ISO 15645:2002

Road construction and maintenance equipment — Road milling machinery — Terminology and commercial specifications

Équipement pour la construction et l'entretien des routes — Fraiseuses — Terminologie et spécifications commerciales

General Information

• Status: Withdrawn
• Publication Date: 15-May-2002
• Withdrawal Date: 15-May-2002
• ICS: 93.080.10 - Road construction
• Technical Committee: ISO/TC 195 - Building construction machinery and equipment
• Drafting Committee: ISO/TC 195/WG 5 - Road construction and maintenance equipment - Terminology and commercial specifications
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 12-Sep-2018

Relations

• Revised: ISO 15645:2018 - Road construction and maintenance equipment — Road milling machinery — Terminology and commercial specifications
• Effective Date: 10-Dec-2016
• Amended By: ISO 15645:2002/Amd 1:2013 - Road construction and maintenance equipment — Road milling machinery — Terminology and commercial specifications — Amendment 1
• Effective Date: 24-Jul-2021
• Consolidated By: ISO 11925-2:2010 - Reaction to fire tests — Ignitability of products subjected to direct impingement of flame — Part 2: Single-flame source test
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 15645
First edition
2002-05-01
Road construction and maintenance
equipment — Road milling machinery —
Terminology and commercial specifications
Équipement pour la construction et l'entretien des routes — Fraiseuses —
Terminologie et spécifications commerciales

Reference number
ISO 15645:2002(E)
©
ISO 2002

---------------------- Page: 1 ----------------------
ISO 15645:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2002 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 15645:2002(E)
Contents Page
1 Scope . 1
2 Terms and definitions . 1
3 Description of milling machine components . 2
3.1 General . 2
3.2 Design of milling machine types . 2
4 Commercial specifications . 3
4.1 Characteristics of the traction and transport vehicle . 3
4.2 Cutting and milling system characteristics . 4
4.3 Drum sprinkler device . 5
4.4 System to remove or cordon aggregate materials . 5
©
ISO 2002 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 15645:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO15645 was prepared by Technical Committee ISO/TC195, Building construction
machinery and equipment.
©
iv ISO 2002 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 15645:2002(E)
Introduction
This International Standard deals with road milling machinery used in the retread process, which is carried out in
road maintenance.
It provides definitions of the milling machine itself and its components, and technical characteristics.
It includes figures showing milling machines with a loading device and the positioning of work tools in a rotor.
©
ISO 2002 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 15645:2002(E)
Road construction and maintenance equipment — Road milling
machinery — Terminology and commercial specifications
1 Scope
This International Standard establishes the terminology, functions, types and characteristics of road milling
machinery.
It is applicable to the planing of pavements made of concrete, asphalt and similar materials with a view to removing
them.
2 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
2.1
road milling machinery
mobile road construction machine used to mill materials from paved surfaces
2.2
road milling carrier
machine carrying all the systems constituting the road milling machine, distributing the necessary power to operate
the different devices and to ensure movement during work and transfer
2.3
cutting and milling system
power-driven cylindrical bodies on which the milling tools are fitted
NOTE The cylindrical bodies rotate during the milling operation. The tools are mostly cooled by a water sprinkler device.
2.4
levelling system
automatic or manual system used to obtain and maintain the geometry of the bottom of the cut
NOTE The geometry of the bottom refers to both the longitudinal and cross-sections. The geometrical reference is taken from the
existing section or from a specific layout.
2.5
system to remove or make a cordon of aggregate material
transport system for removal and storage of loose material
NOTE The material is removed by either a front-, rear- or side-loading system, or is deposited as a cordon at the side or the back
of the road milling machine.
2.6
operating mass
mass of the base machine with all standard equipment, with or without cab, with or without ROPS, etc., with operator
(75 kg) and full fuel tank, and all fluid systems at their rated capacities and, when applicable, with sprinkler water tank
half full
©
ISO 2002 – All rights reserved 1

------------
...