ISO 17632:2015
(Main)Welding consumables — Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels — Classification
Welding consumables — Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels — Classification
ISO 17632:2015 specifies requirements for classification of tubular cored electrodes with or without a gas shield for metal arc welding of non-alloy and fine grain steels in the as-welded condition or in the post-weld heat-treated condition with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa. One tubular cored electrode can be tested and classified with different shielding gases, if any. This International Standard is a combined specification providing classification utilizing a system based upon the yield strength and the average impact energy of 47 J of all-weld metal or utilizing a system based upon the tensile strength and the average impact energy of 27 J of all-weld metal. 1) Paragraphs and tables which carry the suffix letter "A" are applicable only to tubular cored electrodes classified to the system based upon the yield strength and the average impact energy of 47 J of all-weld metal in accordance with this International Standard. 2) Paragraphs and tables which carry the suffix letter "B" are applicable only to tubular cored electrodes classified to the system based upon the tensile strength and the average impact energy of 27 J of all-weld metal in accordance with this International Standard. 3) Paragraphs and tables which have neither the suffix letter "A" nor the suffix letter "B" are applicable to all tubular cored electrodes classified in accordance with this International Standard. It is recognized that the operating characteristics of tubular cored electrodes can be modified by the use of pulsed current, but for the purposes of this International Standard, pulsed current is not permitted for determining the electrode classification.
Produits consommables pour le soudage — Fils-électrodes fourrés pour soudage à l'arc avec ou sans gaz de protection des aciers non alliés et des aciers à grains fins — Classification
ISO 17632:2015 spécifie les exigences relatives à la classification des fils-électrodes fourrés pour soudage à l'arc avec ou sans gaz de protection pour l'état brut de soudage ou pour l'état traité thermiquement après soudage des aciers non alliés et des aciers à grains fins, ayant une limite d'élasticité minimale pouvant atteindre 500 MPa ou une résistance à la traction minimale pouvant atteindre 570 MPa. Un fil-électrode peut, le cas échéant, être essayé et classifié avec différents gaz de protection. La présente Norme internationale propose une spécification mixte permettant une classification utilisant un système basé soit sur la limite d'élasticité et l'énergie de rupture moyenne de 47 J pour le métal fondu hors dilution, soit sur la résistance à la traction et l'énergie de rupture moyenne de 27 J pour le métal fondu hors dilution. 1) Les paragraphes et les tableaux qui portent le suffixe «A» ne sont applicables qu'aux fils-électrodes classifiés d'après le système basé sur la limite d'élasticité et l'énergie de rupture moyenne de 47 J pour le métal fondu hors dilution conformément à la présente Norme internationale. 2) Les paragraphes et les tableaux qui portent le suffixe «B» ne sont applicables qu'aux fils-électrodes classifiés d'après le système basé sur la résistance à la traction et l'énergie de rupture moyenne de 27 J pour le métal fondu hors dilution conformément à la présente Norme internationale. 3) Les paragraphes et les tableaux qui ne portent ni le suffixe «A» ni le suffixe «B» sont applicables à tous les fils-électrodes classifiés conformément à la présente Norme internationale. Il est connu que les caractéristiques d'emploi d'un fil-électrode fourré peuvent être modifiées par l'utilisation de courant pulsé mais, pour les besoins de la présente Norme internationale, l'utilisation de courant pulsé pour la détermination de la classification d'un fil-électrode n'est pas autorisée.
