Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 17: Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive

The present document applies to the following radio equipment types:
Base Stations (also denoted as Access Network) for Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) compliant with TIA-1121.001 [4]. These radio equipment types are capable of operating in all or any part of the frequency bands given table 1-1.
  The present document covers requirements for UMB Base Stations. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2, which states that "….. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of Article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document.

Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Bazne postaje (BS), ponavljalniki (repetitorji) in uporabniška oprema (UE) za celična omrežja tretje generacije IMT-2000 - 17. del: Harmonizirani EN za IMT-2000, razvito CDMA z več nosilnimi frekvencami (“Multi-Carrier”) pri ultra mobilni širokopasovnosti (UMB) (BS), ki zajema bistvene zahteve člena 3.2 direktive R&TTE

Pričujoči dokument velja za naslednje vrste radijske opreme:
bazne postaje (označene tudi kot dostopno omrežje) za razviti CDMA z več nosilnimi frekvencami »Multi Carrier« pri ultramobilni širokopasovnosti (UMB), ki je v skladu z TIA-1121.001 [4]. Te vrste radijske opreme so zmožne delovanja v vseh ali katerem koli delu frekvenčnega pasu, kot so navedeni v tabeli 1-1.
Pričujoči dokument zajema zahteve za UMB bazne postaje. Pričujoči dokument je namenjen temu, da zajema določbe Direktive 1999/5/EC (direktive R&TTE ) [i.2], člena 3.2, ki navaja, da » … je radijska oprema narejena tako, da učinkovito izrablja spekter, razporejen za prizemne/vesoljske radiokomunikacije in orbitalne vire, tako da ne pride do škodljivega motenja«. Poleg pričujočega dokumenta, se ostali EN, ki določajo tehnične zahteve v skladu z bistvenimi zahtevami v drugih delih člena 3 direktive R&TTE [i.2] lahko uporabljajo za opremo znotraj področja uporabe pričujočega dokumenta.

General Information

Status
Published
Public Enquiry End Date
31-Jul-2009
Publication Date
08-Apr-2010
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Mar-2010
Due Date
22-May-2010
Completion Date
09-Apr-2010
Mandate

Buy Standard

Standard
EN 301 908-17 V4.2.1:2010
English language
44 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 301 908-17 V4.2.1 (2010-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 17: Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive
English language
44 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 908-17 V4.1.2 (2009-12) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 17: Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive
English language
43 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 908-17 V4.1.1 (2009-04) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 17: Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive
English language
44 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.OQL577(Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 17: Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-17 Version 4.2.1SIST EN 301 908-17 V4.2.1:2010en01-maj-2010SIST EN 301 908-17 V4.2.1:2010SLOVENSKI
STANDARD



