SIST EN 300 328 V2.1.1:2017
(Main)Wideband transmission systems - Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
Wideband transmission systems - Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
The present document applies to Wide Band Data Transmission equipment.
The present document also describes spectrum access requirements to facilitate spectrum sharing with other equipment.
Wide Band Data Transmission equipment covered by the present document is operated in accordance with the ERC
Recommendation 70-03 [i.6], annex 3 or Commission Decision 2006/771/EC [i.7] (and its amendments).
Equipment using Ultra Wide Band (UWB) technology is not covered by the present document.
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
Širokopasovni prenosni sistemi - Oprema za prenos podatkov v frekvenčnem pasu 2,4 GHz ISM, ki uporablja širokopasovne modulacijske tehnike - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument se uporablja za opremo za širokopasovni prenos podatkov.
Ta dokument opisuje tudi zahteve za dostop do spektra, ki omogočajo lažje deljenje spektra z drugo opremo.
Oprema za širokopasovni prenos podatkov, ki je obravnavana v tem dokumentu, se uporablja v skladu z dodatkom 3 k priporočilu ERC 70-03 [i.6] ali odločbo Komisije 2006/771/ES [i.7] (in njenimi spremembami).
Ta dokument ne obravnava opreme, ki uporablja ultra širokopasovno (UWB) tehnologijo.
Ta dokument vključuje zahteve, s katerimi se dokazuje, da radijska oprema učinkovito uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.UPRQL]LUDQL(8Wideband transmission systems - Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 300 328 V2.1.1 (2016-11)SIST EN 300 328 V2.1.1:2017en01-januar-2017SIST EN 300 328 V2.1.1:2017SLOVENSKI
STANDARD
SIST EN 300 328 V2.1.1:2017
ETSI EN 300 328 V2.1.1 (2016-11) Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 300 328 V2.1.1:2017
ETSI ETSI EN 300 328 V2.1.1 (2016-11) 2
Reference REN/ERM-TG11-011 Keywords broadband, data, harmonised standard, ISM, LAN, mobile, radio, regulation, spread spectrum, SRD, testing, transmission, UHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 328 V2.1.1:2017
ETSI ETSI EN 300 328 V2.1.1 (2016-11) 3 Contents Intellectual Property Rights . 9 Foreword . 9 Modal verbs terminology . 9 Introduction . 9 1 Scope . 10 2 References . 10 2.1 Normative references . 10 2.2 Informative references . 10 3 Definitions, symbols and abbreviations . 11 3.1 Definitions . 11 3.2 Symbols . 13 3.3 Abbreviations . 14 4 Technical requirements specifications . 15 4.1 Environmental profile . 15 4.2 Equipment types . 15 4.2.1 Modulation types . 15 4.2.2 Adaptive and non-adaptive equipment . 15 4.2.3 Receiver categories . 15 4.2.3.1 Introduction . 15 4.2.3.2 Categorization . 15 4.2.3.2.1 Receiver category 1 . 15 4.2.3.2.2 Receiver category 2 . 16 4.2.3.2.3 Receiver category 3 . 16 4.3 Conformance requirements . 