General Information
Relations
Buy Standard
Standards Content (Sample)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 17632
ISO/TC 44/SC 3 Secretariat: ANSI
Voting begins on: Voting terminates on:
2013-09-12 2014-02-12
Welding consumables — Tubular cored electrodes for gas
shielded and non-gas shielded metal arc welding of non-
alloy and fine grain steels — Classification
Produits consommables pour le soudage — Fils-électrodes fourrés pour soudage à l’arc avec ou sans gaz de
protection des aciers non alliés et des aciers à grains fins — Classification
[Revision of first edition (ISO 17632:2004)]
ICS: 25.160.20
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 17632:2013(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2013
ISO/DIS 17632:2013(E)
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2013 – All rights reserved
ISO/DIS 17632
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Classification . 2
4 Symbols and requirements . 4
4.1 Symbol for the product/process . 4
4.2 Symbol for tensile properties of all-weld metal or welded joint . 4
4.2.1 Multi-run technique . 4
4.2.2 Single-run technique . 5
4.3 Symbol for impact properties of all-weld metal or welded joint . 5
4.4 Symbol for chemical composition of all-weld metal . 6
4.5 Symbol for type of electrode core or for the usability characteristics of the electrode . 9
4.6 Symbol for shielding gas . 10
4.7 Symbol for welding position . 13
4.8 Symbol for hydrogen content of deposited metal . 13
4.9 Symbol for condition of postweld heat treatment of all-weld metal. 14
5 Mechanical tests . 14
5.1 Multi-run technique . 14
5.1.1 Preheating and interpass temperatures . 14
5.1.2 Procedure requirements for welding multi-run test assemblies. . 15
5.1.3 Post-weld heat treatment (PWHT) condition . 16
5.2 Single-run technique . 16
6 Chemical analysis . 16
7 Rounding procedure . 16
8 Fillet weld test . 16
9 Retests . 17
10 Technical delivery conditions . 17
11 Examples of designation . 18
Annex A (informative) Classification systems .20
Annex B (informative) Description of types of electrode core in the classification system based
upon yield strength and average impact energy of 47 J . 23
Annex C (informative) Description of types of usability characteristics in the classification system
based upon tensile strength and average impact energy of 27 J . 25
Annex D (informative) Notes on hydrogen content . 28
ISO/DIS 17632
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17632 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
This second/third/. edition cancels and replaces the first/second/. edition (), [clause(s) / subclause(s) /
table(s) / figure(s) / annex(es)] of which [has / have] been technically revised.
iv © ISO 2013 – All rights reserved
ISO/DIS 17632
Introduction
This International Standard provides a classification system for tubular cored electrodes in terms of tensile
properties, impact properties, chemical composition of the all-weld metal, type of electrode core, shielding gas
and welding position. The ratio of yield to tensile strength of weld metal is generally higher than that of parent
metal. Users should note that matching weld metal yield strength to parent metal yield strength will not
necessarily ensure that the weld metal tensile strength matches that of the parent metal. Where the
application requires matching tensile strength, therefore, selection of the consumable should be made by
reference to column 3 of Table 1A or Table 1B.
It should be noted that the mechanical properties of all-weld metal test specimens used to classify the tubular
cored electrodes will vary from those obtained in production joints because of differences in welding
procedure such as electrode size, width of weave, welding position and parent metal composition.
The classification according to system A is mainly based on EN 758:1997, Welding consumables — Tubular
cored electrodes for metal arc welding with and without a gas shield of non alloy and fine grain steels —
Classification. The classification according to system B is mainly based upon standards used around the
Pacific Rim.
DRAFT INTERNATIONAL STANDARD ISO/DIS 17632
Welding consumables — Tubular cored electrodes for gas
shielded and non-gas shielded metal arc welding of non-alloy
and fine grain steels — Classification
1 Scope
This International Standard specifies requirements for classification of tubular cored electrodes with or without
a gas shield for metal arc welding of non-alloy and fine grain steels in the as-welded condition or in the post-
weld heat-treated condition with a minimum yield strength of up to 500 MPa or a minimum tensile strength of
up to 570 MPa. One tubular cored electrode can be tested and classified with different shielding gases, if any.
This International Standard is a combined specification providing classification utilizing a system based upon
the yield strength and the average impact energy of 47 J of all-weld metal, or utilizing a system based upon
the tensile strength and the average impact energy of 27 J of all-weld metal.
1) Paragraphs and tables which carry the suffix letter “A” are applicable only to tubular cored electrodes
classified to the system based upon the yield strength and the average impact energy of 47 J of all-
weld metal in accordance with this International Standard.
2) Paragraphs and tables which carry the suffix letter “B” are applicable only to tubular cored electrodes
classified to the system based upon the tensile strength and the average impact energy of 27 J of all-
weld metal in accordance with this International Standard.
3) Paragraphs and tables which have neither the suffix letter “A” nor the suffix letter “B” are applicable
to all tubular cored electrodes classified in accordance with this International Standard.
