SIST EN 12312-14:2007+A1:2009
(Main)Aircraft ground support equipment - Specific requirements - Part 14: Disabled/incapacitated passenger boarding vehicles
Aircraft ground support equipment - Specific requirements - Part 14: Disabled/incapacitated passenger boarding vehicles
This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of disabled/incapacitated passenger boarding vehicles when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer or his authorised representative. It also takes into account some performance requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies.
This European Standard defines specific safety requirements for transporters/boarding vehicles for transporting/boarding incapacitated or disabled passengers as defined under 3.1, hereafter referred to as boarding vehicles.
This European Standard applies to pedestrian controlled self-propelled boarding vehicles, self-propelled boarding vehicles with integrated driver’s accommodation and towable boarding vehicles, used for moving disabled or incapacitated passengers at an airport between the terminal building and the aircraft ramp and to board and disembark those passengers to and from civil aircraft.
Examples of some typical boarding vehicles are shown in Annex A.
This European Standard assumes that a disabled or incapacitated passenger may be accompanied by an attendant and may be seated in a wheelchair or reclining on a stretcher trolley.
This European Standard also assumes that the types of wheelchairs which may be employed could be:
- Standard type wheelchairs, e.g. in accordance with EN 12183;
- Wheelchairs with or without occupant self-restraint system;
- Aircraft aisle-width wheelchairs;
- Non-standard wheelchairs used at airports;
- Non occupant propelled wheelchairs;
- Battery powered wheelchairs, e.g. in accordance with EN 12184.
NOTE It is assumed that battery powered wheelchairs would not be taken into the cabin of an aircraft.
Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil 14: Behinderten-Transportgeräte
Diese Europäische Norm legt die technischen Anforderungen zur Minimierung der in Abschnitt 4 aufgelisteten
Gefährdungen fest, die bei Inbetriebnahme, Betrieb und Wartung von Behinderten-Transportgeräten auftreten
können, wenn diese ihrer Bestimmung nach verwendet werden und wenn der Hersteller oder sein
Beauftragter einen möglichen Missbrauch voraussehen kann. Sie berücksichtigt auch einige Funktions- und
Gestaltungsanforderungen, die von offiziellen Stellen, Luftfahrzeug- und Bodengeräteherstellern sowie
Luftverkehrs- und Abfertigungsgesellschaften als wesentlich erachtet wurden.
Diese Europäische Norm legt spezielle Sicherheitsanforderungen für Fahrzeuge zur Beförderung von
behinderten Personen, wie sie unter 3.1 definiert werden, fest. Diese Fahrzeuge werden nachfolgend
Behinderten-Transportgeräte genannt.
Diese Europäische Norm gilt für mitgängergeführte Behinderten-Transportgeräte mit eigenem Antrieb,
Behinderten-Transportgeräte mit Fahrerplatz und eigenem Antrieb, schleppbare Behinderten-Transportgeräte,
die für den Transport von behinderten oder handlungsunfähigen Passagieren auf dem Flughafen zwischen
dem Flughafengebäude und dem Luftfahrzeug, auf dem Vorfeld sowie als Hilfseinrichtung an dem zivilen
Luftfahrzeug für behinderte oder handlungsunfähige Passagiere zum Ein- und Aussteigen verwendet werden.
Beispiele für einige typische Behinderten-Transportgeräte sind in Anhang A enthalten.
Diese Europäische Norm setzt voraus, dass behinderte oder handlungsunfähige Passagiere von einer Beaufsichtigungsperson
begleitet werden und in einem Rollstuhl sitzen oder auf einer fahrbaren Trage liegen
können.
