SIST EN 4507:2014
(Main)Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water extractable matter
Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water extractable matter
This European Standard specifies the procedure for the determination of water extractable matter of textile material. This method has been written in response to an aerospace requirement for a method of extraction using hot water.
Luft- und Raumfahrt - Nichtmetallische Werkstoffe - Textilien - Prüfverfahren - Bestimmung von wasserlöslichen Stoffen
Série aérospatiale - Matériaux non-métalliques - Textiles - Méthode d'essai - Détermination des matières solubles dans l'eau
Aeronavtika - Nekovinski materiali - Tekstilije - Preskusne metode - Določanje vodotopnosti blaga
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Nichtmetallische Werkstoffe - Textilien - Prüfverfahren - Bestimmung von wasserlöslichen StoffenSérie aérospatiale - Matériaux non-métalliques - Textiles - Méthode d'essai - Détermination des matières solubles dans l'eauAerospace series - Non-metallic materials - Textiles - Test method - Determination of water extractable matter49.025.60TekstilijeTextilesICS:Ta slovenski standard je istoveten z:EN 4507:2013SIST EN 4507:2014en01-februar-2014SIST EN 4507:2014SLOVENSKI
STANDARD
SIST EN 4507:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4507
July 2013 ICS 49.025.60 English Version
Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water extractable matter
Série aérospatiale - Matériaux non-métalliques - Textiles - Méthode d'essai - Détermination des matières solubles dans l'eau
Luft- und Raumfahrt - Nichtmetallische Werkstoffe - Textilien - Prüfverfahren - Bestimmung von wasserlöslichen Stoffen This European Standard was approved by CEN on 8 May 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4507:2013: ESIST EN 4507:2014
EN 4507:2013 (E) 2 Contents Page Foreword . 3 Introduction . 4 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Health and safety . 4 5 Principle/Technique . 4 6 Resources/Facilities . 5 6.1 Apparatus . 5 6.2 Materials/Reagents . 5 6.3 Qualification of personnel . 5 7 Test samples/Test pieces . 5 8 Test procedure . 6 9 Expression of results . 6 9.1 Individual results . 6 9.2 Calculation. 6 10 Measurement uncertainties . 7 11 Designation . 7 12 Test report . 7
SIST EN 4507:2014
EN 4507:2013 (E) 3 Foreword This document (EN 4507:2013) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Janauary 2014, and conflicting national standards shall be withdrawn at the latest by January 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be hel
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.