16 4.3.1 Requirements for Frequency Hopping equipment . 16 4.3.1.1 Introduction . 16 4.3.1.2 RF output power . 16 4.3.1.2.1 Applicability . 16 4.3.1.2.2 Definition. 16 4.3.1.2.3 Limit . 16 4.3.1.2.4 Conformance . 16 4.3.1.3 Duty Cycle, Tx-sequence, Tx-gap . 16 4.3.1.3.1 Applicability . 16 4.3.1.3.2 Definition. 17 4.3.1.3.3 Limit . 17 4.3.1.3.4 Conformance . 17 4.3.1.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 17 4.3.1.4.1 Applicability . 17 4.3.1.4.2 Definition. 17 4.3.1.4.3 Limit . 17 4.3.1.4.4 Other Requirements . 18 4.3.1.4.5 Conformance . 18 4.3.1.5 Hopping Frequency Separation . 19 4.3.1.5.1 Applicability . 19 4.3.1.5.2 Definition. 19 4.3.1.5.3 Limit . 19 4.3.1.5.4 Conformance . 19 4.3.1.6 Medium Utilization (MU) factor . 19 4.3.1.6.1 Applicability . 19 4.3.1.6.2 Definition. 20 4.3.1.6.3 Limit . 20 4.3.1.6.4 Conformance . 20 4.3.1.7 Adaptivity (Adaptive Frequency Hopping) . 20 4.3.1.7.1 Applicability . 20 SIST EN 300 328 V2.1.1:2017
ETSI ETSI EN 300 328 V2.1.1 (2016-11) 4 4.3.1.7.2 Adaptive Frequency Hopping using LBT based DAA . 20 4.3.1.7.3 Adaptive Frequency Hopping using other forms of DAA (non-LBT based) . 22 4.3.1.7.4 Short Control Signalling Transmissions . 23 4.3.1.8 Occupied Channel Bandwidth . 23 4.3.1.8.1 Applicability . 23 4.3.1.8.2 Definition. 24 4.3.1.8.3 Limits . 24 4.3.1.8.4 Conformance . 24 4.3.1.9 Transmitter unwanted emissions in the out-of-band domain . 24 4.3.1.9.1 Applicability . 24 4.3.1.9.2 Definition. 24 4.3.1.9.3 Limit . 24 4.3.1.9.4 Conformance . 24 4.3.1.10 Transmitter unwanted emissions in the spurious domain . 25 4.3.1.10.1 Applicability . 25 4.3.1.10.2 Definition. 25 4.3.1.10.3 Limit . 25 4.3.1.10.4 Conformance . 25 4.3.1.11 Receiver spurious emissions . 25 4.3.1.11.1 Applicability . 25 4.3.1.11.2 Definition. 25 4.3.1.11.3 Limit . 25 4.3.1.11.4 Conformance . 26 4.3.1.12 Receiver Blocking . 26 4.3.1.12.1 Applicability . 26 4.3.1.12.2 Definition. 26 4.3.1.12.3 Performance Criteria . 26 4.3.1.12.4 Limits . 26 4.3.1.12.5 Conformance . 27 4.3.1.13 Geo-location capability . 27 4.3.1.13.1 Applicability . 27 4.3.1.13.2 Definition. 27 4.3.1.13.3 Requirements . 28 4.3.2 Requirements for other types of Wide Band modulation . 28 4.3.2.1 Introduction . 28 4.3.2.2 RF output power . 28 4.3.2.2.1 Applicability . 28 4.3.2.2.2 Definition. 28 4.3.2.2.3 Limit . 28 4.3.2.2.4 Conformance . 28 4.3.2.3 Power Spectral Density . 28 4.3.2.3.1 Applicability . 28 4.3.2.3.2 Definition. 28 4.3.2.3.3 Limit . 29 4.3.2.3.4 Conformance . 29 4.3.2.4 Duty Cycle, Tx-sequence, Tx-gap . 29 4.3.2.4.1 Applicability . 29 4.3.2.4.2 Definition. 29 4.3.2.4.3 Limit . 29 4.3.2.4.4 Conformance . 29 4.3.2.5 Medium Utilization (MU) factor . 29 4.3.2.5.1 Applicability . 29 4.3.2.5.2 Definition. 29 4.3.2.5.3 Limit . 30 4.3.2.5.4 Conformance . 30 4.3.2.6 Adaptivity (adaptive equipment using modulations other than FHSS) . 30 4.3.2.6.1 Applicability . 30 4.3.2.6.2 Non-LBT based Detect and Avoid . 30 4.3.2.6.3 LBT based Detect and Avoid . 31 4.3.2.6.4 Short Control Signalling Transmissions . 34 4.3.2.7 Occupied Channel Bandwidth . 34 4.3.2.7.1 Applicability . 34 SIST EN 300 328 V2.1.1:2017