SIST EN 301 908-17 V4.2.1:2010



ETSI EN 301 908-17 V4.2.1 (2010-03)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Base Stations (BS), Repeaters and User Equipment (UE)for IMT-2000 Third-Generation cellular networks;Part 17: Harmonized EN for IMT-2000,Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)covering the essential requirementsof article 3.2 of the R&TTE Directive SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)2
Reference DEN/ERM-TFES-002-17 Keywords 3G, 3GPP2, cdma2000, cellular, digital, IMT-2000, mobile, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 11 3.3 Abbreviations . 12 4 Technical requirements specifications . 13 4.1 Environmental profile . 13 4.2 Conformance requirements . 13 4.2.1 Introduction. 13 4.2.2 Transmitter conducted spurious emissions . 13 4.2.2.1 Definition . 13 4.2.2.2 Limits . 13 4.2.2.3 Conformance . 16 4.2.3 Maximum output power . 16 4.2.3.1 Definition . 16 4.2.3.2 Limits . 16 4.2.3.3 Conformance . 16 4.2.4 Inter-Base Station transmitter intermodulation . 16 4.2.4.1 Definition . 16 4.2.4.2 Limits . 16 4.2.4.3 Conformance . 16 4.2.5 Receiver conducted spurious emissions . 17 4.2.5.1 Definition . 17 4.2.5.2 Limits . 17 4.2.5.3 Conformance . 17 4.2.6 Receiver blocking characteristics . 17 4.2.6.1 Definition . 17 4.2.6.1.1 Test Parameters . 18 4.2.6.2 Limits . 18 4.2.6.3 Conformance . 18 4.2.7 Intermodulation spurious response attenuation . 18 4.2.7.1 Definition . 18 4.2.7.2 Limits . 20 4.2.7.3 Conformance . 20 4.2.8 Adjacent channel selectivity . 20 4.2.8.1 Definition . 20 4.2.8.1.1 Parameters . 21 4.2.8.2 Limits . 21 4.2.8.3 Conformance . 21 5 Testing for compliance with technical requirements . 22 5.1 Environmental conditions for testing . 22 5.1.1 Introduction. 22 5.1.2 Standard equipment under test . 22 5.1.2.1 Basic equipment . 22 5.1.2.2 Ancillary equipment . 22 5.2 Interpretation of the measurement results . 22 5.3 Essential radio test suites . 23 SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)4 5.3.1 Transmitter conducted spurious emissions . 23 5.3.2 Maximum output power . 23 5.3.3 Inter-Base Station transmitter intermodulation . 23 5.3.4 Receiver conducted spurious emissions . 24 5.3.5 Receiver blocking characteristics . 24 5.3.6 Intermodulation spurious response attenuation . 25 5.3.7 Adjacent channel selectivity . 25 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 26 Annex B (normative): Common Procedures . 28 B.1 Forward and Reverse Channels and Link Assignment Block (LAB) Assignments . 28 B.1.1 Reverse Link PER Measurement Test . 28 B.1.2 In-Channel Selectivity Test . 28 B.1.3 Transmitter Tests . 28 B.1.4 Emissions Test . 28 B.2 Session and Test Application Configurations . 28 B.2.1 Reverse Link PER Measurement . 28 B.2.2 In-Channel Selectivity Aggressor Configuration . 29 B.2.3 Emissions Tests . 29 Annex C (normative): Environmental profile . 30 C.1 Introduction . 30 C.2 General Requirements . 30 C.2.1 Temperature and Power Supply Voltage . 30 C.2.1.1 Method of Measurement . 30 C.2.2 High Humidity . 30 C.2.3 AC Power Line Conducted Emissions . 31 Annex D (normative): Standard test conditions . 32 D.1 Standard Equipment . 32 D.1.1 Basic Equipment . 32 D.1.2 Associated Equipment . 32 D.2 Standard Environmental Test Conditions . 32 D.3 Standard Conditions for the Primary Power Supply . 32 D.3.1 General . 32 D.3.2 Standard DC Test Voltage from Accumulator Batteries . 32 D.3.3 Standard AC Voltage and Frequency . 33 D.4 Standard Test Equipment . 33 D.4.1 Access Terminal Simulator . 33 D.4.2 AWGN Generator. 33 D.4.3 CW Generator . 33 D.4.4 Spectrum Analyzer . 34 D.4.5 Average Power Meter . 34 D.4.6 RF Output Load . 35 D.5 Functional System Setups . 35 D.5.1 Functional Block Diagrams . 35 D.6 Standard Duty Cycle . 38 D.7 Error Rates Measurement . 38 D.7.1 Frame Error Rates Measurement . 38 D.8 Confidence Limits . 38 Annex E (informative): The EN title in the official languages . 42 SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)5 Annex F (informative): Bibliography . 43 History . 44
SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive"). Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A. The present document is part 17 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below: Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)7 Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates Date of adoption of this EN: 19 February 2010 Date of latest announcement of this EN (doa): 31 May 2010 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 November 2010 Date of withdrawal of any conflicting National Standard (dow): 30 November 2011
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)8 1 Scope The present document applies to the following radio equipment types: • Base Stations (also denoted as Access Network) for Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) compliant with TIA-1121.001 [4]. These radio equipment types are capable of operating in all or any part of the frequency bands given table 1-1. Table 1-1: UMB Base Station operating bands Band Class (BC) Direction of transmission UMB Base Station operating bands 6 Transmit 2 110 MHz to 2 170 MHz Receive 1 920 MHz to 1 980 MHz 8 Transmit 1 805 MHz to 1 880 MHz Receive 1 710 MHz to 1 785 MHz 9 Transmit 925 MHz to 960 MHz Receive 880 MHz to 915 MHz 13 Transmit 2 620 MHz to 2 690 MHz Receive 2 500 MHz to 2 570 MHz
The present document covers requirements for UMB Base Stations. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2, which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of Article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • Non-specific reference may be made only to a complete document or a part thereof and only in the following cases: - if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document; - for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. SIST EN 301 908-17 V4.2.1:2010



