ISO 6362-7:2014

Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 7: Chemical composition

ISO 6362-7:2014 specifies the chemical composition of wrought aluminium and aluminium alloys. The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association (known as the "Teal Sheets"), for the corresponding alloys.

Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 7: Composition chimique

General Information

• Status: Withdrawn
• Publication Date: 16-Sep-2014
• ICS: 77.150.10 - Aluminium products
• Technical Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Drafting Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 01-Jul-2022

Relations

• Revised: ISO 6362-7:2022 - Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 7: Chemical composition
• Effective Date: 23-Apr-2020
• Revises: ISO 6362-7:2012 - Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 7: Chemical composition
• Effective Date: 19-Oct-2013

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6362-7
Second edition
2014-09-15
Wrought aluminium and aluminium
alloys — Extruded rods/bars, tubes
and profiles —
Part 7:
Chemical composition
Aluminium et alliages d’aluminium corroyés — Barres, tubes et
profilés filés —
Partie 7: Composition chimique
Reference number
ISO 6362-7:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 6362-7:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6362-7:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Chemical composition . 1
Annex A (normative) Rules for rounding for determination of compliance .6
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6362-7:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 79, Light metals and their alloys, Subcommittee
SC 6, Wrought aluminium and aluminium alloys.
This second edition cancels and replaces the first edition (ISO 6362-7:2012), which has been technically
revised.
ISO 6362 consists of the following parts, under the general title Wrought aluminium and aluminium
alloys — Extruded rods/bars, tubes and profiles:
— Part 1: Technical conditions for inspection and delivery
— Part 2: Mechanical properties
— Part 3: Extruded rectangular bars — Tolerances on shape and dimensions
— Part 4: Profiles — Tolerances on shape and dimensions
— Part 5: Round, square and hexagonal bars — Tolerances on shape and dimensions
— Part 6: Round, square, rectangular and hexagonal tubes — Tolerances on shape and dimensions
— Part 7: Chemical composition
iv © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 6362-7:2014(E)
Wrought aluminium and aluminium alloys — Extruded
rods/bars, tubes and profiles —
Part 7:
Chemical composition
1 Scope
This part of ISO 6362 specifies the chemical composition of wrought aluminium and aluminium alloys.
The chemical composition limits of aluminium and aluminium alloys specified herein are completely
identical with those registered with the Aluminium Association, 1525 Wilson Boulevard, Suite 600,
Arlington, VA 22209, USA (known as the “Teal Sheets”), for the corresponding alloys.
NOTE In the case of a discrepancy in the values listed in Table 1 with those listed in the “Registration Record
Series Teal Sheets, International Alloy Destinations and Chemical Composition Limits for Wrought Aluminum and
Wrought Aluminum Alloys”, the composition limits registered with the Aluminium Association and published in
the “Teal Sheets” can be considered for controlling the composition.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 209, Aluminium and aluminium alloys — Chemical composition
ISO 6362-1, Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 1:
Technical conditions for inspection and delivery
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6362-1 apply.
4 Chemical composition
The chemical designations are specified in ISO 209.
The chemical composition of the aluminium and aluminium alloys is given in percentage by mass in
Table 1.
For the purpose of determining conformance to these limits, an observed value or a calculated value
obtained from analysis is rounded off, in accordance with the rules for rounding given in Annex A.
The conformance does not preclude the possible presence of other elements that are not specified. If the
purchaser’s requirements necessitate limits for any other element not specified, these shall be agreed
upon between the supplier and purchaser. “The remainder” is the difference between 100 % and the
sum of all other metallic elements present in amounts of 0,010 % or more each, expressed to the second
decimal place before determining the sum.
© ISO 2014 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 6362-7:2014(E)

Table 1 — Chemical composition (% by mass)
Others
Alloy Limit Si Fe Cu Mn Mg Cr Zn Ti Remarks Aluminium
Each Total
min. — — — — — — — — — — 99,70
1070 V 0,05 max.
max. 0,20 0,25 0,04 0,03 0,03 — 0,04 0,03 0,03 — —
min. — — — — — — — — — — 99,70
1070A —
max. 0,20 0,25 0,03 0,03 0,03 — 0,07 0,03 0,03 — —
min. — — — — — — — — — — 99,60
1060 —
max. 0,25 0,35 0,05 0,03 0,03 — 0,05 0,03 0,03 — —
min. — — — — — — — — — — 99,50
1050 V 0,05 max.
max. 0,25 0,40 0,05 0,05 0,05 — 0,05 0,03 0,03 — —
min. — — — — — — — — — — 99,50
1050A —
max. 0,25 0,40 0,05 0,05 0,05 — 0,07 0,05 0,03 — —
B 0,05 max.
min. — — — — — — — — — — 99,50
1350 Ga 0,03 max.
max. 0,10 0,40 0,05 0,01 — 0,01 0,05 — 0,03 0,10 —
V+Ti 0,02 max.
min. — 0,05 — — — — — — — 99,00
a
1100
max. Si+Fe:0,95 0,20 0,05 — — 0,10 — 0,05 0,15 —
min. — — — — — — — — — 99.00
1200 —
max. Si+Fe:1,00 0,05 0,05 — — 0,10 0,05 0,05 0,15 —
Ni 0,20 max.
min. — — 3,3 0,50 0,40 — — — Bi 0,20 max. — —
2007 Remainder
max. 0,8 0,8 4,6 1,0 1,8 0,10 0,8 0,20 Pb 0,8 to 1,5 0,10 0,30
Sn 0,20 max.
min. — — 5,0 — — — — — Bi 0,20 to 0,6 — —
2011 Remainder
max. 0,40 0,7 6,0 — — — 0,30 — Pb 0,20 to 0,6 0,05 0,15
min. — — 4,5 — — — — — Bi 0,20 to 0,6 — —
2011A Remainder
max. 0,40 0,50 6,0 — — — 0,30 — Pb 0,20 to 0,6 0,05 0,15
min. 0,50 — 3,9 0,40 0,20 — — — — —
b
2014 Remainder
max. 1,2 0,7 5,0 1,2 0,8 0,10 0,25 0,15 0,05 0,15
min. 0,50 — 3,9 0,40 0,20 — — — Zr+Ti 0,25 max. — —
2014A Remainder
max. 0,9 0,
...