It is recognized that the operating characteristics of tubular cored electrodes can be modified by the use of
pulsed current, but for the purposes of this International Standard, pulsed current is not permitted for
determining the electrode classification.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 544, Welding consumables – Technical delivery conditions for filler materials and fluxes – Type of product,
dimensions, tolerances and markings
ISO 3690, Welding and allied processes -- Determination of hydrogen content in arc weld metal
ISO 6847, Welding consumables -- Deposition of a weld metal pad for chemical analysis
ISO 6947:2011, Welding and allied processes -- Welding positions
ISO 13916, Welding — Guidance on the measurement of preheating temperature, interpass temperature and
preheat maintenance temperature
ISO 14175:2008, Welding consumables – Gases and gas mixtures for fusion welding and allied processes
ISO/DIS 17632
ISO 14344, Welding consumables – Procurement of filler materials and fluxes
ISO 15792-1:2000/ Amd 1:2011, Welding Consumables — Test methods — Part 1: Test methods for all-weld
metal test specimens in steel, nickel and nickel alloys
ISO 15792-2:2000, Welding Consumables — Test methods — Part 2: Preparation of single-run and two-run
technique test specimens in steel
ISO 15792-3, Welding Consumables — Test methods — Part 3: Classification testing of positional capacity
and root penetration of welding consumables in a fillet weld
ISO 80000-1:2009, Quantities and units — Part 1: General
3 Classification
Classification designations are based upon two approaches to indicate the tensile properties and the impact
properties of the all-weld metal obtained with a given electrode. The two designation approaches include
additional designators for some ot
...
INTERNATIONAL ISO
STANDARD 17632
Second edition
2015-11-15
Welding consumables — Tubular
cored electrodes for gas shielded and
non-gas shielded metal arc welding
of non-alloy and fine grain steels —
Classification
Produits consommables pour le soudage — Fils-électrodes fourrés
pour soudage à l’arc avec ou sans gaz de protection des aciers non
alliés et des aciers à grains fins — Classification
Reference number
©
ISO 2015
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Classification . 2
4 Symbols and requirements . 3
4.1 Symbol for the product/process . 3
4.2 Symbol for tensile properties of all-weld metal or welded joint . 4
4.2.1 Multi-run technique . 4
4.2.2 Single-run technique . 4
4.3 Symbol for impact properties of all-weld metal or welded joint . 5
4.4 Symbol for chemical composition of all-weld metal. 6
4.5 Symbol for type of electrode core or for the usability characteristics of the electrode . 9
4.6 Symbol for shielding gas . 9
4.7 Symbol for welding position .12
4.8 Symbol for hydrogen content of deposited metal .12
4.9 Symbol for condition of postweld heat treatment of all-weld metal .13
5 Mechanical tests .13
5.1 Multi-run technique .13
5.1.1 Preheating and interpass temperatures .13
5.1.2 Procedure requirements for welding multi-run test assemblies .14
5.1.3 Post-weld heat treatment (PWHT) condition .15
5.2 Single-run technique .15
6 Chemical analysis .15
7 Rounding procedure .15
8 Fillet weld test .15
9 Retests .16
10 Technical delivery conditions .17
11 Examples of designation .17
Annex A (informative) Classification systems .21
Annex B (informative) Description of types of electrode core in the classification system
based upon yield strength and average impact energy of 47 J .24
Annex C (informative) Description of types of usability characteristics in the classification
system based upon tensile strength and average impact energy of 27 J .26
Annex D (informative) Notes on hydrogen content .29
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
This second edition cancels and replaces the first edition (ISO 17632:2004), which has been
technically revised.
Requests for official interpretations of any aspect of this International Standard should be directed to
the Secretariat of ISO/TC 44/SC 3, through your national standards body, a complete listing of which
can be found at www.iso.org.
iv © ISO 2015 – All rights reserved
Introduction
This International Standard provides a classification system for tubular cored electrodes in terms of
tensile properties, impact properties, chemical composition of the all-weld metal, type of electrode
core, shielding gas, and welding position. The ratio of yield to tensile strength of weld metal is generally
higher than that of the parent metal. Matching weld metal yield strength to parent metal yield strength
will not necessarily ensure that the weld metal tensile strength matches that of the parent metal. Where
the application requires matching tensile strengths, selection of consumables is made by reference to
column 3 of Table 1A or Table 1B.
Of note is that the mechanical properties of all-weld metal test specimens used to classify the tubular
cored electrodes will vary from those obtained in production joints because of the differences in welding
procedure such as electrode size, width of weave, welding position, and parent metal composition.
The classification in accordance with system A is mainly based on EN 758:1997. The classification in
accordance with system B is mainly based upon standards used around the Pacific Rim.
INTERNATIONAL STANDARD ISO 17632:2015(E)
Welding consumables — Tubular cored electrodes for gas
shielded and non-gas shielded metal arc welding of non-
alloy and fine grain steels — Classification
1 Scope
This International Standard specifies requirements for classification of tubular cored electrodes
with or without a gas shield for metal arc welding of non-alloy and fine grain steels in the as-welded
condition or in the post-weld heat-treated condition with a minimum yield strength of up to 500 MPa or
a minimum tensile strength of up to 570 MPa. One tubular cored electrode can be tested and classified
with different shielding gases, if any.
