SIST EN 61300-1:2004
(Main)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 1: General and guidance
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 1: General and guidance
Contains a series of environmental test and measurement procedures and, in some cases, preferred severities designed to assess the ability of fibre optic interconnecting devices and passive components to perform under expected service conditions. The object is to provide uniform and reproducible environmental test procedures and measurement procedures, for those preparing specifications for fibre optic interconnecting devices and passive components.Information is provided on the following propities of components and equipment, such as connectors, splices, switches, attenuators, etc.: a) ability to operate within specified limits of temperature, pressure, humidity, mechanical stress, or other environmental conditions and certian combinations of these conditions; b) ability to withstand storage and transport; c) ability to meet the specified levels of optical performance.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren -- Teil 1: Allgemeines und Leitfaden
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales d'essais et de mesures -- Partie 1: Généralités et guide
En anglais seulement.
Povezovalne naprave in pasivne komponente optičnih vlaken – Postopki osnovnega preskušanja in merjenja – 1. del: Splošno in smernice (IEC 61300-1:2003)*
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 61300-1:2004
STANDARD
september 2004
Povezovalne naprave in pasivne komponente optičnih vlaken – Postopki
osnovnega preskušanja in merjenja – 1. del: Splošno in smernice (IEC 61300-
1:2003)*
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 1: General and guidance (IEC 61300-1:2003)
ICS 33.180.20 Referenčna številka
SIST EN 61300-1:2004(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 61300-1
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2003
ICS 33.180.20 Supersedes EN 61300-1:1997
English version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures
Part 1: General and guidance
(IEC 61300-1:2003)
Dispositifs d'interconnexion et Lichtwellenleiter-Verbindungselemente
composants passifs à fibres optiques - und passive Bauteile -
Méthodes fondamentales d'essais Grundlegende Prüf- und Messverfahren
et de mesures Teil 1: Allgemeines und Leitfaden
Partie 1: Généralités et guide (IEC 61300-1:2003)
(CEI 61300-1:2003)
This European Standard was approved by CENELEC on 2003-11-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-1:2003 E
---------------------- Page: 2 ----------------------
EN 61300-1:2003 - 2 -
Foreword
The text of document 86B/1849/FDIS, future edition 2 of IEC 61300-1, prepared by SC 86B, Fibre optic
interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-1 on 2003-11-01.
This European Standard supersedes EN 61300-1:1997.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-11-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annexes A, B and ZA are normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61300-1:2003 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 3 ----------------------
- 3 - EN 61300-1:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1)
IEC 60050-731 - International Electrotechnical Vocabulary - -
(IEV)
Chapter 731: Optical fibre communication
1) 2)
IEC 60068-2-1 - Environmental testing EN 60068-2-1 1993
Part 2: Tests - Tests A: Cold
1)
IEC 60617 - Graphical symbols for diagrams - -
database
1) 2)
IEC 60825-1 - Safety of laser products EN 60825-1 1994
Part 1: Equipment classification, + corr. February 1995
requirements and user's guide
1) 2)
IEC 60825-2 - Part 2: Safety of optical fibre EN 60825-2 2000
communication systems
1) 2)
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 1997
passive components - Basic test and
measurement procedures
Part 3-1: Examinations and
measurements - Visual examination
1) 2)
IEC 61315 - Calibration of fibre optic power meters EN 61315 1997
1) 2)
ISO 4288 - Geometrical Product Specifications EN ISO 4288 1997
(GPS) - Surface texture: Profile method -
Rules and procedures for the
assessment of surface texture
1)
Undated reference.
2)
Valid edition at date of issue.
---------------------- Page: 4 ----------------------
NORME CEI
INTERNATIONALE IEC
61300-1
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2003-06
Dispositifs d'interconnexion et
composants passifs à fibres optiques –
Procédures fondamentales d'essais
et de mesures –
Partie 1:
Généralités et guide
Fibre optic interconnecting devices
and passive components –
Basic test and measurement procedures –
Part 1:
General and guidance
© IEC 2004 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
PRICE CODE Q
Commission Electrotechnique Internationale
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 5 ----------------------
61300-1 © IEC:2004 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9
1 Scope.11
2 Normative references.13
3 Terms and definitions .13
4 Standard atmospheric conditions.15
5 Significance of the numerical value of a quantity .15
6 Graphical symbols and terminology .19
7 Safety.19
8 Calibration.19
9 Launch conditions.21
Annex A (normative) Round robin calibration procedure for dimensional measurements
on ferrules and sleeves.23
Annex B (normative) Launch conditions .29
Bibliography.35
---------------------- Page: 6 ----------------------
61300-1 © IEC:2004 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –
Part 1: General and guidance
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61300-1 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition published in 1995. It constitutes a
technical revision.
This bilingual version (2004-07) replaces the English version.