ETSI ETSI EN 300 328 V2.1.1 (2016-11) 5 4.3.2.7.2 Definition. 35 4.3.2.7.3 Limits . 35 4.3.2.7.4 Conformance . 35 4.3.2.8 Transmitter unwanted emissions in the out-of-band domain . 35 4.3.2.8.1 Applicability . 35 4.3.2.8.2 Definition. 35 4.3.2.8.3 Limit . 35 4.3.2.8.4 Conformance . 35 4.3.2.9 Transmitter unwanted emissions in the spurious domain . 36 4.3.2.9.1 Applicability . 36 4.3.2.9.2 Definition. 36 4.3.2.9.3 Limit . 36 4.3.2.9.4 Conformance . 36 4.3.2.10 Receiver spurious emissions . 36 4.3.2.10.1 Applicability . 36 4.3.2.10.2 Definition. 36 4.3.2.10.3 Limit . 36 4.3.2.10.4 Conformance . 37 4.3.2.11 Receiver Blocking . 37 4.3.2.11.1 Applicability . 37 4.3.2.11.2 Definition. 37 4.3.2.11.3 Performance Criteria . 37 4.3.2.11.4 Limits . 37 4.3.2.11.5 Conformance . 38 4.3.2.12 Geo-location capability . 38 4.3.2.12.1 Applicability . 38 4.3.2.12.2 Definition. 38 4.3.2.12.3 Requirements . 39 5 Testing for compliance with technical requirements . 39 5.1 Environmental conditions for testing . 39 5.1.1 Introduction. 39 5.1.2 Normal test conditions . 39 5.1.2.1 Normal temperature and humidity . 39 5.1.2.2 Normal power source . 39 5.1.3 Extreme test conditions . 39 5.2 Interpretation of the measurement results . 39 5.3 Definition of other test conditions . 40 5.3.1 Test mode. 40 5.3.2 Antennas and transmit operating modes . 40 5.3.2.1 Integrated and dedicated antennas . 40 5.3.2.2 Smart antenna systems and related operating modes . 41 5.3.2.2.1 Introduction . 41 5.3.2.2.2 Operating mode 1 (single antenna) . 41 5.3.2.2.3 Operating mode 2 (multiple antennas, no beamforming) . 41 5.3.2.2.4 Operating mode 3 (multiple antennas, with beamforming) . 41 5.3.2.3 Configuration for testing . 41 5.3.3 Adaptive and Non-adaptive equipment. 41 5.3.4 Presentation of equipment . 41 5.3.4.1 Introduction . 41 5.3.4.2 Testing of stand-alone equipment . 41 5.3.4.3 Testing of host connected equipment and plug-in radio equipment . 42 5.3.4.3.1 Introduction . 42 5.3.4.3.2 The use of a host or test jig for testing plug-in radio equipment . 42 5.3.4.3.3 Testing of combinations .
...
ETSI EN 300 328 V2.1.1 (2016-11)
HARMONISED EUROPEAN STANDARD
Wideband transmission systems;
Data transmission equipment operating
in the 2,4 GHz ISM band and
using wide band modulation techniques;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 300 328 V2.1.1 (2016-11)
Reference
REN/ERM-TG11-011
Keywords
broadband, data, harmonised standard, ISM,
LAN, mobile, radio, regulation, spread spectrum,
SRD, testing, transmission, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 328 V2.1.1 (2016-11)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 9
Introduction . 9
1 Scope . 10