Diese Europäische Norm setzt ferner voraus, dass der Einsatz folgender Rollstuhlausführungen möglich ist:
- nach Norm gebaute Rollstühle, z. B. nach EN 12183;
- Rollstühle mit oder ohne selbsttätigem Rückhaltesystem für Insassen;
- auf Gangbreite von Luftfahrzeugen angepasste Rollstühle;
Matériels au sol pour aéronefs - Exigences particulières - Partie 14: Matériel d'accès à bord des passagers handicapés
Podporna oprema na tleh za letalski promet - Posebne zahteve - 14. del: Prevozna sredstva za vkrcavanje trajno ali začasno funkcionalno oviranih potnikov
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RWQLNRYLuftfahrt-Bodengeräte - Besondere Anforderungen - Teil 14: Behinderten-TransportgeräteMatériels au sol pour aéronefs - Exigences particulières - Partie 14: Matériel d'accès à bord des passagers handicapésAircraft ground support equipment - Specific requirements - Part 14: Disabled/incapacitated passenger boarding vehicles49.100Oprema za servis in vzdrževanje na tlehGround service and maintenance equipmentICS:Ta slovenski standard je istoveten z:EN 12312-14:2006+A1:2009SIST EN 12312-14:2007+A1:2009en01-julij-2009SIST EN 12312-14:2007+A1:2009SLOVENSKI
STANDARD
SIST EN 12312-14:2007+A1:2009
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12312-14:2006+A1
April 2009 ICS 49.100 Supersedes EN 12312-14:2006English Version
Aircraft ground support equipment - Specific requirements - Part 14: Disabled/incapacitated passenger boarding vehicles
Matériels au sol pour aéronefs - Exigences particulières - Partie 14: Matériel d'accès à bord des passagers handicapés
Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil 14: Behinderten-Transportgeräte This European Standard was approved by CEN on 28 August 2006 and includes Amendment 1 approved by CEN on 1 March 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12312-14:2006+A1:2009: ESIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 2 Contents Page Foreword .3Introduction .41 Scope .52 Normative references .63 Terms and definitions .74 List of significant hazards .85 Safety requirements and/or measures .85.1 General requirements .85.2 Van body or main platform .95.3 Boarding platform . 105.4 Tail-lift . 115.5 Stability . 115.6 Speeds . 125.7 Controls . 125.8 Lights . 135.9 Options . 136 Information for use . 136.1 Marking . 136.2 Safety signs . 136.3 Warnings . 136.4 Instructions . 147 Verification of requirements . 14Annex A (informative)
Examples of typical boarding vehicles . 15Annex B (normative)
List of hazards in addition to those of EN 1915-1 . 18Annex C (informative)
Loading control . 20C.1 Machinery Directive requirements . 20C.2 Demonstration of absence of risk of overloading/overturning . 20Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC . 21Annex ZB (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 22Bibliography . 23 SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 3 Foreword This document (EN 12312-14:2006+A1:2009) has been prepared by Technical Committee CEN/TC 274 “Aircraft ground support equipment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2009-03-01. This document supersedes EN 12312-14:2006. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this document." This document is intended for use in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4. The Parts of EN 12312 — Aircraft ground support equipment — Specific requirements — are: Part 1: Passenger stairs Part 2: Catering vehicles Part 3: Conveyor belt vehicles Part 4: Passenger boarding bridges Part 5: Aircraft fuelling equipment Part 6: Deicers and deicing/antiicing equipment Part 7: Aircraft movement equipment Part 8: Maintenance stairs and platforms Part 9: Container/Pallet loaders Part 10: Container/Pallet transfer transporters Part 11: Container/Pallet dollies and loose load trailers Part 12: Potable water service equipment Part 13: Lavatory service equipment Part 14: Disabled/Incapacitated passenger boarding vehicles Part 15: Baggage and equipment tractors Part 16: Air start equipment Part 17: Air conditioning equipment Part 18: Nitrogen or Oxygen units Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions Part 20: Electrical ground power units According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 4 Introduction This European Standard defines health and safety requirements, as well as some functional and performance requirements for transport and boarding vehicles intended for moving disabled or incapacitated passengers on an airfield between the terminal building and the aircraft. Major factors in the design of the equipment, with relevance to safety, are the consideration of psychological aspects, i.e. feelings of well-being and security, and the physical comfort of the passenger and the avoidance of panic. The minimum essential criteria are considered to be of primary importance in providing safe, serviceable, economical and usable disabled/incapacitated passenger boarding vehicles. Deviations from the recommended criteria should occur only after careful consideration, extensive testing and thorough in-service evaluation have shown alternative methods or conditions to be satisfactory. This European Standard is a Type C standard as stated in !EN ISO 12100". The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 5