ETSI ETSI EN 301 908-17 V4.2.1 (2010-03)9 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. [1] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements, covering the essential requirements of article 3.2 of the R&TTE Directive". [2] 3GPP2 C.S0088-0 V1.0, (March 2009): "Recommended Minimum Performance Standards for cdma2000 Ultra Mobile Broadband (UMB) Access Network" (to be published as TIA-1170). NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0088_v1.0_AN_MPS_for_UMB-090402.pdf. [3] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain". [4] TIA-1121.001 (December 2007): "Physical Layer for Ultra Mobile Broadband (UMB) Air Interface Specification". [5] 3GPP2 C.S0089-0 Version 1.0, (March 2009): "Recommended Minimum Performance Standards for cdma2000 Ultra Mobile Broadband Access Terminal" (to be published as TIA-1171). NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0089_v1.0_AT_MPS_for_UMB-090402.pdf. [6] 3GPP2 C.S0090-0 Version 1.0, (March 2009): "Test Application Specification for cdma2000 Ultra Mobile Broadband (UMB)" (to be published as TIA-1172). NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0090-0_v1.0_TAS_for_UMB-090402.pdf. 2.2 Informative references The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies. [i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. [i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (
...

ETSI EN 301 908-17 V4.2.1 (2010-03)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 17: Harmonized EN for IMT-2000,
Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-17 V4.2.1 (2010-03)



Reference
DEN/ERM-TFES-002-17
Keywords
3G, 3GPP2, cdma2000, cellular, digital, IMT-
2000, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-17 V4.2.1 (2010-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 11
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Environmental profile . 13
4.2 Conformance requirements . 13
4.2.1 Introduction. 13
4.2.2 Transmitter conducted spurious emissions . 13
4.2.2.1 Definition . 13
4.2.2.2 Limits . 13
4.2.2.3 Conformance . 16
4.2.3 Maximum output power . 16
4.2.3.1 Definition . 16
4.2.3.2 Limits . 16
4.2.3.3 Conformance . 16
4.2.4 Inter-Base Station transmitter intermodulation . 16
4.2.4.1 Definition . 16
4.2.4.2 Limits . 16
4.2.4.3 Conformance . 16
4.2.5 Receiver conducted spurious emissions . 17
4.2.5.1 Definition . 17
4.2.5.2 Limits . 17
4.2.5.3 Conformance . 17
4.2.6 Receiver blocking characteristics . 17
4.2.6.1 Definition . 17
4.2.6.1.1 Test Parameters . 18
4.2.6.2 Limits . 18
4.2.6.3 Conformance . 18
4.2.7 Intermodulation spurious response attenuation . 18
4.2.7.1 Definition . 18
4.2.7.2 Limits . 20
4.2.7.3 Conformance . 20
4.2.8 Adjacent channel selectivity . 20
4.2.8.1 Definition . 20
4.2.8.1.1 Parameters . 21
4.2.8.2 Limits . 21
4.2.8.3 Conformance . 21
5 Testing for compliance with technical requirements . 22
5.1 Environmental conditions for testing . 22
5.1.1 Introduction. 22
5.1.2 Standard equipment under test . 22
5.1.2.1 Basic equipment . 22
5.1.2.2 Ancillary equipment . 22
5.2 Interpretation of the measurement results . 22
5.3 Essential radio test suites . 23
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-17 V4.2.1 (2010-03)
5.3.1 Transmitter conducted spurious emissions . 23
5.3.2 Maximum output power . 23
5.3.3 Inter-Base Station transmitter intermodulation . 23
5.3.4 Receiver conducted spurious emissions . 24
5.3.5 Receiver blocking characteristics . 24
5.3.6 Intermodulation spurious response attenuation . 25
5.3.7 Adjacent channel selectivity . 25
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 26
Annex B (normative): Common Procedures . 28
B.1 Forward and Reverse Channels and Link Assignment Block (LAB) Assignments . 28
B.1.1 Reverse Link PER Measurement Test . 28
B.1.2 In-Channel Selectivity Test . 28
B.1.3 Transmitter Tests . 28
B.1.4 Emissions Test . 28
B.2 Session and Test Application Configurations . 28
B.2.1 Reverse Link PER Measurement . 28
B.2.2 In-Channel Selectivity Aggressor Configuration . 29
B.2.3 Emissions Tests . 29
Annex C (normative): Environmental profile . 30
C.1 Introduction . 30
C.2 General Requirements . 30
C.2.1 Temperature and Power Supply Voltage . 30
C.2.1.1 Method of Measurement . 30
C.2.2 High Humidity . 30
C.2.3 AC Power Line Conducted Emissions . 31
Annex D (normative): Standard test conditions . 32
D.1 Standard Equipment . . 32
D.1.1 Basic Equipment . 32
D.1.2 Associated Equipment . 32
D.2 Standard Environmental Test Conditions . 32
D.3 Standard Conditions for the Primary Power Supply . 32
D.3.1 General . 32
D.3.2 Standard DC Test Voltage from Accumulator Batteries . 32
D.3.3 Standard AC Voltage and Frequency . 33
D.4 Standard Test Equipment . 33
D.4.1 Access Terminal Simulator . 33
D.4.2 AWGN Generator. 33
D.4.3 CW Generator . 33
D.4.4 Spectrum Analyzer . 34
D.4.5 Average Power Meter . 34
D.4.6 RF Output Load . 35
D.5 Functional System Setups . 35
D.5.1 Functional Block Diagrams . 35
D.6 Standard Duty Cycle . . 38
D.7 Error Rates Measurement . 38
D.7.1 Frame Error Rates Measurement . 38
D.8 Confidence Limits . 38
Annex E (informative): The EN title in the official languages . 42
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-17 V4.2.1 (2010-03)
Annex F (informative): Bibliography . 43
History . 44

