iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 50083-7:1999

(Main)

Cable networks for television signals, sound signals and interactive services -- Part 7: System performance

Cable networks for television signals, sound signals and interactive services -- Part 7: System performance

This standard is applicable to any cabled distribution system (including individual receiving systems) having a coaxial cable output and primarily intended for television and sound signals operating between about 30 MHz and 1750 MHz. This standard lays down the basic methods of measurement of the operational characteristics of cabled distribution systems having coaxial cable outputs in order to assess the performance of those systems and their performance limits. All requirements refer to the performance limits which shall be obtained between the input(s) to the headend or headends and any system outlet when terminated in a resistance equal to the nominal load impedance of the system, unless otherwise specified. Where system outlets are not used, the above applies at the susbcriber's end of the susbcriber's feeder. NOTE 1: Methods of measurement described in this standard are considered as basic. However, any equivalent method that ensures at least the same accuracy may be used. NOTE 2: If the system operator wishes to subdivide the system into a number of parts, the accumulation of degradations should not exceed the figures given below. NOTE 3: An extension of the frequency range to that from 5 MHz to 2050 MHz(3000 MHz) will be considered for future work

Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste -- Teil 7: Systemanforderungen

Réseaux de distribution par câbles pour signaux de télévision, signaux de radiodiffusion sonore et services interactifs -- Partie 7: Caractéristiques des systèmes

Cabled distribution systems for television and sound signals -- Part 7: System performance

General Information

Status
Withdrawn
Publication Date
31-Mar-1999
Withdrawal Date
12-Oct-2011
ICS
33.060.40 - Cabled distribution systems
Technical Committee
AVM - Audio, video and multimedia systems and equipment
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
12-Oct-2011
Due Date
04-Nov-2011
Completion Date
13-Oct-2011
Ref Project
EN 50083-7:1996 - Cable networks for television signals, sound signals and interactive services - Part 7: System performance

Relations

Amended By
SIST EN 50083-7:1999/A1:2001 - Cable networks for television signals, sound signals and interactive services -- Part 7: System performance
Effective Date
01-Mar-2001
Amended By
SIST EN 50083-7:1999/A1:2001 - Cable networks for television signals, sound signals and interactive services -- Part 7: System performance
Effective Date
29-Jan-2023
Amended By
SIST EN 50083-7:1999/A1:2001 - Cable networks for television signals, sound signals and interactive services -- Part 7: System performance
Effective Date
07-Jun-2022
Replaced By
SIST EN 60728-1:2008 - Cable networks for television signals, sound signals and interactive services -- Part 1: System performance of forward paths
Effective Date
01-Jul-2008

Buy Standard

EN 50083-7:1999EN 50083-7:1999
PreviousNext
Standard
EN 50083-7:1999
English language
73 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50083-7:1999
01-april-1999
Cabled distribution systems for television and sound signals -- Part 7: System
performance
Cable networks for television signals, sound signals and interactive services -- Part 7:
System performance
Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste -- Teil 7:
Systemanforderungen
Réseaux de distribution par câbles pour signaux de télévision, signaux de radiodiffusion
sonore et services interactifs -- Partie 7: Caractéristiques des systèmes
Ta slovenski standard je istoveten z: EN 50083-7:1996
ICS:
33.060.40 Kabelski razdelilni sistemi Cabled distribution systems
SIST EN 50083-7:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 2 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 3 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 4 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 5 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 6 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 7 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 8 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 9 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 10 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 11 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 12 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 13 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 14 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 15 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 16 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 17 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 18 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 19 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 20 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 21 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 22 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 23 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 24 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 25 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 26 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 27 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 28 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 29 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 30 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 31 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 32 ----------------------

SIST EN 50083-7:1999

---------------------- Page: 33 ----------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60728-115:2022(Main)
Cable networks for television signals, sound signals and interactive services - Part 115: In-building optical systems for broadcast signal transmissions (IEC 60728-115:2022)
EN IEC 60728-115:2022

This part of IEC 60728 is applicable to in-building optical transmission systems for broadcast signal transmission that consist of optical transmitter, optical amplifiers, splitters, V-ONUs, etc. These systems are primarily intended for television and sound signals using digital transmission technology. This document specifies the basic system parameters and methods of measurement for in-building optical distribution systems between building network interface (BNI) and home network interface (HNI) in order to assess the system performance and its performance limits.
This document is also applicable to broadcast signal transmission using a telecommunication network if it satisfies the requirements of optical section of this document. This document describes RF transmission for fully digitalized broadcast and narrowcast (limited area distribution of broadcast) signals over an FTTH network and introduces xPON system as a physical layer media. The detailed description of the physical layer is out of the scope of this document. The scope is limited to RF signal transmission over optical network, thus, it does not include IP transport technologies, such as IP Multicast and associate protocols.
This standard specifies the required system performance of all-optical building networks in order to connect with FTTH networks which are defined by IEC60728-113 and IEC60728-13-1. Use of In-building optical networks is very effective for saving cost (installation and maintenance) and enabling future network up-grades, especially in huge apartment buildings. In this document, the optical wavelengths and electrical frequency bands listed in Table 1 - and Table 2 - are considered to be used.
[Table 1 and Table 2]

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50083-2-4:2020(Main)
Cable networks for television signals, sound signals and interactive services - Part 2-4: Interference Mitigation Filters operating in the 700 MHz and 800 MHz bands for DTT reception
EN 50083-2-4:2019

This standard specifies the requirements for LTE filters that cover the 700 MHz band in addition to the 800 MHz band. These filters are to be used in individual and MATV antenna installations for reception of DTT signals when the 700 MHz band will be used by telecommunication services (LTE) in addition to the 800 MHz band.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60728-11:2018/A11:2019(Amendment)
Cable networks for television signals, sound signals and interactive services - Part 11: Safety
EN 60728-11:2017/A11:2018

contains Common Modifications to IEC 60728-11:2016 (the RD for EN 60728-11:2017) in response to the comments raised by the LVD New Approach Consultant in his negative assessment of IEC 60728-11.