1 Scope This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of disabled/incapacitated passenger boarding vehicles when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer or his authorised representative. It also takes into account some performance requirements recognized as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This European Standard defines specific safety requirements for transporters/boarding vehicles for transporting/boarding incapacitated or disabled passengers as defined under 3.1, hereafter referred to as boarding vehicles. This European Standard applies to pedestrian controlled self-propelled boarding vehicles, self-propelled boarding vehicles with integrated driver’s accommodation and towable boarding vehicles, used for moving disabled or incapacitated passengers at an airport between the terminal building and the aircraft ramp and to board and disembark those passengers to and from civil aircraft. Examples of some typical boarding vehicles are shown in Annex A. This European Standard assumes that a disabled or incapacitated passenger may be accompanied by an attendant and may be seated in a wheelchair or reclining on a stretcher trolley. This European Standard also assumes that the types of wheelchairs which may be employed could be: Standard type wheelchairs, e.g. in accordance with EN 12183; Wheelchairs with or without occupant self-restraint system; Aircraft aisle-width wheelchairs; Non-standard wheelchairs used at airports; Non occupant propelled wheelchairs; Battery powered wheelchairs, e.g. in accordance with EN 12184. NOTE It is assumed that battery powered wheelchairs would not be taken into the cabin of an aircraft. This European Standard does not apply to other forms of aircraft loaders not specifically designed for boarding of incapacitated or disabled passengers, e.g. mobile lounges, boarding bridges or externally mounted pods such as used on helicopters. Noise and vibration are dealt with respectively in EN 1915-4 and EN 1915-3. This European Standard does not deal with hazards in respect to a standard automotive chassis and from other vehicles on the apron. This Part of EN 12312 is not applicable to disabled/incapacitated passenger boarding vehicles which are manufactured before the date of publication by CEN of this standard.
!This part of EN 12312 is intended to be used in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 (for vehicles) and EN 1915-4." SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 6 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. !deleted text" EN 1050:1996, Safety of machinery — Principles for risk assessment EN 1175-1, Safety of industrial trucks - Electrical requirements - Part 1: General requirements for battery powered trucks EN 1756-2, Tail lifts — Platform lifts for mounting on wheeled vehicles — Safety requirements — Part 2: Tail lifts for passengers EN 1837, Safety of machinery — Integral lighting of machines EN 1915-1:2001, Aircraft ground support equipment - General requirements — Part 1: Basic safety requirements EN 1915-2, Aircraft ground support equipment - General requirements — Part 2: Stability and strength requirements, calculations and test methods EN 1915-3, Aircraft ground support equipment — General requirements — Part 3: Vibration measurement methods and reduction EN 1915-4, Aircraft ground support equipment — General requirements — Part 4: Noise measurement methods and reduction EN 12183, Manual wheelchairs — Requirements and test methods EN 12184, Electrically powered wheelchairs, scooters and their chargers — Requirements and test methods EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) !EN ISO 12100-2:2003, Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles (ISO 12100-2:2003)" !EN ISO 13850:2008, Safety of machinery - Emergency stop - Principles for design (ISO 13850:2006)"
EN ISO 14122-3:2001, Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001) ISO 7193, Wheelchairs — Maximum overall dimensions ISO 7718, Aircraft — Main-deck passenger doors — Interface requirements for connection with passenger-boarding bridge or transfer vehicle ISO 10542-1, Technical systems and aids for disabled or handicapped persons — Wheelchair tiedown and occupant-restraint systems — Part 1: Requirements and test methods for all systems ISO 10542-2, Technical systems and aids for disabled or handicapped persons — Wheelchair tiedown and occupant-restraint systems — Part 2: Four-point strap-type tiedown systems ISO 10542-3, Technical systems and aids for disabled or handicapped persons — Wheelchair tiedown and occupant-restraint systems — Part 3: Docking-type tiedown systems ISO 16004, Aircraft ground equipment — Passenger boarding bridge or transfer vehicle — Requirements for interface with aircraft doors SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 7 3 Terms and definitions For the purposes of this document, the terms and definitions given in !EN ISO 12100:2003" and EN 1915-1:2001 and the following apply. 