This International Standard is a combined specification providing classification utilizing a system
based upon the yield strength and the average impact energy of 47 J of all-weld metal or utilizing a
system based upon the tensile strength and the average impact energy of 27 J of all-weld metal.
1) Paragraphs and tables which carry the suffix letter “A” are applicable only to tubular cored
electrodes classified to the system based upon the yield strength and the average impact energy of
47 J of all-weld metal in accordance with this International Standard.
2) Paragraphs and tables which carry the suffix letter “B” are applicable only to tubular cored
electrodes classified to the system based upon the tensile strength and the average impact energy
of 27 J of all-weld metal in accordance with this International Standard.
3) Paragraphs and tables which have neither the suffix letter “A” nor the suffix letter “B” are applicable
to all tubular cored electrodes classified in accordance with this International Standard.
It is recognized that the operating characteristics of tubular cored electrodes can be modified by the use
of pulsed current, but for the purposes of this International Standard, pulsed current is not permitted
for determining the electrode classification.
2 Normative references
The following referenced documents, in whole or in part, are normatively referenced in this document
and are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 544, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of
product, dimensions, tolerances and markings
ISO 3690, Welding and allied processes — Determination of hydrogen content in arc weld metal
ISO 6847, Welding consumables — Deposition of a weld metal pad for chemical analysis
ISO 6947:2011, Welding and allied processes — Welding positions
ISO 13916, Welding — Guidance on the measurement of preheating temperature, interpass temperature
and preheat maintenance temperature
ISO 14175, Welding consumables — Gases and gas mixtures for fusion welding and allied processes
ISO 14344, Welding consumables — Procurement of filler materials and fluxes
ISO 15792-1:2000, Welding consumables — Test methods — Part 1: Test methods for all-weld metal test
specimens in steel, nickel and nickel alloys. Amended by ISO 15792-1:2000/Amd 1:2011
ISO 15792-2:2000, Welding consumables — Test methods — Part 2: Preparation of single-run and two-run
technique test specimens in steel
ISO 15792-3, Welding consumables — Test methods — Part 3: Classification testing of positional capacity
and root penetration of welding consumables in a fillet weld
ISO 80000-1:2009, Quantities and units — Part 1: General. Corrected by ISO 80000-1:2009/Cor 1:2011
3 Classification
Classification designations are based upon two approaches to indicate the tensile p
...
NORME ISO
INTERNATIONALE 17632
Deuxième édition
2015-11-15
Produits consommables pour le
soudage — Fils-électrodes fourrés
pour soudage à l’arc avec ou sans
gaz de protection des aciers non
alliés et des aciers à grains fins —
Classification
Welding consumables — Tubular cored electrodes for gas shielded
and non-gas shielded metal arc welding of non-alloy and fine grain
steels — Classification
Numéro de référence
©
ISO 2015
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Classification . 2
4 Symboles et exigences. 4
4.1 Symbole du produit et/ou du procédé . 4
4.2 Symbole pour les caractéristiques de traction du métal fondu hors dilution ou du
joint soudé . 4
4.2.1 Technique multipasse . 4
4.2.2 Technique monopasse . 5
4.3 Symbole pour les caractéristiques de résistance à la flexion par choc du métal
fondu hors dilution ou du joint soudé . 5
4.4 Symbole pour la composition chimique du métal fondu hors dilution . 7
4.5 Symbole pour le type de fourrage du fil-électrode ou pour les caractéristiques
d’usabilité du fil-électrode .10
4.6 Symbole pour le gaz de protection .10
4.7 Symbole pour la position de soudage .13
4.8 Symbole pour la teneur en hydrogène du métal déposé .13
4.9 Symbole pour la condition de traitement thermique après soudage pour le métal
fondu hors dilution .14
5 Essais mécaniques .14
5.1 Technique multipasse .14
5.1.1 Températures de préchauffage et entre passes . .14
5.1.2 Exigences relatives aux procédures pour les pièces d’essai en
soudage multipasse .16
5.1.3 Condition de traitement thermique après soudage.16
5.2 Technique monopasse .17
6 Analyse chimique .17
7 Méthode d’arrondissage .17
8 Essai pour soudures d’angle .17
9 Contre-essais .18
10 Conditions techniques de livraison .18
11 Exemples de désignation .19
Annexe A (informative) Systèmes de classification .23
Annexe B (informative) Description des types de fourrage dans le systèmede classification
d’après la limite d’élasticité etl’énergie de rupture moyenne de 47 J .26
Annexe C (informative) Description des types de caractéristiques d’usabilité dans le
systèmede classification d’après la résistance à la tractionet l’énergie de rupture
moyenne de 27 J .28
Annexe D (informative) Notes sur la teneur en hydrogène .31
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer
un engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à
l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes
de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos —
Informations supplémentaires.