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 Environmental profile . 15
4.2 Equipment types . 15
4.2.1 Modulation types . 15
4.2.2 Adaptive and non-adaptive equipment . 15
4.2.3 Receiver categories . 15
4.2.3.1 Introduction . 15
4.2.3.2 Categorization . 15
4.2.3.2.1 Receiver category 1 . 15
4.2.3.2.2 Receiver category 2 . 16
4.2.3.2.3 Receiver category 3 . 16
4.3 Conformance requirements . 16
4.3.1 Requirements for Frequency Hopping equipment . 16
4.3.1.1 Introduction . 16
4.3.1.2 RF output power . 16
4.3.1.2.1 Applicability . 16
4.3.1.2.2 Definition. 16
4.3.1.2.3 Limit . 16
4.3.1.2.4 Conformance . 16
4.3.1.3 Duty Cycle, Tx-sequence, Tx-gap . 16
4.3.1.3.1 Applicability . 16
4.3.1.3.2 Definition. 17
4.3.1.3.3 Limit . 17
4.3.1.3.4 Conformance . 17
4.3.1.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 17
4.3.1.4.1 Applicability . 17
4.3.1.4.2 Definition. 17
4.3.1.4.3 Limit . 17
4.3.1.4.4 Other Requirements . 18
4.3.1.4.5 Conformance . 18
4.3.1.5 Hopping Frequency Separation . 19
4.3.1.5.1 Applicability . 19
4.3.1.5.2 Definition. 19
4.3.1.5.3 Limit . 19
4.3.1.5.4 Conformance . 19
4.3.1.6 Medium Utilization (MU) factor . 19
4.3.1.6.1 Applicability . 19
4.3.1.6.2 Definition. 20
4.3.1.6.3 Limit . 20
4.3.1.6.4 Conformance . 20
4.3.1.7 Adaptivity (Adaptive Frequency Hopping) . 20
4.3.1.7.1 Applicability . 20
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 328 V2.1.1 (2016-11)
4.3.1.7.2 Adaptive Frequency Hopping using LBT based DAA . 20
4.3.1.7.3 Adaptive Frequency Hopping using other forms of DAA (non-LBT based) . 22
4.3.1.7.4 Short Control Signalling Transmissions . 23
4.3.1.8 Occupied Channel Bandwidth . 23
4.3.1.8.1 Applicability . 23
4.3.1.8.2 Definition. 24
4.3.1.8.3 Limits . 24
4.3.1.8.4 Conformance . 24
4.3.1.9 Transmitter unwanted emissions in the out-of-band domain . 24
4.3.1.9.1 Applicability . 24
4.3.1.9.2 Definition. 24
4.3.1.9.3 Limit . 24
4.3.1.9.4 Conformance . 24
4.3.1.10 Transmitter unwanted emissions in the spurious domain . 25
4.3.1.10.1 Applicability . 25
4.3.1.10.2 Definition. 25
4.3.1.10.3 Limit . 25
4.3.1.10.4 Conformance . 25
4.3.1.11 Receiver spurious emissions . 25
4.3.1.11.1 Applicability . 25
4.3.1.11.2 Definition. 25
4.3.1.11.3 Limit . 25
4.3.1.11.4 Conformance . 26
4.3.1.12 Receiver Blocking . 26
4.3.1.12.1 Applicability . 26
4.3.1.12.2 Definition. 26
4.3.1.12.3 Performance Criteria . 26
4.3.1.12.4 Limits . 26
4.3.1.12.5 Conformance . 27
4.3.1.13 Geo-location capability . 27
4.3.1.13.1 Applicability . 27
4.3.1.13.2 Definition. 27
4.3.1.13.3 Requirements . 28
4.3.2 Requirements for other types of Wide Band modulation . 28
4.3.2.1 Introduction . 28
4.3.2.2 RF output power . 28
4.3.2.2.1 Applicability . 28
4.3.2.2.2 Definition. 28
4.3.2.2.3 Limit . 28
4.3.2.2.4 Conformance . 28
4.3.2.3 Power Spectral Density . 28
4.3.2.3.1 Applicability . 28
4.3.2.3.2 Definition. 28
4.3.2.3.3 Limit . 29
4.3.2.3.4 Conformance . 29