3.1 disabled passenger person with one or more impairments, one or more disabilities, one or more handicaps or a combination of impairment, disability and/or handicap which restricts their mobility 3.2 incapacitated passenger person whose mobility is temporarily impaired 3.3 wheelchair wheeled chair, either occupant-propelled, pushed or power operated (which may be capable of being folded or dismantled) and fitted with or without an occupant restraint system 3.4 stretcher trolley wheeled trolley with integral or removable stretcher (which may be capable of being folded or dismantled) attendant operated, non self-propelled 3.5 attendant person who assists a disabled/incapacitated person NOTE Examples of the ways in which attendants assist disabled persons are e.g. pushing wheelchairs, operating hoists, assisting with entering and leaving seats, beds and wheelchairs. 3.6 restraint device device for preventing movement of a person or load 3.7 boarding platform platform for transhipment between van body and aircraft 3.8 van body enclosed body for carrying loads, e.g. disabled/incapacitated persons, wheelchairs, stretcher trolleys 3.9 main platform open lifting platform for carrying loads, e.g. disabled/incapacitated persons, wheelchairs, stretcher trolleys 3.10 tail-lift (tailgate lift) moveable platform at the rear of a vehicle used for assisting the entry or exit of passengers, with or without wheelchairs or stretcher trolleys, into and out of vehicles to a height of not more than 1 700 mm 3.11 under-run guard rigid or flexible bumper device which is designed to prevent another vehicle from becoming entrapped underneath the rear of a vehicle when the vehicle is struck from behind 3.12 sideguard rigid device which is designed to prevent another vehicle from becoming entrapped underneath the side of a vehicle when the vehicle is struck from either side SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 8 4 List of significant hazards The list of risks and hazards (see Annex B) is based on EN 1050 and contains all the specific hazards, hazardous situations and events additional to those of the EN 1915 series, as far as they are dealt with in this European Standard, identified by risk assessment as significant for disabled/incapacitated passenger boarding vehicles and which require action to eliminate or reduce risks. 5 Safety requirements and/or measures 5.1 General requirements 5.1.1 !!!!Disabled/Incapacitated passenger boarding equipment shall conform to the relevant requirements of EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4 unless otherwise specified in this standard." They shall also conform to the specific requirements of this European Standard. NOTE The design of electrical equipment should take into account any potential interference with passengers fitted with pacemakers or accompanying electrical equipment. Consideration should be given to the requirements of EN 60601-1 in relation to any medical equipment that may be used on the boarding vehicle. 5.1.2 Strength calculations shall be carried out in accordance with EN 1915-2. 5.1.3 The overall dimensions of the boarding vehicle shall be kept to a minimum, consistent with this function in handling the loads. The overall width of the boarding vehicle in the driving condition (with stabilizers retracted) should not exceed 2 600 mm. In the fully lowered position, the vehicle should not exceed a height of 4,0 m. NOTE A practical upper limit of 3 800 mm has been found to suit the majority of major airport local height restrictions. 5.1.4 The electrical system of battery powered boarding vehicles shall conform to EN 1175-1 with the exception of standard automotive chassis. 5.1.5 Self-propelled boarding vehicles with a driver's cabin shall have an alternative means of exit for the driver in the event of an emergency. It shall be positioned as far as possible away from the normal exit. 5.1.6 Restraint systems shall be fitted to all seats on self-propelled boarding vehicles a lap type seat belt as a minimum. 5.1.7 Where a driver’s cabin is installed, it shall not obstruct the transfer of passengers to and from the aircraft. NOTE The driver’s cabin may be located at either side. 5.1.8 The driver's cabin shall not project beyond the leading edge of the boarding platform, see also 5.3.7. 5.1.9 It shall be possible to smooth the transfer of a wheelchair or stretcher trolley from the boarding vehicle to the aircraft, e.g. by providing an integral or manually attached bridging section. Variations in height in between the sections shall not exceed 5 mm. 5.1.10 The ground clearance of the boarding vehicle shall allow without interference the transversing of two surfaces intersecting at an angle of 3° (5 %) either in bridging or in cresting. 