iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 61300-2-8:1999

(Main)

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-8: Tests - Bump

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-8: Tests - Bump

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Meßverfahren -- Teil 2-8: Prüfungen - Vielfachschock

Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes fondamentales d'essais et de mesures -- Partie 2-8: Essais - Secousses

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-8: Tests – Bump (IEC 61300-2-8:1995)

General Information

Status
Published
Publication Date
30-Apr-1999
ICS
33.180.20 - Fibre optic interconnecting devices
Technical Committee
iTEL - Communication cables
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-May-1999
Due Date
01-May-1999
Completion Date
01-May-1999
Ref Project
EN 61300-2-8:1997 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-8: Tests - Bump

Buy Standard

EN 61300-2-8:1999EN 61300-2-8:1999
PreviousNext
Standard
EN 61300-2-8:1999
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61300-2-8:1999
01-maj-1999
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-8: Tests – Bump (IEC 61300-2-8:1995)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures -- Part 2-8: Tests - Bump
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Meßverfahren -- Teil 2-8: Prüfungen - Vielfachschock
Dispositifs
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 61300-3-29:2014(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-29: Examinations and measurements - Spectral transfer characteristics of DWDM devices
EN 61300-3-29:2014

EN IEC 61300-3-29 identifies two basic measurement methods for characterizing the spectral transfer functions of DWDM devices. The transfer functions are the functions of transmittance dependent of wavelengths. In this standard, optical attenuations are also used. The transfer functions can be used to produce measurements of insertion loss (IL), polarization dependent loss (PDL), isolation, centre wavelength, bandwidth (BW) and other optical performances.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61300-2-42:2014(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief
EN 61300-2-42:2014

EN IEC 61300-2-42 specifies a test to determine the influence of a side load applied to a cord assembled with a strain relief. The intention is to simulate a static load, due to a length of fibre cable, which would typically be experienced during service. Components should withstand side loads during optical transmission without degradation of the optical performance. Besides a boot, any feature that controls the bending radius of the fibre can be considered as strain relief.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61753-057-2:2013(Main)
Fibre optic interconnecting devices and passive components - Performance standard - Part 057-2: Single mode fibre plug-recptacle-receptacle style optical fuse for category C - Controlled environment (IEC 61753-057-2:2012)
EN 61753-057-2:2013

This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which a fibre optical fuse satisfies in order to be categorised as meeting the requirements of single mode fibre plug-receptacle style optical fuse used in controlled environments. Optical performance specified in this document relate to plug-receptacle style configuration fuses only.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61753-143-2:2013(Main)
Fibre optic interconnecting devices and passive components - Performance standard - Part 143-2: Optical passive VIPA-based dispersion compensator of single-mode fibre transmission for category C - Controlled environments (IEC 61753-143-2:2012)
EN 61753-143-2:2013

This part of IEC 61753 contains the minimum test and measurement requirements and severity levels that a passive chromatic dispersion compensator (PCDC) using virtually imaged phased array (VIPA) must satisfy in order to be categorized as meeting the IEC standard, category C-controlled environments. Generally, PCDCs are used to reduce the magnitude of chromatic dispersion (CD) between regenerators by adding CD to the span that has a sign opposite to the total CD of the fibre cable and components. The requirements cover non-connectorized PCDCs used in single-channel transmission and wavelength division multiplexing (WDM) transmission in single-mode fibres(IEC 60793-2-50 B1/B2/B4).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61300-2-19:2013(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state) (IEC 61300-2-19:2012)
EN 61300-2-19:2013

This part of IEC 61300 details a procedure for determining the suitability of a fibre optic device to withstand the environmental condition of high humidity and high temperature which may occur in actual use, storage and/or transport. The test is primarily intended to permit the observation of effects of high humidity at constant temperature over a given period. Absorption of moisture may result in swelling that would destroy functional utility, cause loss of physical strength, and cause changes in other important mechanical properties. Degradation of optical properties may also occur. Although not necessarily intended as a simulated tropical test, this test can, nevertheless, be useful in determining moisture absorption of insulating or covering materials.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61753-056-2:2013(Main)
Fibre optic interconnecting devices and passive components - Performance standard - Part 056-2: Single mode fibre pigtailed style optical fuse for category C - Controlled environment (IEC 61753-056-2:2012)
EN 61753-056-2:2013

This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which a fibre optical fuse satisfies in order for it to be categorised as meeting the requirements of single mode fibre pigtailed style optical fuse used in controlled environments. Optical performance specified in this document relates to in-line type configurations fuses only.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61300-2-11:2013(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-11: Tests - Axial compression (IEC 61300-2-11:2012)
EN 61300-2-11:2013

The purpose of this part of IEC 61300 is to ensure that the captivation ort he attachment of the cable to the fibre optic device will withstand compressive axial loads likely to be applied during normal service.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50516-1-1:2012/AC:2013(Corrigendum)
Industrial connector sets and interconnect components to be used in optical fibre control and communication systems - Product specifications -- Part 1-1: Type SC-RJ PC industrial terminated on EN 60793-2-10 category A1a and A1b multimode fibre to meet the requirements of category I (industrial environments) as specified in IEC/PAS 61753-1-3
EN 50516-1-1:2011/AC:2012

This European Standard contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements that an SC-RJ connector set with one side protected by an industrial housing with the fibres terminated with cylindrical zirconia PC ferrules, an adaptor fitted with resilient alignment sleeves and
patchcord shall meet in order for it to be categorised as an EN standard product. The product is rated IP67. Since different variants are permitted, product marking details are given in 3.6.

  • Corrigendum
    2 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61754-26:2012(Main)
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 26: Type SF connector famlily (IEC 61754-26:2012)
EN 61754-26:2012

This part of IEC 61754 defines the standard interface dimensions for the type SF optical board connector that uses a normal glass fibre and the physical contact technique to connect flexible optical boards and ribbon fibres.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61300-2-33:2012(Main)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-33: Tests - Assembly and disassembly of fibre optic mechanical splices, fibre management systems and closures (IEC 61300-2-33:2012)
EN 61300-2-33:2012

This part of the IEC 61300 series, evaluates the assembly and reassembly of a fibre optic mechanical splice, a fibre management system or a closure for a specified number of times. The test procedures simulate the following conditions which may be encountered during the component's service lifetime: - the ability of an optical mechanical splice to be re-installed after disassembly; - the ability to re-enter fibre management systems and closures, by accessing fibres and optical components and making reconfigurations without disturbing transmission in adjacent fibre circuits; - verification of the sealing performance after frequent opening and closing of enclosures.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day