SIST EN 3077:2022
(Main)Aerospace series - Clamps worm drive - Technical specification
Aerospace series - Clamps worm drive - Technical specification
This document specifies the required characteristics, inspections, test methods, quality assurance,
qualification, acceptance and delivery conditions of clamps worm drive designed for use with suitable
rubber hoses to form joints in fluid system pipelines.
The clamps worm drive are intended to be used as specified in the product standards.
Luft- und Raumfahrt - Schellen mit Schneckentrieb - Technische Lieferbedingungen
Dieses Dokument legt die erforderlichen Eigenschaften, Inspektionen, Prüfverfahren, Qualitätssicherung, Qualifikation, Abnahme- und Lieferbedingungen von Schellen mit Schneckentrieb fest, die dafür ausgelegt sind, zusammen mit geeigneten Gummi-Schläuchen Verbindungen in fluidischen Rohrsystemen herzustellen.
Die Schellen mit Schneckentrieb sind für den in den Produktnormen angegebenen Gebrauch bestimmt.
Série aérospatiale - Colliers à vis tangente - Spécification technique
Le présent document spécifie les caractéristiques requises, les contrôles, les méthodes d’essai, l’assurance qualité, la qualification, la réception et les conditions de livraison des colliers à vis tangente conçus pour utilisation avec des tuyauteries en caoutchouc appropriées pour les raccordements de canalisations de systèmes de fluides.
Les colliers à vis tangente sont destinés à être utilisés comme spécifié dans les normes de produits.
Aeronavtika - Cevne objemke - Tehnična specifikacija
Ta dokument določa zahtevane značilnosti, preglede, preskusne metode, pogoje zagotavljanja kakovosti, kvalifikacije in sprejemljivosti, ter dobavne pogoje za cevne objemke, ki so zasnovane za uporabo z ustreznimi gumijastimi cevmi za oblikovanje spojev pri ocevju s tekočino. Cevne objemke so predvidene za uporabo v skladu z določili v standardih za izdelke.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 3077:2022
01-maj-2022
Aeronavtika - Cevne objemke - Tehnična specifikacija
Aerospace series - Clamps worm drive - Technical specification
Luft- und Raumfahrt - Schellen mit Schneckentrieb - Technische Lieferbedingungen
Série aérospatiale - Colliers à vis tangente - Spécification technique
Ta slovenski standard je istoveten z: EN 3077:2022
ICS:
49.030.99 Drugi vezni elementi Other fasteners
SIST EN 3077:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 3077:2022
---------------------- Page: 2 ----------------------
SIST EN 3077:2022
EN 3077
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 49.080
English Version
Aerospace series - Clamps worm drive - Technical
specification
Série aérospatiale - Colliers à vis tangente - Luft- und Raumfahrt - Schellen mit Schneckentrieb -
Spécification technique Technische Lieferbedingungen
This European Standard was approved by CEN on 17 January 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3077:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 3077:2022
EN 3077:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements, inspection and test methods . 4
5 Quality assurance . 6
5.1 Approval of manufacturer . 6
5.2 Product qualification . 6
6 Acceptance conditions . 6
6.1 Manufacturer’s responsibility . 6
6.2 Inspections and tests . 6
7 Packaging . 7
8 Acceptance test certificate . 8
Annex A (informative) Evolution sheet . 9
Bibliography . 10
2
---------------------- Page: 4 ----------------------
SIST EN 3077:2022
EN 3077:2022 (E)
European foreword
This document (EN 3077:2022) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
3
---------------------- Page: 5 ----------------------
SIST EN 3077:2022
EN 3077:2022 (E)
1 Scope
This document specifies the required characteristics, inspections, test methods, quality assurance,
qualification, acceptance and delivery conditions of clamps worm drive designed for use with suitable
rubber hoses to form joints in fluid system pipelines.
The clamps worm drive are intended to be used as specified in the product standards.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10204, Metallic products — Types of inspection documents
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• ISO Online browsing platform: availabl
...
SLOVENSKI STANDARD
oSIST prEN 3077:2020
01-september-2020
Aeronavtika - Cevne objemke - Tehnična specifikacija
Aerospace series - Clamps worm drive - Technical specification
Luft- und Raumfahrt - Schellen mit Schneckentrieb - Technische Lieferbedingungen
Série aérospatiale - Colliers à vis tangente - Spécification technique
Ta slovenski standard je istoveten z: prEN 3077
ICS:
49.030.99 Drugi vezni elementi Other fasteners
oSIST prEN 3077:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 3077:2020
---------------------- Page: 2 ----------------------
oSIST prEN 3077:2020
DRAFT
EUROPEAN STANDARD
prEN 3077
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2020
ICS
English Version
Aerospace series - Clamps worm drive - Technical
specification
Série aérospatiale - Colliers à vis tangente - Luft- und Raumfahrt - Schellen mit Schneckentrieb -
Spécification technique Technische Lieferbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 3077:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 3077:2020
prEN 3077:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements, inspection and test methods . 5
5 Quality assurance . 6
5.1 Approval of manufacturer . 6
5.2 Product qualification . 6
6 Acceptance conditions . 7
6.1 Manufacturer’s responsibility . 7
6.2 Inspections and tests . 7
7 Packaging . 8
8 Acceptance test certificate . 8
Annex A (informative) Evolution sheet . 9
Bibliography . 10
2
---------------------- Page: 4 ----------------------
oSIST prEN 3077:2020
prEN 3077:2020 (E)
European foreword
This document (prEN 3077:2020) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This document is currently submitted to the CEN Enquiry.
3
---------------------- Page: 5 ----------------------
oSIST prEN 3077:2020
prEN 3077:2020 (E)
1 Scope
This document specifies the required characteristics, inspections, test methods, quality assurance,
qualification, acceptance and delivery conditions of clamps worm drive designed for use with suitable
rubber hoses to form joints in fluid system pipelines.
The clamps worm drive are intended to be used as specified in the product standards.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10204, Metallic products - Types of inspection documents
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
clamp worm drive
band of material fitted with an adjustment device intended for use in conjunction with a suitable hose to
provide a pipe-to-pipe joint
3.2
batch
clamps of a particular size and material produced under essentially the same manufacturing condi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.