SIST EN 61300-2-42:2014

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief

EN IEC 61300-2-42 specifies a test to determine the influence of a side load applied to a cord assembled with a strain relief. The intention is to simulate a static load, due to a length of fibre cable, which would typically be experienced during service. Components should withstand side loads during optical transmission without degradation of the optical performance. Besides a boot, any feature that controls the bending radius of the fibre can be considered as strain relief.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-42: Prüfungen - Statische Seitenlast für die Zugentlastung

Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales d'essais et de mesures - Partie 2-42: Essais - Charge latérale statique pour serre-câble

IEC 61300-2-42:2014 spécifie un essai destiné à déterminer l'influence d'une charge latérale appliquée à un cordon assemblé comportant un serre-câble. L'intention est de simuler une charge statique exercée par une longueur de câble à fibres, que l'on rencontre généralement au cours d'utilisation. Il convient que les composants résistent aux charges latérales pendant toute transmission optique, sans dégradation des performances optiques. Outre un embout, tout dispositif permettant de contrôler le rayon de courbure de la fibre peut être considéré comme un serre-câble. Cette troisième édition annule et remplace la deuxième édition parue en 2005, et constitue une révision technique. La présente troisième édition contient les modifications techniques significatives suivantes par rapport à l'édition précédente: la modification de la  sévérité selon les configurations du câble.   Mots clés: charge latérale, charge statique, serre-câble

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-42. del: Preskusi - Statična bočna obremenitev za razbremenilno sponko (IEC 61300-2-42:2014)

Standard EN IEC 61300-2-42 določa preskus za ugotavljanje vpliva bočne obremenitve sestavljenega kabla za razbremenilno sponko. Namenjen je simulaciji statične obremenitve zaradi dolžine optičnega kabla, ki so ji kabli običajno izpostavljeni v času uporabe. Sestavni deli naj bi zdržali bočno obremenitev med optičnim prenosom, ne da bi se pri tem poslabšala optična zmogljivost. Poleg čevljev se katera koli lastnost, ki nadzoruje polmer upogibanja vlakna, lahko šteje za razbremenilno sponko.

General Information

• Status: Published
• Publication Date: 13-Jul-2014
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: iTEL - Communication cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 16-Jun-2014
• Due Date: 21-Aug-2014
• Completion Date: 14-Jul-2014
• Ref Project: EN 61300-2-42:2014 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief

Relations

• Replaces: SIST EN 61300-2-42:2006 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-42: Tests - Static side load for connectors
• Effective Date: 29-Jan-2023
• Revised: SIST EN 61300-2-42:2006 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-42: Tests - Static side load for connectors
• Effective Date: 06-May-2014
• Replaces: SIST EN 61300-2-42:2006 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-42: Tests - Static side load for connectors
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61300-2-42:2014
01-september-2014
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHVNXVL6WDWLþQDERþQDREUHPHQLWHY]DUD]EUHPHQLOQR
VSRQNR,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-42: Tests - Static side load for strain relief
Ta slovenski standard je istoveten z: EN 61300-2-42:2014
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61300-2-42:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61300-2-42:2014

---------------------- Page: 2 ----------------------

SIST EN 61300-2-42:2014


EUROPEAN STANDARD EN 61300-2-42

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2014
ICS 33.180.20 Supersedes EN 61300-2-42:2005
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-42: Tests -
Static side load for strain relief
(IEC 61300-2-42:2014)
Dispositifs d'interconnexion et composants passifs à fibres Lichtwellenleiter - Verbindungselemente und passive
optiques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren –
mesures - Partie 2-42: Essais - Charge latérale statique Teil 2-42: Prüfungen - Statische Seitenlast für die
pour serre-câble Zugentlastung
(CEI 61300-2-42:2014) (IEC 61300-2-42:2014)
This European Standard was approved by CENELEC on 2014-03-13. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61300-2-42:2014 E

---------------------- Page: 3 ----------------------

SIST EN 61300-2-42:2014
EN 61300-2-42:2014 - 2 -
Foreword
The text of document 86B/3699/FDIS, future edition 3 of IEC 61300-2-42, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-42:2014.
The following dates are fixed:
– latest date by which the document has to be implemented at (dop) 2014-12-13
national level by publication of an identical national
standard or by endorsement
– latest date by which the national standards conflicting with (dow) 2015-03-13
the document have to be withdrawn

This document supersedes EN 61300-2-42:2005.
EN 61300-2-42:2014 includes the following significant technical changes with respect to
EN 61300-2-42:2005:
– modification of the severity according to cable configurations.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61300-2-42:2014 was approved by CENELEC as a
European Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 61300-2-42:2014
- 3 - EN 61300-2-42:2014
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 61300-1 -  Fibre optic interconnecting devices and passive EN 61300-1 -
components - Basic test and measurement
procedures
Part 1: General and guidance
IEC 61300-3-1 -  Fibre optic interconnecting devices and passive EN 61300-3-1 -
components - Basic test and measurement
procedures
Part 3-1: Examinations and measurements -
Visual examination
IEC 61300-3-3 -  Fibre optic interconnecting devices and passive EN 61300-3-3 -
components - Basic test and measurement
procedures
Part 3-3: Examinations and measurements -
Active monitoring of changes in attenuation and
return loss
IEC 61300-3-4 -  Fibre optic interconnecting devices and passive EN 61300-3-4 -
components - Basic test and measurement
procedures
Part 3-4: Examinations and measurements -
Attenuation

---------------------- Page: 5 ----------------------

SIST EN 61300-2-42:2014

---------------------- Page: 6 ----------------------

SIST EN 61300-2-42:2014



IEC 61300-2-42

®


Edition 3.0 2014-02




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –

Part 2-42: Tests – Static side load for strain relief




Dispositifs d’interconnexion et composants passifs à fibres optiques –

Procédures fondamentales d'essais et de mesures –


Partie 2-42: Essais – Charge latérale statique pour serre-câble













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX J


ICS 33.180.20 ISBN 978-2-8322-1378-0



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61300-2-42:2014
– 2 – 61300-2-42 © IEC:2014
CONTENTS

FOREWORD . 3
1 Scope . 5
2 Normative references. 5
3 General description . 5
4 Apparatus . 5
4.1 Load generator . 5
4.2 Holding fixture . 6
4.3 Optical source and detector . 6
5 Procedure . 6
5.1 Preparation of specimens . 6
5.2 Pre-conditioning . 6
5.3 Initial measurements . 6
5.4 Conditioning . 6
5.5 Measure the attenuation . 7
5.6 Apply cable load . 7
5.7 Monitor attenuation . 7
5.8 Recovery . 7
5.9 Final measurements and examinations . 8
5.10 Repeated testing . 8
6 Severity . 8
7 Details to be specified . 9

Figure 1 – Test apparatus for static side load . 7

Table 1 – Severities . 8

---------------------- Page: 8 ----------------------

SIST EN 61300-2-42:2014
61300-2-42 © IEC:2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
__________

FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-42: Tests – Static side load for strain relief


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC
...