The text of this standard is based on the following documents:
FDIS Report on voting
86B/1849/FDIS 86B/1877/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
---------------------- Page: 7 ----------------------
61300-1 © IEC:2004 – 7 –
The French version of this standard has not been voted upon.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
IEC 61300 consists of the following parts, under the general title: Fibre optic interconnecting
devices and passive components – Basic test and measurement procedures:
− Part 1: General and guidance
− Part 2: Tests
− Part 3: Examinations and measurements
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the
data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 8 ----------------------
61300-1 © IEC:2004 – 9 –
INTRODUCTION
The publications of the IEC 61300 series contain fundamental information on environmental
testing procedures and measurement procedures relating to fibre optic interconnecting
devices and passive components. They are intended to be used to achieve uniformity and
reproducibility in environmental testing procedures and measurement procedures.
The term "test procedure" refers to procedures commonly known as environmental tests. The
expressions "environmental conditioning" and "environmental testing" refer to the
environments to which components or equipment may be exposed so that an assessment may
be made of their performance under the conditions of use, transport and storage.
The term "measurement procedure" refers to those measurements which are necessary
to assess the physical and optical characteristics of a component and may also be used
before, during or after a test procedure to measure the effects of environmental conditioning or
testing. The return loss and attenuation tests are examples of measurement procedures.
The requirements for the performance of components or equipment subjected to the test and
measurement procedures described in this standard are not included. The relevant
specification for the device under test defines the allowed performance limits.
When drafting a specification or purchase contract, only those tests should be specified which
are necessary for the relevant components or equipment taking into account the technical and
economic aspects.
The environmental test procedures are contained in the IEC 61300-2 series and the
measurement procedures in the IEC 61300-3 series. Each test or measurement procedure is
published as a stand-alone publication so that it may be modified, expanded or cancelled
without having an effect on any other test or measurement procedure. However, it should be
noted that, where practical, reference is made to other standards as opposed to repeating all
or part of already existing standards. As an example, the cold test for fibre optic apparatus
refers to IEC 60068-2-1, but it also provides other needed information such as purpose,
recommended severities and a list of items to be specified.
Multiple methods may be contained in a test or measurement procedure. As an example,
several methods of measuring attenuation are contained in the attenuation measurement
procedure.
If more than one method is contained in a test or measurement procedure, the reference
method is identified.
---------------------- Page: 9 ----------------------
61300-1 © IEC:2004 – 11 –
FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –
Part 1: General and guidance
1 Scope
This part of IEC 61300 contains a series of environmental test and measurement procedures
and, in some cases, preferred severities designed to assess the ability of fibre optic
interconnecting devices and passive components to perform under expected service
conditions. Although the severities are primarily intended for land-based communications, the
procedures may be used for other applications.
The object of this standard is to provide uniform and reproducible environmental test
procedures and measurement procedures, for those preparing specifications for fibre optic
interconnecting devices and passive components.
These test and measurement procedures are based on available international engineering
experience and judgement, and are designed to provide information on the following properties
of components and equipment, such as connectors, splices, switches, attenuators, etc.:
a) ability to operate within specified limits of temperature, pressure, humidity, mechanical
stress or other environmental conditions and certain combinations of these conditions;
b) ability to withstand storage and transport;
c) ability to meet the specified levels of optical performance.
The tests in this standard permit the performance of sample components or equipment to be
compared. To assess the overall quality of a production lot, the test procedures should be
applied in accordance with a suitable sampling plan and may be supplemented by appropriate
additional tests, if necessary.
To provide tests appropriate to the different intensities of an environmental condition, some of
the test procedures have a number of degrees of severity. These different degrees of severity
are obtained by varying the time, temperature or some other determining factor separately or
in combination.
This standard should be used in combination with the relevant specification which will define
the tests to be used, the required degree of severity for each of them, their sequence,
if relevant, and the permissible performance limits. In the event of conflict between this basic
standard and the relevant specification, the latter will take precedence.
---------------------- Page: 10 ----------------------
61300-1 © IEC:2004 – 13 –
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60050-731, International Electrotechnical Vocabulary – Chapter 731: Optical fibre
communication
IEC 60068-2-1 Environmental testing – Part 2: Tests – Tests A: Cold
1
IEC 60617 [DB-2002] , Graphical symbols for diagrams
IEC 60825-1, Safety of laser products – Part 1: Equipment classification, requirements and
user's guide
IEC 60825-2, Safety of laser products – Part 2: Safety of optical fibre communication
systems
IEC 61300-3-1, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-1:Examinations and measurements – Visual examination
IEC 61315, Calibration of fibre optic power meters
ISO 4288, Geometrical Product Specifications (GPS) – Surface texture: Profile method –
Rules and procedures for the assessment of surface texture
3 Terms and definitions
For the purposes of this part of IEC 61300, the following terms and definitions apply.
3.1
test
complete series of steps designed to subject specimens to an environmental condition or
series of conditions and which normally consists of the following:
a) pre-conditioning (where required);
b) initial examination and measurements (where required);
c) conditioning;
d) re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.