Gas cylinders — Refillable welded steel cylinders — Test pressure 60 bar and below

ISO 4706:2008 specifies the minimum requirements concerning material selection, design, construction and workmanship, procedure and test at manufacture of refillable welded-steel gas cylinders of a test pressure not greater than 60 bar, and of water capacities from 0,5 l up to and including 500 l exposed to extreme worldwide temperatures (-50 °C to +65 °C) used for compressed, liquefied or dissolved gases. Transportable large cylinders of water capacity above 150 l and up to 500 l may be manufactured and certified to ISO 4706 provided handling facilities are provided. ISO 4706 is primarily intended to be used for industrial gases other than Liquefied Petroleum Gas (LPG), but may also be applied for LPG. For specific LPG applications see ISO 22991.

Bouteilles à gaz — Bouteilles en acier soudées rechargeables — Pression d'essai de 60 bar et moins

General Information

Status
Withdrawn
Publication Date
07-Apr-2008
Current Stage
9599 - Withdrawal of International Standard
Completion Date
20-Sep-2023
Ref Project

Relations

Buy Standard

Standard
ISO 4706:2008 - Gas cylinders -- Refillable welded steel cylinders -- Test pressure 60 bar and below
English language
33 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 4706
First edition
2008-04-15
Corrected version
2008-07-01

Gas cylinders — Refillable welded steel
cylinders — Test pressure 60 bar and
below
Bouteilles à gaz — Bouteilles en acier soudées rechargeables —
Pression d'essai de 60 bar et moins




Reference number
ISO 4706:2008(E)
©
ISO 2008

---------------------- Page: 1 ----------------------
ISO 4706:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4706:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols. 2
4 Inspection and testing. 4
5 Materials . 4
6 Design . 5
7 Calculation of minimum wall thickness (sidewall and ends) . 6
8 Construction and workmanship. 11
9 Testing . 17
10 Acceptance criteria. 22
11 Technical requirements for new design type approval . 27
12 Markings . 28
13 Certificate . 28
Annex A (normative) Manufacturer's markings for LPG. 29
Annex B (informative) New design type approval certificate. 30
Annex C (informative) Acceptance certificate. 31
Bibliography . 33

© ISO 2008 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 4706:2008(E)
Foreword
ISO (the Internat
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.