SIST EN 61300-2-47:2016
(Main)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-47: Tests - Thermal shocks (IEC 61300-2-47:2016)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-47: Tests - Thermal shocks (IEC 61300-2-47:2016)
This part of IEC 61300 details a procedure for determining the suitability of a fibre optic
device to withstand the effects of thermal shock. In practice, this means a very short change
over time between extreme temperatures.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-47: Prüfungen - Temperaturschock
Dispositifs d'interconnexion et composants passifs fibroniques – Procédures fondamentales d'essais et de mesures - Partie 2-47: Essais - Chocs thermiques
L'IEC 61300-2-47:2016 détaille une procédure destinée à déterminer l'aptitude d'un dispositif fibronique à résister aux effets des chocs thermiques. En pratique, cela correspond à un temps de passage très court entre des températures extrêmes. Cette quatrième édition annule et remplace la troisième édition parue en 2010. Elle constitue une révision technique. La présente édition inclut la modification technique majeure suivante par rapport à l'édition précédente: révision de la limite de température de la sévérité d'essai.
Mots clés: chocs thermiques, températures extrêmes
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-47. del: Preskusi - Toplotni udar (IEC 61300-2-47:2016)
V tem delu standarda IEC 61300 je podrobno opisan postopek za ugotavljanje primernosti elementov z optičnimi vlakni za odpornost proti učinkom toplotnega šoka. V praksi to pomeni zelo kratek čas spremembe med ekstremnimi temperaturami.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-47: Tests - Thermal shocks (IEC 61300-2-47:2016)33.180.20Fibre optic interconnecting devicesICS:Ta slovenski standard je istoveten z:EN 61300-2-47:2016SIST EN 61300-2-47:2016en01-november-2016SIST EN 61300-2-47:2016SLOVENSKI
STANDARDSIST EN 61300-2-47:20111DGRPHãþD
SIST EN 61300-2-47:2016
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 61300-2-47
September 2016 ICS 33.180.20
Supersedes
EN 61300-2-47:2010
English Version
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-47: Tests - Thermal shocks (IEC 61300-2-47:2016)
Dispositifs d'interconnexion et composants passifs fibroniques - Procédures fondamentales d'essais et de mesures - Partie 2-47: Essais - Chocs thermiques (IEC 61300-2-47:2016)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-47: Prüfungen - Temperaturschock (IEC 61300-2-47:2016) This European Standard was approved by CENELEC on 2016-06-23. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61300-2-47:2016 E SIST EN 61300-2-47:2016
EN 61300-2-47:2016 2 European foreword The text of document 86B/3879/CDV, future edition 4 of IEC 61300-2-47, prepared by SC 86B "Fibre optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-47:2016. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-03-23 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2019-06-23
This document supersedes EN 61300-2-47:2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61300-2-47:2016 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: IEC 61753-1 NOTE Harmonized as EN 61753-1.
SIST EN 61300-2-47:2016
EN 61300-2-47:2016 3
Annex ZA (normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60068-2-14 -
Environmental testing -- Part 2-14: Tests - Test N: Change of temperature EN 60068-2-14 -
IEC 61300-3-1 -
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 3-1: Examinations and measurements - Visual examination EN 61300-3-1 -
SIST EN 61300-2-47:2016
SIST EN 61300-2-47:2016
IEC 61300-2-47 Edition 4.0 2016-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components – Basic test and measurement procedures –
Part 2-47: Tests – Thermal shocks
Dispositifs d'interconnexion et composants passifs fibroniques – Procédures fondamentales d'essais et de mesures –
Partie 2-47: Essais – Chocs thermiques
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 33.180.20
ISBN 978-2-8322-3418-1
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN 61300-2-47:2016
– 2 – IEC 61300-2-47:2016 © IEC 2016 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references. 5 3 General description . 5 4 Apparatus . 5 4.1 Testing chambers . 5 4.2 Support for mounting the DUT . 6 5 Procedure . 6 5.1 General . 6 5.2 Preconditioning . 6 5.3 Initial examination and measurement . 6 5.4 Testing . 6 5.5 Recovery . 7 5.6 Final examination and measurement . 7 6 Severity . 7 7 Details to be specified . 8 Annex A (informative)
Minimum temperature value in Finland . 9 Bibliography . 10
Figure 1 – Temperature change cycle . 7
SIST EN 61300-2-47:2016
IEC 61300-2-47:2016 © IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ___________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –
Part 2-47: Tests – Thermal shocks
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.