Le comité chargé de l’élaboration du présent document est l’ISO/TC 44, Soudage et techniques connexes,
sous-comité SC 3, Produits consommables pour le soudage.
Cette deuxième édition annule et remplace la première édition (ISO 17632:2004), qui a fait l’objet d’une
révision technique.
Il convient d’adresser les demandes d’interprétation officielle de tout aspect de la présente Norme
internationale au secrétariat de l’ISO/TC 44/SC 3, via votre organisme national de normalisation; une
liste complète des organismes nationaux de normalisation peut être obtenue à l’adresse www.iso.org.
iv © ISO 2015 – Tous droits réservés
Introduction
La présente Norme internationale fournit un système de classification permettant de désigner les fils-
électrodes fourrés d’après la résistance à la traction, la résistance à la flexion par choc, la composition
chimique du métal fondu hors dilution, le type de fourrage, le gaz de protection et la position de soudage.
Le rapport entre la limite d’élasticité et la résistance à la traction du métal fondu est généralement plus
élevé que celui du métal de base. Il convient que les utilisateurs notent qu’une bonne correspondance des
limites d’élasticité du métal fondu et du métal de base ne garantit pas nécessairement que la résistance
à la traction du métal fondu correspondra à celle du métal de base. Ainsi, lorsque l’application exige
la correspondance de la résistance à la traction, le produit consommable est choisi en référence à la
colonne 3 du Tableau 1A ou du Tableau 1B.
Il convient de noter que les caractéristiques mécaniques des éprouvettes en métal fondu hors dilution
utilisées pour classifier les fils-électrodes diffèrent de celles obtenues sur des assemblages réalisés en
production, à cause des différences dans le mode opératoire de soudage telles que le diamètre du fil-
électrode, la largeur du balayage, la position de soudage et la composition chimique du métal de base.
La classification suivant le système A est principalement basée sur l’EN 758:1997. La classification
suivant le système B est principalement basée sur les normes utilisées dans la zone Pacifique.
NORME INTERNATIONALE ISO 17632:2015(F)
Produits consommables pour le soudage — Fils-électrodes
fourrés pour soudage à l’arc avec ou sans gaz de protection
des aciers non alliés et des aciers à grains fins —
Classification
1 Domaine d’application
La présente Norme internationale spécifie les exigences relatives à la classification des fils-électrodes
fourrés pour soudage à l’arc avec ou sans gaz de protection pour l’état brut de soudage ou pour l’état traité
thermiquement après soudage des aciers non alliés et des aciers à grains fins, ayant une limite d’élasticité
minimale pouvant atteindre 500 MPa ou une résistance à la traction minimale pouvant atteindre
570 MPa. Un fil-électrode peut, le cas échéant, être essayé et classifié avec différents gaz de protection.
La présente Norme internationale propose une spécification mixte permettant une classification
utilisant un système basé soit sur la limite d’élasticité et l’énergie de rupture moyenne de 47 J pour le
métal fondu hors dilution, soit sur la résistance à la traction et l’énergie de rupture moyenne de 27 J
pour le métal fondu hors dilution.
1) Les paragraphes et les tableaux qui portent le suffixe «A» ne sont applicables qu’aux fils-électrodes
classifiés d’après le système basé sur la limite d’élasticité et l’énergie de rupture moyenne de 47 J
pour le métal fondu hors dilution conformément à la présente Norme internationale.
2) Les paragraphes et les tableaux qui portent le suffixe «B» ne sont applicables qu’aux fils-électrodes
classifiés d’après le système basé sur la résistance à la traction et l’énergie de rupture moyenne de
27 J pour le métal fondu hors dilution conformément à la présente Norme internationale.
3) Les paragraphes et les tableaux qui ne portent ni le suffixe «A» ni le suffixe «B» sont applicables à
tous les fils-électrodes classifiés conformément à la présente Norme internationale.
Il est connu que les caractéristiques d’emploi d’un fil-électrode fourré peuvent être modifiées par
l’utilisation de courant pulsé mais, pour les besoins de la présente Norme internationale, l’utilisation de
courant pulsé pour la détermination de la classification d’un fil-électrode n’est pas autorisée.
2 Références normat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.