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60728-113:2019/AC:2019(Corrigendum)
Cable networks for television signals, sound signals and interactive services - Part 113: Optical systems for broadcast signal transmissions loaded with digital channels only (IEC 60728-113:2018/COR1:2018)
EN IEC 60728-113:2018/AC:2018-12

IEC - Corrected version

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60728-113:2019(Main)
Cable networks for television signals, sound signals and interactive services - Part 113: Optical systems for broadcast signal transmissions loaded with digital channels only (IEC 60728-113:2018)
EN IEC 60728-113:2018

This part of IEC 60728 is applicable to optical transmission systems for broadcast signal
transmission that consist of headend equipment, optical transmission lines, in-house wirings
and system outlets. These systems are primarily intended for television and sound signals
using digital transmission technology. This document specifies the basic system parameters
and methods of measurement for optical distribution systems between headend equipment
and system outlets in order to assess the system performance and its performance limits.
In this document, the upper signal frequency is limited at about 1 000 MHz. For systems
requiring more bandwidth, refer to IEC 60728-13-1.
The purpose of this part of IEC 60728 is to describe the system specifications of FTTH (fibre
to the home) networks for digitally modulated broadcast signal transmission. This document is
also applicable to broadcast signal transmission using a telecommunication network if it
satisfies the optical portion of this document. This document describes RF transmission for
fully digitalized broadcast and narrowcast (limited area distribution of broadcast) signals over
FTTH, and introduces xPON system as a physical layer media. The detailed description of the
physical layer is out of the scope of this document. The scope is limited to RF signal
transmission over FTTH, thus, it does not include IP transport technologies, such as IP
Multicast and associate protocols.
Some interference descriptions between the telecommunication system and the broadcast
system are addressed in Clause 7.

  • Standard
    90 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CLC/TS 50083-2-3:2019(Main)
Cable networks for television signals, sound Signals and interactive services - Part 2-3: LTE (4G) Interference Mitigation Filters
CLC/TS 50083-2-3:2018

This Technical Specification provides requirements to passive filters intended to reduce RF interference from LTE Base Stations (LTE-BS) and LTE User Equipment (LTE-UE) to receiving equipment and cable distribution systems of broadcast DVB-T and DVB-T2 signals in the VHF and UHF bands. While primarily intended to be used with VHF/UHF DVB-T and DVB-T2 receivers and signal distribution systems, filters can also be useful for mitigation of interference to VHF FM or DAB radio.

  • Technical specification
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60728-3:2018(Main)
Cable networks for television signals, sound signals and interactive services - Part 3: Active wideband equipment for cable networks (TA 5) (IEC 60728-3:2017)
EN IEC 60728-3:2018

This part of IEC 60728 specifies the measuring methods, performance requirements and data
publication requirements for active wideband equipment of cable networks for television
signals, sound signals and interactive services.
This document
• applies to all amplifiers used in cable networks;
• covers the frequency range 5 MHz to 3 000 MHz;
NOTE The upper limit of 3 000 MHz is an example, but not a strict value.
• applies to one-way and two-way equipment;
• specifies the basic methods of measurement of the operational characteristics of the
active equipment in order to assess the performance of this equipment;
• identifies the performance specifications to be published by the manufacturers;
• states the minimum performance requirements of certain parameters.

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60728-101:2018/AC:2018(Corrigendum)
Cable networks for television signals, sound signals and interactive services - Part 101: System performance of forward paths loaded with digital channels only
EN 60728-101:2017/AC:2017-07
  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60728-11:2018(Main)
Cable networks for television signals, sound signals and interactive services - Part 11: Safety
EN 60728-11:2017

This part of IEC 60728 deals with the safety requirements applicable to fixed sited systems
and equipment. As far as applicable, it is also valid for mobile and temporarily installed
systems, for example, caravans.
Additional requirements may be applied, for example, referring to
• electrical installations of buildings and overhead lines,
• other telecommunication services distribution systems,
• water distribution systems,
• gas distribution systems,
• lightning systems.
This standard is intended to provide specifically for the safety of the system, personnel
working on it, subscribers and subscriber equipment. It deals only with safety aspects and is
not intended to define a standard for the protection of the equipment used in the system.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60728-101:2018(Main)
Cable networks for television signals, sound signals and interactive services - Part 101: System performance of forward paths with all-digital channels load (TA/5) (IEC 60728-101:2016)
EN 60728-101:2017

This part of IEC 60728 is applicable to any cable network (including individual receiving
systems) distributing only digital channels having in the forward path a coaxial cable output
and primarily intended for television and sound signals operating between about 30 MHz and
3 000 MHz.
This standard specifies the basic methods of measurement of the operational characteristics
of a cable network having coaxial cable outputs in order to assess the performance of these
systems and their performance limits.

  • Standard
    113 pages
    English language
    sale 10% off
    e-Library read for
    1 day