4.3.2.4 Duty Cycle, Tx-sequence, Tx-gap . 29
4.3.2.4.1 Applicability . 29
4.3.2.4.2 Definition. 29
4.3.2.4.3 Limit . 29
4.3.2.4.4 Conformance . 29
4.3.2.5 Medium Utilization (MU) factor . 29
4.3.2.5.1 Applicability . 29
4.3.2.5.2 Definition. 29
4.3.2.5.3 Limit . 30
4.3.2.5.4 Conformance . 30
4.3.2.6 Adaptivity (adaptive equipment using modulations other than FHSS) . 30
4.3.2.6.1 Applicability . 30
4.3.2.6.2 Non-LBT based Detect and Avoid . 30
4.3.2.6.3 LBT based Detect and Avoid . 31
4.3.2.6.4 Short Control Signalling Transmissions . 34
4.3.2.7 Occupied Channel Bandwidth . 34
4.3.2.7.1 Applicability . 34
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 328 V2.1.1 (2016-11)
4.3.2.7.2 Definition. 35
4.3.2.7.3 Limits . 35
4.3.2.7.4 Conformance . 35
4.3.2.8 Transmitter unwanted emissions in the out-of-band domain . 35
4.3.2.8.1 Applicability . 35
4.3.2.8.2 Definition. 35
4.3.2.8.3 Limit . 35
4.3.2.8.4 Conformance . 35
4.3.2.9 Transmitter unwanted emissions in the spurious domain . 36
4.3.2.9.1 Applicability . 36
4.3.2.9.2 Definition. 36
4.3.2.9.3 Limit . 36
4.3.2.9.4 Conformance . 36
4.3.2.10 Receiver spurious emissions . 36
4.3.2.10.1 Applicability . 36
4.3.2.10.2 Definition. 36
4.3.2.10.3 Limit . 36
4.3.2.10.4 Conformance . 37
4.3.2.11 Receiver Blocking . 37
4.3.2.11.1 Applicability . 37
4.3.2.11.2 Definition. 37
4.3.2.11.3 Performance Criteria . 37
4.3.2.11.4 Limits . 37
4.3.2.11.5 Conformance . 38
4.3.2.12 Geo-location capability . 38
4.3.2.12.1 Applicability . 38
4.3.2.12.2 Definition. 38
4.3.2.12.3 Requirements . 39
5 Testing for compliance with technical requirements . 39
5.1 Environmental conditions for testing . 39
5.1.1 Introduction. 39
5.1.2 Normal test conditions . 39
5.1.2.1 Normal temperature and humidity . 39
5.1.2.2 Normal power source . 39
5.1.3 Extreme test conditions . 39
5.2 Interpretation of the measurement results . 39
5.3 Definition of other test conditions . 40
5.3.1 Test mode. 40
5.3.2 Antennas and transmit operating modes . 40
5.3.2.1 Integrated and dedicated antennas . 40
5.3.2.2 Smart antenna systems and related operating modes . 41
5.3.2.2.1 Introduction . 41
5.3.2.2.2 Operating mode 1 (single antenna) . 41
5.3.2.2.3 Operating mode 2 (multiple antennas, no beamforming) . 41
5.3.2.2.4 Operating mode 3 (multiple antennas, with beamforming) . 41
5.3.2.3 Configuration for testing . 41
5.3.3 Adaptive and Non-adaptive equipment. 41
5.3.4 Presentation of equipment . 41
5.3.4.1 Introduction . 41
5.3.4.2 Testing of stand-alone equipment . 41
5.3.4.3 Testing of host connected equipment and plug-in radio equipment . 42
5.3.4.3.1 Introduction . 42
5.3.4.3.2 The use of a host or test jig for testing plug-in radio equipment . 42
5.3.4.3.3 Testing of combinations . 42
5.3.5 Conducted measurements, radiated measurements, relative measurements . 43
5.4 Test procedures for essential radio test suites. 43
5.4.1 Product Information .
...