5.1.11 Structural parts or stabilizers of pedestrian controlled self-propelled boarding vehicles shall not protrude from the overall length within the operating range of the tiller. 5.1.12 Vibration measurement and protection shall be carried out in accordance with EN 1915-3. 5.1.13 Noise measurement and protection shall be carried out in accordance with EN 1915-4. SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 9 5.1.14 The vehicle chassis at ground level shall be surrounded by a protective structure in order to prevent any possibility of inadvertent access of persons under the van body while elevated (see 5.14 and Annex D of EN 1915-1:2001). 5.1.15 The van body or main platform shall be equipped with a means for safe access of staff from ground level. 5.1.16 Where under-run guards or sideguards are creating crushing or shearing hazards, measures shall be taken to avoid these hazards (see 5.14 and Annex D of EN 1915-1:2001). NOTE Under-run guards and/or sideguards can be required, by law, in the country of use for vehicles to be used on public roadways. 5.1.17 In deviation from 5.17.5 of EN 1915-1:2001, hydraulic fluid tanks shall be dimensioned so that during maximum system displacement at least 20 % of the fluid volume remains in the tank. 5.2 Van body or main platform 5.2.1 Cylinders in hydraulic lifting systems shall be protected against unintentional lowering by e.g. a pilot-operated check-valve mounted directly to the cylinder (see 5.20.3 of EN 1915-1:2001). 5.2.2 It shall be sufficient to carry the passengers on wheelchairs or stretchers plus attendants and any ancillary equipment as intended. The local load capacity of the van body or main platform shall not be less than 3 000 N/m2 evenly distributed. 5.2.3 The floor of the van body or main platform shall be covered with a hard wearing anti-slip surface in accordance with EN 1915-1:2001, 5.12.1. 5.2.4 Devices to restrain wheel chairs stretcher trolleys and occupants shall be provided. The design of restraint devices and anchorage points shall be capable of withstanding the imposed loads under driving conditions up to the maximum driving speed of the boarding vehicle. Restraint systems shall be designed according to ISO 10542-1, ISO 10542-2 or ISO 10542-3. 5.2.5 The interior dimensions of the main platform shall be such that wheelchair(s) or stretcher trolley(s), plus attendant(s) and equipment, can be accommodated safely. Details of the maximum dimensions for wheelchairs are given in EN 12183, EN 12184 and ISO 7193. NOTE For design purposes, stretcher trolleys can be taken as having a minimum overall length of 1 900 mm, overall width of 570 mm and maximum raised height of 940 mm. Taking anthropometric changes into account, a minimum overall length of 2 100 mm is recommended. 5.2.6 The internal height of the van body shall not be less than 1 900 mm. NOTE Preferably, a minimum height of 2 100 mm should be used wherever possible. 5.2.7 Seats with restraint systems shall be provided for the intended number of attendants accompanying disabled/incapacitated passengers according to the load capacity of the boarding vehicle. 5.2.8 Open main platforms shall be equipped with fixed railings or side panels on both sides. NOTE Preferably, full panels should be used. 5.2.9 Doors or railings with moveable parts in accordance with EN 1915-1:2001, 5.12.2, shall be provided at each end of the van body or main platform. Minimum dimensions of openings shall be in accordance with 5.2.5. Gaps between adjoining handrails shall be in accordance with EN ISO 14122-3:2001, 7.1.9. SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 10 5.2.10 It shall not be possible to inadvertently open any door/railing with the van body or main platform in the raised position. 5.2.11 Means shall be provided to gain access to the van body or main platform in the lowered position, e.g. lowering capability of the lifting system to ground level, installation of a tail-lift. 5.2.12 The variation in heights between the sections shall not exceed 5 mm, the breadth of gaps between different areas shall be less than 10 mm. Where the difference of height is more than 5 mm, the change-over edge shall be realized with an inclination at a maximum angle of 15°. 5.2.13 The inner surfaces of the van body or main platform shall include no projections or corners that could cause injuries, e.g. corners shall be chamfered or rounded to a minimum radius of 3 mm unless smooth corners are provided by the intrinsic design of the standard material profiles used in the construction. 5.2.14 The interior of an enclosed van body shall be compatible with repeated cleaning using strong detergents and disinfecting agents, as well as suitable for repeated water pressure and steam cleaning. 5.2.15 Fully enclosed van bodies shall have windows along each longitudinal side. The windows shall be arranged so that passengers on seats, wheelchairs and stretchers are able to look through. 5.2.16 Fully enclosed van bodies shall be ventilated.
