ISO 3796:1999

Ships and marine technology — Clear openings for external single-leaf doors

This International Standard lays down standardized dimensions of clear openings for all types of external singleleaf doors, on board ships, for which coamings are required. These dimensions shall be used as nominal sizes for these doors of ships.

Navires et technologie maritime — Ouvertures libres pour les portes extérieures à un seul battant

General Information

• Status: Withdrawn
• Publication Date: 27-Oct-1999
• ICS: 47.020.10 - Hulls and their structure elements
• Technical Committee: ISO/TC 8/SC 8 - Ship design
• Drafting Committee: ISO/TC 8/SC 8 - Ship design
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 26-Oct-2023

Relations

• Revised: ISO 3796:2023 - Ships and marine technology — Clear openings for external single-leaf doors
• Effective Date: 06-Jun-2022
• Revises: ISO 3796:1976 - Shipbuilding — Clear openings through frames for external single-leaf doors
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3796
Second edition
1999-10-15
Ships and marine technology — Clear
openings for external single-leaf doors
Navires et technologie maritime — Ouvertures libres pour les portes
extérieures à un seul battant
Reference number
ISO 3796:1999(E)
©
ISO 1999

---------------------- Page: 1 ----------------------
ISO 3796:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3796:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 3796 was prepared by Technical
...