Final draft ETSI EN 300 328 V2.1.0 (2016-09)
HARMONISED EUROPEAN STANDARD
Wideband transmission systems;
Data transmission equipment operating
in the 2,4 GHz ISM band and
using wide band modulation techniques;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 328 V2.1.0 (2016-09)
Reference
REN/ERM-TG11-011
Keywords
broadband, data, harmonised standard, ISM,
LAN, mobile, radio, regulation, spread spectrum,
SRD, testing, transmission, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 328 V2.1.0 (2016-09)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 9
Introduction . 9
1 Scope . 10
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 15
4.1 Environmental profile . 15
4.2 Equipment types . 15
4.2.1 Modulation types . 15
4.2.2 Adaptive and non-adaptive equipment . 15
4.2.3 Receiver categories . 15
4.2.3.1 Introduction . 15
4.2.3.2 Categorization . 15
4.2.3.2.1 Receiver category 1 . 15
4.2.3.2.2 Receiver category 2 . 16
4.2.3.2.3 Receiver category 3 . 16
4.3 Conformance requirements . 16
4.3.1 Requirements for Frequency Hopping equipment . 16
4.3.1.1 Introduction . 16
4.3.1.2 RF output power . 16
4.3.1.2.1 Applicability . 16
4.3.1.2.2 Definition. 16
4.3.1.2.3 Limit . 16
4.3.1.2.4 Conformance . 16
4.3.1.3 Duty Cycle, Tx-sequence, Tx-gap . 16
4.3.1.3.1 Applicability . 16
4.3.1.3.2 Definition. 17
4.3.1.3.3 Limit . 17
4.3.1.3.4 Conformance . 17
4.3.1.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 17
4.3.1.4.1 Applicability . 17
4.3.1.4.2 Definition. 17
4.3.1.4.3 Limit . 17
4.3.1.4.4 Other Requirements . 18
4.3.1.4.5 Conformance . 18
4.3.1.5 Hopping Frequency Separation . 19
4.3.1.5.1 Applicability . 19
4.3.1.5.2 Definition. 19
4.3.1.5.3 Limit . 19
4.3.1.5.4 Conformance . 19
4.3.1.6 Medium Utilization (MU) factor . 19
4.3.1.6.1 Applicability . 19
4.3.1.6.2 Definition. 20
4.3.1.6.3 Limit . 20
4.3.1.6.4 Conformance . 20
4.3.1.7 Adaptivity (Adaptive Frequency Hopping) . 20
4.3.1.7.1 Applicability . 20
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 328 V2.1.0 (2016-09)
4.3.1.7.2 Adaptive Frequency Hopping using LBT based DAA . 20
4.3.1.7.3 Adaptive Frequency Hopping using other forms of DAA (non-LBT based) . 22
4.3.1.7.4 Short Control Signalling Transmissions . 23
4.3.1.8 Occupied Channel Bandwidth . 23
4.3.1.8.1 Applicability . 23
4.3.1.8.2 Definition. 24
4.3.1.8.3 Limits . 24
4.3.1.8.4 Conformance . 24
4.3.1.9 Transmitter unwanted emissions in the out-of-band domain . 24
4.3.1.9.1 Applicability . 24
4.3.1.9.2 Definition. 24
4.3.1.9.3 Limit . 24
4.3.1.9.4 Conformance . 24
4.3.1.10 Transmitter unwanted emissions in the spurious domain . 25
4.3.1.10.1 Applicability . 25
4.3.1.10.2 Definition. 25
4.3.1.10.3 Limit . 25
4.3.1.10.4 Conformance . 25
4.3.1.11 Receiver spurious emissions . 25
4.3.1.11.1 Applicability . 25
4.3.1.11.2 Definition. 25
4.3.1.11.3 Limit . 25
4.3.1.11.4 Conformance . 26
4.3.1.12 Receiver Blocking . 26
4.3.1.12.1 Applicability . 26
4.3.1.12.2 Definition. 26
4.3.1.12.3 Performance Criteria . 26
4.3.1.12.4 Limits . 26
4.3.1.12.5 Conformance . 27
4.3.1.13 Geo-location capability . 27
4.3.1.13.1 Applicability . 27
4.3.1.13.2 Definition. 27
4.3.1.13.3 Requirements . 28
4.3.2 Requirements for other types of Wide Band modulation . 28