The ventilation shall be capable of providing fresh air at the minimum rate of 43 m3/h. NOTE The need for a heating or air conditioning system should be agreed between manufacturer and user (see Clause 0 of EN 1915-1:2001 — negotiation). 5.3 Boarding platform 5.3.1 The local load capacity of the boarding platforms shall not be less than 3 000 N/m2 evenly distributed. The floor deflection shall not exceed 6 mm, to enable a safe transhipment between van body/main platform and aircraft. NOTE Boarding platforms may be an integrated part of the van body or main platform. 5.3.2 The floor surface of the boarding platform shall: a) be anti-slip in accordance with EN 1915-1:2001, 5.12.1; b) provide the possibility of elimination of water and snow, e.g. drainage. 5.3.3 The minimum usable width of the boarding platform shall be 500 mm. 5.3.4 Where the boarding platform is narrower than the full width of the vehicle, the platform shall allow for lateral movement to align with the aircraft door. Minimum lateral adjustment shall be 200 mm. 5.3.5 The boarding platform shall extend a minimum of 500 mm beyond the extreme front face of the van body/main platform when it is in fully retracted position. 5.3.6 On self-propelled boarding platforms the boarding platform shall be constructed so that the driver at the operating position is able to see the leading edge throughout its operating range. 5.3.7 Handrails against falling shall be provided on all open sides of the boarding platform except for access to the aircraft and van body or main platform. NOTE 1 Preferably, full panels should be used. NOTE 2 Gaps between adjoining handrails should be in accordance with EN ISO 14122-3:2001, 7.1.9. NOTE 3 For the purposes of this clause, it should be considered the aircraft's fuselage, located at no more than 150 mm from the edge of the boarding platform, ensures safeguarding. 5.3.8 The front end of guardrails adjacent to the aircraft shall be equipped with a suitable bumper. SIST EN 12312-14:2007+A1:2009
EN 12312-14:2006+A1:2009 (E) 11 5.3.9 The boarding platform and guardrails adjacent to the aircraft shall have a capability to provide an adaptation to the contour of the aircraft. Platforms and railings shall be of such design to leave a maximum gap of 150 mm to the aircraft fuselage. The profile shall conform to the interface requirements given in ISO 7718 and ISO 16004. 5.3.10 Narrow boarding platforms, not allowing unobstructed opening and closing of aircraft doors to be serviced as intended by the manufacturer, shall be equipped with sliding guardrails. NOTE Some aircraft types have recessed doors that produce an overall door swing of 1,7 m. 5.3.11 The maximum extending force applied to the aircraft of the boarding vehicle by telescopic parts of the boarding platform and guardrails shall not exceed 400 N. Where the maximum force caused by movement of the aircraft exceeds 400 N, these telescopic parts shall give way to avoid damage to the aircraft. 5.3.12 Where a canopy over the boarding platform is fitted for weather protection, it shall have a profile in accordance with the requirements of ISO 7718 a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.