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-17 V4.2.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 17 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-17 V4.2.1 (2010-03)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB)
(BS) covering the essential requirements of article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 19 February 2010
Date of latest announcement of this EN (doa): 31 May 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2010
Date of withdrawal of any conflicting National Standard (dow): 30 November 2011

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-17 V4.2.1 (2010-03)
1 Scope
The present document applies to the following radio equipment types:
• Base Stations (also denoted as Access Network) for Evolved CDMA Multi-Carrier Ultra Mobile Broadband
(UMB) compliant with TIA-1121.001 [4].
These radio equipment types are capable of operating in all or any part of the frequency bands given table 1-1.
Table 1-1: UMB Base Station operating bands
Band Class (BC) Direction of transmission UMB Base Station operating bands
Transmit 2 110 MHz to 2 170 MHz
6
Receive 1 920 MHz to 1 980 MHz
Transmit 1 805 MHz to 1 880 MHz
8
Receive 1 710 MHz to 1 785 MHz
Transmit 925 MHz to 960 MHz
9
Receive 880 MHz to 915 MHz
Transmit 2 620 MHz to 2 690 MHz
13
Receive 2 500 MHz to 2 570 MHz

The present document covers requirements for UMB Base Stations.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of Article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 301 908-17 V4.2.1 (2010-03)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements,
covering the essential requirements of article 3.2 of the R&TTE Directive".
[2] 3GPP2 C.S0088-0 V1.0, (March 2009): "Recommended Minimum Performance Standards for
cdma2000 Ultra Mobile Broadband (UMB) Access Network" (to be published as TIA-1170).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0088_v1.0_AN_MPS_for_UMB-090402.pdf.
[3] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain".
[4] TIA-1121.001 (December 2007): "Physical Layer for Ultra Mobile Broadband (UMB) Air
Interface Specification".
[5] 3GPP2 C.S0089-0 Version 1.0, (March 2009): "Recommended Minimum Performance Standards
for cdma2000 Ultra Mobile Broadband Access Terminal" (to be published as TIA-1171).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0089_v1.0_AT_MPS_for_UMB-090402.pdf.
[6] 3GPP2 C.S0090-0 Version 1.0, (March 2009): "Test Application Specification for cdma2000 Ultra
Mobile Broadband (UMB)" (to be published as TIA-1172).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0090-0_v1.0_TAS_for_UMB-090402.pdf.
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of candidate Harmonized Standards for application under the R&TTE Directive".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the presen
...

Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 17: Harmonized EN for IMT-2000,
Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)



Reference
DEN/ERM-TFES-002-17
Keywords
3G, 3GPP2, cdma2000, cellular, digital,
IMT-2000, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 10
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Transmitter conducted spurious emissions . 12
4.2.2.1 Definition . 12
4.2.2.2 Limits . 12
4.2.2.3 Conformance . 15
4.2.3 Maximum output power . 15
4.2.3.1 Definition . 15
4.2.3.2 Limits . 15
4.2.3.3 Conformance . 15
4.2.4 Inter-Base Station transmitter intermodulation . 15
4.2.4.1 Definition . 15
4.2.4.2 Limits . 15
4.2.4.3 Conformance . 15
4.2.5 Receiver conducted spurious emissions . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver blocking characteristics . 16
4.2.6.1 Definition . 16
4.2.6.1.1 Test Parameters . 17
4.2.6.2 Limits . 17
4.2.6.3 Conformance . 17
4.2.7 Intermodulation spurious response attenuation . 17
4.2.7.1 Definition . 17
4.2.7.2 Limits . 19
4.2.7.3 Conformance . 19
4.2.8 Adjacent channel selectivity . 19
4.2.8.1 Definition . 19
4.2.8.1.1 Parameters . 20
4.2.8.2 Limits . 20
4.2.8.3 Conformance . 20
5 Testing for compliance with technical requirements . 21
5.1 Environmental conditions for testing . 21
5.1.1 Introduction. 21
5.1.2 Standard equipment under test . 21
5.1.2.1 Basic equipment . 21
5.1.2.2 Ancillary equipment . 21
5.2 Interpretation of the measurement results . 21
5.3 Essential radio test suites . 22
5.3.1 Transmitter conducted spurious emissions . 22
5.3.2 Maximum output power . 22
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)
5.3.3 Inter-Base Station transmitter intermodulation . 22
5.3.4 Receiver conducted spurious emissions . 23
5.3.5 Receiver blocking characteristics . 23
5.3.6 Intermodulation spurious response attenuation . 24
5.3.7 Adjacent channel selectivity . 24
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 25
Annex B (normative): Common Procedures . 27
B.1 Forward and Reverse Channels and Link Assignment Block (LAB) Assignments . 27
B.1.1 Reverse Link PER Measurement Test . 27
B.1.2 In-Channel Selectivity Test . 27
B.1.3 Transmitter Tests . 27
B.1.4 Emissions Test . 27
B.2 Session and Test Application Configurations . 27
B.2.1 Reverse Link PER Measurement . 27
B.2.2 In-Channel Selectivity Aggressor Configuration . 28
B.2.3 Emissions Tests . 28
Annex C (normative): Environmental profile . 29
C.1 Introduction . 29
C.2 General Requirements . 29
C.2.1 Temperature and Power Supply Voltage . 29
C.2.1.1 Method of Measurement . 29
C.2.2 High Humidity . 29
C.2.3 AC Power Line Conducted Emissions . 30
Annex D (normative): Standard test conditions . 31
D.1 Standard Equipment . . 31
D.1.1 Basic Equipment . 31
D.1.2 Associated Equipment . 31
D.2 Standard Environmental Test Conditions . 31
D.3 Standard Conditions for the Primary Power Supply . 31
D.3.1 General . 31
D.3.2 Standard DC Test Voltage from Accumulator Batteries . 31
D.3.3 Standard AC Voltage and Frequency . 32
D.4 Standard Test Equipment . 32
D.4.1 Access Terminal Simulator . 32
D.4.2 AWGN Generator. 32
D.4.3 CW Generator . 32
D.4.4 Spectrum Analyzer . 33
D.4.5 Average Power Meter . 33
D.4.6 RF Output Load . 34
D.5 Functional System Setups . 34
D.5.1 Functional Block Diagrams . 34
D.6 Standard Duty Cycle . . 37
D.7 Error Rates Measurement . 37
D.7.1 Frame Error Rates Measurement . 37
D.8 Confidence Limits . 37
Annex E (informative): The EN title in the official languages . 41
Annex F (informative): Bibliography . 42
History . 43

ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 17 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB)
(BS) covering the essential requirements of article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)
1 Scope
The present document applies to the following radio equipment types:
• Base Stations (also denoted as Access Network) for Evolved CDMA Multi-Carrier Ultra Mobile Broadband
(UMB) compliant with TIA-1121.001 [4].
These radio equipment types are capable of operating in all or any part of the frequency bands given table 1-1.
Table 1-1: UMB Base Station operating bands
Band Class (BC) Direction of transmission UMB Base Station operating bands
Transmit 2 110 MHz to 2 170 MHz
6
Receive 1 920 MHz to 1 980 MHz
Transmit 1 805 MHz to 1 880 MHz
8
Receive 1 710 MHz to 1 785 MHz
Transmit 925 MHz to 960 MHz
9
Receive 880 MHz to 915 MHz
Transmit 2 620 MHz to 2 690 MHz
13
Receive 2 500 MHz to 2 570 MHz