4.3.2.1 Introduction . 28
4.3.2.2 RF output power . 28
4.3.2.2.1 Applicability . 28
4.3.2.2.2 Definition. 28
4.3.2.2.3 Limit . 28
4.3.2.2.4 Conformance . 28
4.3.2.3 Power Spectral Density . 28
4.3.2.3.1 Applicability . 28
4.3.2.3.2 Definition. 28
4.3.2.3.3 Limit . 29
4.3.2.3.4 Conformance . 29
4.3.2.4 Duty Cycle, Tx-sequence, Tx-gap . 29
4.3.2.4.1 Applicability . 29
4.3.2.4.2 Definition. 29
4.3.2.4.3 Limit . 29
4.3.2.4.4 Conformance . 29
4.3.2.5 Medium Utilization (MU) factor . 29
4.3.2.5.1 Applicability . 29
4.3.2.5.2 Definition. 29
4.3.2.5.3 Limit . 30
4.3.2.5.4 Conformance . 30
4.3.2.6 Adaptivity (adaptive equipment using modulations other than FHSS) . 30
4.3.2.6.1 Applicability . 30
4.3.2.6.2 Non-LBT based Detect and Avoid . 30
4.3.2.6.3 LBT based Detect and Avoid . 31
4.3.2.6.4 Short Control Signalling Transmissions . 34
4.3.2.7 Occupied Channel Bandwidth . 34
4.3.2.7.1 Applicability . 34
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 328 V2.1.0 (2016-09)
4.3.2.7.2 Definition. 35
4.3.2.7.3 Limits . 35
4.3.2.7.4 Conformance . 35
4.3.2.8 Transmitter unwanted emissions in the out-of-band domain . 35
4.3.2.8.1 Applicability . 35
4.3.2.8.2 Definition. 35
4.3.2.8.3 Limit . 35
4.3.2.8.4 Conformance . 35
4.3.2.9 Transmitter unwanted emissions in the spurious domain . 36
4.3.2.9.1 Applicability . 36
4.3.2.9.2 Definition. 36
4.3.2.9.3 Limit . 36
4.3.2.9.4 Conformance . 36
4.3.2.10 Receiver spurious emissions . 36
4.3.2.10.1 Applicability . 36
4.3.2.10.2 Definition. 36
4.3.2.10.3 Limit . 36
4.3.2.10.4 Conformance . 37
4.3.2.11 Receiver Blocking . 37
4.3.2.11.1 Applicability . 37
4.3.2.11.2 Definition. 37
4.3.2.11.3 Performance Criteria . 37
4.3.2.11.4 Limits . 37
4.3.2.11.5 Conformance . 38
4.3.2.12 Geo-location capability . 38
4.3.2.12.1 Applicability . 38
4.3.2.12.2 Definition. 38
4.3.2.12.3 Requirements . 39
5 Testing for compliance with technical requirements . 39
5.1 Environmental conditions for testing . 39
5.1.1 Introduction. 39
5.1.2 Normal test conditions . 39
5.1.2.1 Normal temperature and humidity . 39
5.1.2.2 Normal power source . 39
5.1.3 Extreme test conditions . 39
5.2 Interpretation of the measurement results . 39
5.3 Definition of other test conditions . 40
5.3.1 Test mode. 40
5.3.2 Antennas and transmit operating modes . 40
5.3.2.1 Integrated and dedicated antennas . 40
5.3.2.2 Smart antenna systems and related operating modes . 41
5.3.2.2.1 Introduction . 41
5.3.2.2.2 Operating mode 1 (single antenna) . 41
5.3.2.2.3 Operating mode 2 (multiple antennas, no beamforming) . 41
5.3.2.2.4 Operating mode 3 (multiple antennas, with beamforming) . 41
5.3.2.3 Configuration for testing . 41
5.3.3 Adaptive and Non-adaptive equipment. 41
5.3.4 Presentation of equipment . 41
5.3.4.1 Introduction . 41
5.3.4.2 Testing of stand-alone equipment . 41
5.3.4.3 Testing of host connected equipment and plug-in radio equipment . 42
5.3.4.3.1 Introduction . 42
5.3.4.3.2 The use of a host or test jig for testing plug-in radio equipment . 42
5.3.4.3.3 Testing of combinations . 42
5.3.5 Conducted measurements, radiated measurements, relative measurements. . 43
5.4 Test procedures for essential radio test suites.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.