SIST EN 61300-2-19:2013

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state) (IEC 61300-2-19:2012)

This part of IEC 61300 details a procedure for determining the suitability of a fibre optic device to withstand the environmental condition of high humidity and high temperature which may occur in actual use, storage and/or transport. The test is primarily intended to permit the observation of effects of high humidity at constant temperature over a given period. Absorption of moisture may result in swelling that would destroy functional utility, cause loss of physical strength, and cause changes in other important mechanical properties. Degradation of optical properties may also occur. Although not necessarily intended as a simulated tropical test, this test can, nevertheless, be useful in determining moisture absorption of insulating or covering materials.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-19: Prüfungen - Feuchte Wärme (konstant) (IEC 61300-2-19:2012)

Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes fondamentales d'essais et de mesures - Partie 2-19: Essais - Chaleur humide (essai continu) (CEI 61300-2-19:2012)

La CEI 61300-2-19:2012 détermine l'aptitude d'un dispositif à fibres optiques à supporter un environnement très humide et à température élevée, qui peut se produire en cours d'utilisation réelle, de stockage et/ou de transport. L'essai sert avant tout à permettre l'observation des effets d'une humidité élevée à température constante pendant une période donnée. Cette troisième édition annule et remplace la deuxième édition publiée en 2005. Elle constitue une révision technique. Les modifications par rapport à l'édition antérieure ont pour but de reconsidérer les sévérités et les détails à spécifier. Mots clés: humide et à température élevée, supporter un environnement

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-19. del: Preskusi - Pregreta para (ustaljeno stanje) (IEC 61300-2-19:2012)

V tem delu standarda IEC 61300 je podrobno opisan postopek za ugotavljanje primernosti optičnih spojnih elementov in pasivnih komponent za odpornost proti okoljskemu pogoju visoke vlažnosti in temperature, ki se lahko pojavi med dejanskim delovanjem, shranjevanjem in/ali transportom. Preskus je prvenstveno namenjen omogočanju opazovanja učinkov visoke vlage pri stalni temperaturi v določenem časovnem območju. Zaradi absorpcije vlage se lahko pojavi nabrekanje, ki lahko uniči funkcionalnost ter povzroči izgubo fizične moči in spremembe drugih pomembnih mehanskih lastnosti. Tudi optične lastnosti se lahko poslabšajo. Ta preskus je lahko koristen tudi pri ugotavljanju absorpcije vlage pri izolacijskih in pokrivnih materialih, čeprav prvenstveno ni bil mišljen kot simuliran tropski preskus.

General Information

• Status: Published
• Publication Date: 04-Mar-2013
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: iTEL - Communication cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 20-Feb-2013
• Due Date: 27-Apr-2013
• Completion Date: 05-Mar-2013
• Ref Project: EN 61300-2-19:2013 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state)

Relations

• Corrected By: SIST EN 61300-2-19:2013/AC:2020 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state) (IEC 61300-2-19:2012/COR1:2020)
• Effective Date: 31-Mar-2020
• Revised: SIST EN 61300-2-19:2006 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-19: Tests - Damp heat (steady state)
• Effective Date: 17-Dec-2013
• Replaces: SIST EN 61300-2-19:2006 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-19: Tests - Damp heat (steady state)
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61300-2-19:2013
01-april-2013
1DGRPHãþD
SIST EN 61300-2-19:2006
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHVNXVL3UHJUHWDSDUDXVWDOMHQRVWDQMH,(&

Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-19: Tests - Damp heat (steady state) (IEC 61300-2-
19:2012)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-19: Prüfungen - Feuchte Wärme (konstant) (IEC 61300-2-
19:2012)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d'essais et de mesures - Partie 2-19: Essais - Chaleur humide (essai
continu) (CEI 61300-2-19:2012)
Ta slovenski standard je istoveten z: EN 61300-2-19:2013
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61300-2-19:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61300-2-19:2013

---------------------- Page: 2 ----------------------

SIST EN 61300-2-19:2013

EUROPEAN STANDARD
EN 61300-2-19

NORME EUROPÉENNE
February 2013
EUROPÄISCHE NORM

ICS 33.180.20 Supersedes EN 61300-2-19:2005


English version


Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-19: Tests -
Damp heat (steady state)
(IEC 61300-2-19:2012)


Dispositifs d'interconnexion et composants Lichtwellenleiter -
passifs à fibres optiques - Verbindungselemente und passive
Méthodes fondamentales d'essais et de Bauteile -
mesures - Grundlegende Prüf- und Messverfahren -
Partie 2-19: Essais - Teil 2-19: Prüfungen -
Chaleur humide (essai continu) Feuchte Wärme (konstant)
(CEI 61300-2-19:2012) (IEC 61300-2-19:2012)





This European Standard was approved by CENELEC on 2012-12-12. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-2-19:2013 E

---------------------- Page: 3 ----------------------

SIST EN 61300-2-19:2013
EN 61300-2-19:2013 - 2 -

Foreword
The text of document 86B/3491/FDIS, future edition 3 of IEC 61300-2-19, prepared by SC 86B, "Fibre
optic interconnecting devices and passive components", of IEC TC 86, "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-19:2013.
The following dates are fixed:
(dop) 2013-09-12
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2013-12-12
standards conflicting with the

document have to be withdrawn

This document supersedes EN 61300-2-19:2005.
The changes with respect to EN 61300-2-19:2005 are to reconsider the severities and details to be
specified.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61300-2-19:2012 was approved by CENELEC as a
European Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 61300-2-19:2013
- 3 - EN 61300-2-19:2013
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60068-2-78 - Environmental testing - EN 60068-2-78 -
Part 2-78: Tests - Test Cab: Damp heat,
steady state


IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements -
Visual examination


IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -
Part 3-3: Examinations and measurements -
Active monitoring of changes in attenuation
and return loss


IEC 61300-3-4 - Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures -
Part 3-4: Examinations and measurements -
Attenuation

---------------------- Page: 5 ----------------------

SIST EN 61300-2-19:2013

---------------------- Page: 6 ----------------------

SIST EN 61300-2-19:2013



IEC 61300-2-19

®


Edition 3.0 2012-11




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Fibre optic interconnecting devices and passive components – Basic test

and measurement procedures –

Part 2-19: Tests – Damp heat (steady state)




Dispositifs d'interconnexion et composants passifs à fibres optiques –

Méthodes fondamentales d’essais et de mesures –


Partie 2-19: Essais – Chaleur humide (état continu)













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX J


ICS 33.180.20 ISBN 978-2-83220-469-6



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61300-2-19:2013
– 2 – 61300-2-19 © IEC:2012
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 General description . 5
4 Apparatus . 5
4.1 Chamber . 5
4.2 Steam . 6
4.3 Optical measurements . 6
4.4 Positioning and mounting of the specimen . 6
5 Procedure. 7
5.1 General . 7
5.2 Preconditioning . 7
5.3 Initial examinations and measurements . 7
5.4 Conditioning . 7
5.5 Recovery . 8
5.6 Final examinations and measurements . 8
6 Severity . 8
7 Details to be specified . 8

Table 1 – Severities . 8

---------------------- Page: 8 ----------------------

SIST EN 61300-2-19:2013
61300-2-19 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-19: Tests – Damp heat (steady state)


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any
...