The present document covers requirements for UMB Base Stations.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of Article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 908-17 V4.1.2 (2009-12)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements,
covering the essential requirements of article 3.2 of the R&TTE Directive".
[2] 3GPP2 C.S0088-0 V1.0, (March 2009): "Recommended Minimum Performance Standards for
cdma2000 Ultra Mobile Broadband (UMB) Access Network" (to be published as TIA-1170).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0088_v1.0_AN_MPS_for_UMB-090402.pdf.
[3] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain".
[4] TIA-1121.001 (December 2007): "Physical Layer for Ultra Mobile Broadband (UMB) Air
Interface Specification".
[5] 3GPP2 C.S0089-0 Version 1.0, (March 2009): "Recommended Minimum Performance Standards
for cdma2000 Ultra Mobile Broadband Access Terminal" (to be published as TIA-1171).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0089_v1.0_AT_MPS_for_UMB-090402.pdf.
[6] 3GPP2 C.S0090-0 Version 1.0, (March 2009): "Test Application Specification for cdma2000 Ultra
Mobile Broadband (UMB)" (to be published as TIA-1172).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0090-0_v1.0_TAS_for_UMB-090402.pdf.
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of candidate Harmonized Standards for application under the R&TTE Directive".
3 Defini
...

Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 17: Harmonized EN for IMT-2000,
Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)



Reference
DEN/ERM-TFES-002-17
Keywords
3G, 3GPP2, cdma2000, cellular, digital,
IMT-2000, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
Contents
Intellectual Property Rights.6
Foreword.6
Introduction .7
1 Scope.8
2 References.8
2.1 Normative references.9
2.2 Informative references.9
3 Definitions, symbols and abbreviations .9
3.1 Definitions.9
3.2 Symbols.11
3.3 Abbreviations.12
4 Technical requirements specifications .12
4.1 Environmental profile.12
4.2 Conformance requirements.13
4.2.1 Introduction.13
4.2.2 Transmitter conducted spurious emissions .13
4.2.2.1 Definition.13
4.2.2.2 Limits.13
4.2.2.3 Conformance.16
4.2.3 Maximum output power.16
4.2.3.1 Definition.16
4.2.3.2 Limits.16
4.2.3.3 Conformance.16
4.2.4 Inter-base station transmitter intermodulation .16
4.2.4.1 Definition.16
4.2.4.2 Limits.16
4.2.4.3 Conformance.16
4.2.5 Receiver conducted spurious emissions.17
4.2.5.1 Definition.17
4.2.5.2 Limits.17
4.2.5.3 Conformance.17
4.2.6 Receiver blocking characteristics .17
4.2.6.1 Definition.17
4.2.6.1.1 Test Parameters.18
4.2.6.2 Limits.18
4.2.6.3 Conformance.18
4.2.7 Intermodulation spurious response attenuation.18
4.2.7.1 Definition.18
4.2.7.2 Limits.20
4.2.7.3 Conformance.20
4.2.8 Adjacent channel selectivity .20
4.2.8.1 Definition.20
4.2.8.1.1 Parameters.21
4.2.8.2 Limits.21
4.2.8.3 Conformance.21
5 Testing for compliance with technical requirements.22
5.1 Environmental conditions for testing .22
5.1.1 Introduction.22
5.1.2 Standard equipment under test.22
5.1.2.1 Basic equipment.22
5.1.2.2 Ancillary equipment.22
5.2 Interpretation of the measurement results .22
5.3 Essential radio test suites.23
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
5.3.1 Transmitter conducted spurious emissions .23
5.3.2 Maximum output power.23
5.3.3 Inter-base station transmitter intermodulation .23
5.3.4 Receiver conducted spurious emissions.24
5.3.5 Receiver blocking characteristics .24
5.3.6 Intermodulation spurious response attenuation.25
5.3.7 Adjacent channel selectivity .25
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT).26
Annex B (normative): Common Procedures .28
B.1 Forward and Reverse Channels and Link Assignment Block (LAB) Assignments.28
B.1.1 Reverse Link PER Measurement Test.28
B.1.2 In-Channel Selectivity Test .28
B.1.3 Transmitter Tests.28
B.1.4 Emissions Test.28
B.2 Session and Test Application Configurations .28
B.2.1 Reverse Link PER Measurement.28
B.2.2 In-Channel Selectivity Aggressor Configuration .29
B.2.3 Emissions Tests.29
Annex C (normative): Environmental profile .30
C.1 Introduction.30
C.2 General Requirements .30
C.2.1 Temperature and Power Supply Voltage.30
C.2.1.1 Method of Measurement.30
C.2.2 High Humidity.30
C.2.3 AC Power Line Conducted Emissions .31
Annex D (normative): Standard test conditions.32
D.1 Standard Equipment.32
D.1.1 Basic Equipment.32
D.1.2 Associated Equipment.32
D.2 Standard Environmental Test Conditions.32
D.3 Standard Conditions for the Primary Power Supply .32
D.3.1 General.32
D.3.2 Standard DC Test Voltage from Accumulator Batteries .32
D.3.3 Standard AC Voltage and Frequency .33
D.4 Standard Test Equipment.33
D.4.1 Access Terminal Simulator .33
D.4.2 AWGN Generator.33
D.4.3 CW Generator.33
D.4.4 Spectrum Analyzer.34
D.4.5 Average Power Meter.34
D.4.6 RF Output Load.35
D.5 Functional System Setups .35
D.5.1 Functional Block Diagrams.35
D.6 Standard Duty Cycle .38
D.7 Error Rates Measurement.38
D.7.1 Frame Error Rates Measurement.38
D.8 Confidence Limits.38
Annex E (informative): The EN title in the official languages .42
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
Annex F (informative): Bibliography.43
History .44

