie 1: Guide
général
ISO 4892-2, Plastiques — Méthodes d'exposition à des sources lumineuses de laboratoire — Partie 2:
Sources à arc au xénon
ISO 5673-1, Tracteurs et matériels agricoles — Arbres de transmission à cardans de prise de force et arbre
récepteur de la machine — Partie 1: Exigences générales de fabrication et de sécurité
ISO 5673-2, Tracteurs et matériels agricoles — Arbres de transmission à cardans de prise de force et arbre
récepteur de la machine — Partie 2: Spécifications relatives à l’utilisation des arbres de transmission à
cardans de prise de force, et position et dégagement de la ligne de transmission de prise de force et de l'arbre
récepteur de la machine pour différents systèmes d'attelage
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 5673-1 ainsi que le terme
et la définition suivants s'appliquent.
3.1
température ambiante
toute température comprise entre 5 °C et 35 °C
4 Conditions générales d’essai
4.1 Protecteur
4.1.1 Le protecteur doit être représentatif d’un modèle de série et respecter les tolérances correspondantes.
Les résultats obtenus sur l’échantillon peuvent être utilisés pour certifier des protecteurs plus longs ou plus
courts si la conception de base reste la même. Lorsque le protecteur est conçu pour être utilisé avec plusieurs
types d’arbre de transmission, les essais doivent porter sur une sélection représentative de combinaisons
d’arbres et de protecteurs.
4.1.2 Si le protecteur est en matière plastique (ou en tout autre matériau susceptible de dégradation par les
rayonnements ultraviolets), il doit être certifié par le constructeur comme résistant aux UV par une méthode
appropriée reconnue. Voir l’Annexe B pour un exemple.
4.1.3 Durant les essais, toutes les instructions relatives au fonctionnement et à la maintenance de l’arbre et
du protecteur doivent être respectées, sauf stipulation contraire dans la présente Norme internationale.
4.1.4 Le protecteur doit être soumis à l'essai en même temps qu’un arbre de transmission à cardans de
p.d.f., pour lequel il est conçu, de longueur rétractée comprise entre 900 mm et 1 010 mm. Le même
protecteur doit être utilisé tout au long des essais.
4.2 Autres
4.2.1 Lorsque la présente Norme internationale spécifie que l’arbre de transmission à cardans de p.d.f. doit
tourner, sa fréquence de rotation doit être de 1 000 r/min.
4.2.2 Tous les essais doivent être réalisés conformément au programme et suivant la séquence indiqués à
l’Annexe A.
5 Équipement d’essai
5.1 Généralités
5.1.1 Équipement pour l'essai d’usure, pouvant maintenir l’arbre de transmission à cardans de p.d.f. et le
faire tourner à une fréquence de 1 000 r/min.
Les arbres et les protecteurs doivent être montés de la manière spécifiée pour l’utilisation normale et ne
doivent être immobilisés qu’au moyen de leur dispositif d'immobilisation désigné. Les points de fixation
doivent être conformes à l’ISO 500 et à la norme de machine équivalente sauf stipulation contraire pour le
type d’arbre considéré. La taille et la forme de l’équipement pour l’essai d’usure doivent permettre de
maintenir un environnement d’essai uniforme: la chaleur et la poussière doivent, par exemple, être conformes
aux spécifications données en 5.2.3.
5.1.2 Équipement pour l’essai de résistance mécanique, permettant l’application précise de charges
connues à des températures contrôlées et à la fréquence de rotation requise, compte tenu des tolérances
spécifiées au Tableau 1.
Tableau 1 — Exactitude de mesure
Exactitude de mesure Tolérances d'essai
Vitesse de rotation ± 0,5 % + 5 %
Température ± 1,0 °C ± 5 %
Temps ± 0,2 % + 5 %
Longueur
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.