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 17 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB)
(BS) covering the essential requirements of article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
1 Scope
The present document applies to the following radio equipment types:
• Base Stations (also denoted as Access Network) for Evolved CDMA Multi-Carrier Ultra Mobile Broadband
(UMB) compliant with TIA-1121 [4].
These radio equipment types are capable of operating in all or any part of the frequency bands given table 1-1.
Table 1-1: UMB Base Station operating bands
Band Class (BC) Direction of transmission UMB Base Station operating bands
Transmit 2 110 MHz to 2 170 MHz
6
Receive 1 920 MHz to 1 980 MHz
Transmit 1 805 MHz to 1 880 MHz
8
Receive 1 710 MHz to 1 785 MHz
Transmit 925 MHz to 960 MHz
9
Receive 880 MHz to 915 MHz
Transmit 2 620 MHz to 2 690 MHz
13
Receive 2 500 MHz to 2 570 MHz

The present document covers requirements for UMB Base Stations.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of Article 3 of the R&TTE Directive may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 908-17 V4.1.1 (2009-04)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 301 908-1 (V4.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements,
covering the essential requirements of article 3.2 of the R&TTE Directive".
[2] 3GPP2 C.S0088-0 V1.0 (March 2009): "Recommended Minimum Performance Standards for
cdma2000 Ultra Mobile Broadband Access Network" (to be published as TIA-1170).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0088_v1.0_AN_MPS_for_UMB-090402.pdf.
[3] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain".
[4] TIA-1121 (2009): "Physical Layer for Ultra Mobile Broadband Air Interface Specification" (see
alternatively: 3GPP2 C. S0084-001-0 V3.0, August 2008).
[5] 3GPP2 C.S0089, Version 1.0, (March 2009): "Recommended Minimum Performance Standards
for cdma2000 Ultra Mobile Broadband Access Terminal" (to be published as TIA-1171).
NOTE: Available at ftp://ftp.3gpp2.org/TSGC/Working/2009/2009-03-NewOrleans/TSG-C-2009-03-
New%20Orleans/Plenary/C00-20090330-116a%20C.S0089%20PPV.zip.
[6] 3GPP2 C.S0090, Version 1.0, (March 2009): "Test Application Specification for cdma2000 Ultra
Mobile Broadband (UMB)" (to be published as TIA-1172).
NOTE: Available at http://www.3gpp2.org/Public_html/specs/C.S0090-0_v1.0_TAS_for_UMB-090402.pdf.
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of candidate Harmonized Standards for application under the R&TTE Directive".
3 Definitions, symbols
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.