SIST EN 60384-20:2002
(Main)Fixed capacitors for use in electronic equipment -- Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors
Fixed capacitors for use in electronic equipment -- Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors
with editorial correction
Festkondensatoren zur Verwendung in Geräten der Elektronik -- Teil 20: Rahmenspezifikation: Oberflächenmontierbare Festkondensatoren mit metallisierter Polyphenyl-Sulfid-Folie als Dielektrikum für Gleichspannung
Condensateurs fixes utilisés dans les équipements électroniques -- Partie 20: Spécification intermédiaire: Condensateurs fixes pour montage en surface pour courant continu à diélectrique en film de sulfure de polyphénylène métallisé
Fixed capacitors for use in electronic equipment - Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors (IEC 60384-20:1996)
General Information
Relations
This May Also Interest You
This part of IEC 60384 is applicable to fixed surface mount capacitors for direct current, with
metallized electrodes and polyethylene naphthalate dielectric for use in electronic equipment.
These capacitors have metallized connecting pads or soldering strips and are intended to be
mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors
can have "self-healing properties" depending on conditions of use. They are primarily intended
for applications where the AC component is small with respect to the rated voltage.
This part of IEC 60384 specifies preferred ratings and characteristics, selects from
IEC 60384‑1:2021 the appropriate quality assessment procedures, tests and measuring
methods and gives general performance requirements for this type of capacitor. Test severities
and requirements specified in detail specifications referring to this sectional specification are
of an equal or higher performance level. Lower performance levels are not permitted.
Capacitors for electromagnetic interference suppression are not included, but are covered by
IEC 60384‑14.
- Standard40 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft36 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 60384-20:2023 is available as which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60384-20:2023 is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyphenylene sulfide dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors can have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the AC component is small with respect to the rated voltage. This part of IEC 60384 specifies preferred ratings and characteristics and selects from IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level; lower performance levels are not permitted. Capacitors for electromagnetic interference suppression are not included but are covered by IEC 60384‑14. This edition includes the following significant technical changes with respect to the previous edition:
- revision of all parts of the document based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents;
- the document structure has been organized to follow new sectional specification structure decided in TC 40;
- revised tables and Clause 5 so as to prevent duplications and contradictions;
- in Clause 5.2 (Mounting), the Subclauses 5.2.1, 5.2.2 and 5.2.3 have been added;
- in Subclause 5.5 (Shear test), the Subclauses 5.5.1 and 5.5.2 have been added;
- in Subclause 5.14 (Component solvent resistance), the Subclauses 5.14.1 and 5.14.2 have been added. In Table 8 and Table A.2, test 5.14 has been moved before 5.7.5 (Final inspections and requirements) in Group 1A and in Subgroup C1;
- in Subclause 5.15 (Solvent resistance of marking), the Subclauses 5.15.1 and 5.15.2 have been added;
- tangent of loss angle measurement has been added to resistance to soldering heat test;
- lot-by-lot and periodical inspection tables, including requirements, have been moved to Annex A;
- revised Inspection Level (IL) of A1 subgroup.
- Standard39 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft37 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 60384-14:2023 applies to capacitors and resistor-capacitor combinations intended to be connected to AC mains or other supply with a nominal voltage not exceeding 1 000 V AC (RMS), and with a nominal frequency not exceeding 100 Hz. This document includes also additional specific conditions and requirements for the connection to DC supplies with a rated voltage not exceeding 1 500 V DC. The principal object of this part of IEC 60384 is to prescribe preferred ratings and characteristics and to select, from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification are of equal or higher performance level; lower performance levels are not permitted. This document also provides a schedule of safety tests to be used by national testing stations in countries where approval by such stations is required. The overvoltage categories in combination with the AC mains voltages for the capacitors classified in this document are to be taken from IEC 60664-1. This edition includes the following significant technical changes with respect to the previous edition:
- in damp heat steady state test, all capacitor types are tested both with and without rated voltage; the number of test pieces has been increased ;
- tangent of loss angle is added In Group 0 tests, in safety tests
- qualification approval based on safety and performance tests has been removed from the main text to a normative annex;
- the range of rated voltages is given instead of exact rated voltage values;
- normative annex for description of capacitor styles and of creepage/clearance distance measurement has been added;
- the importance of mechanical failures (cracks) in component encapsulation as a safety feature is highlighted in handling instructions and requirements after all relevant tests.
- Standard91 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft90 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 62391 applies to fixed electric double-layer capacitors (hereafter referred to as
capacitors) mainly used in DC circuits of electric and electronic equipment.
This part of IEC 62391 establishes standard terms, inspection procedures and methods of test
for use in sectional and detail specifications of electronic components for quality assessment
or any other purpose.
- Standard65 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft61 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 60384-1 establishes a generic template and specifies requirements to the
content of detail specifications for capacitors within the IEC 60384-X series.
- Standard24 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft19 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 60384 is applicable to fixed surface mount capacitors for direct current, with
metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment.
These capacitors have metallized connecting pads or soldering strips and are intended to be
mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors
can have "self-healing properties" depending on conditions of use. They are primarily intended
for applications where the AC component is small with respect to the rated voltage.
This part of IEC 60384 specifies preferred ratings and characteristics, and selects from
IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring
methods, and gives general performance requirements for this type of capacitor. Test severities
and requirements specified in detail specifications referring to this sectional specification are
of an equal or higher performance level. Lower performance levels are not permitted.
Capacitors for electromagnetic interference suppression are not included, but are covered by
IEC 60384-14.
- Standard40 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 60384 is a generic specification and is applicable to fixed capacitors for use in electronic equipment.
It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.
- Standard84 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 60384 applies to fixed capacitors for direct current, with metallized electrodes
and polyethylene-terephthalate dielectric for use in electronic equipment.
These capacitors have a possibility of "self-healing properties" depending on conditions of use.
They are primarily intended for applications where the AC component is small with respect to
the rated voltage. Two performance grades of capacitors are covered: grade 1 for long-life
application and grade 2 for general application.
Capacitors for electromagnetic interference suppression and surface mount fixed metallized
polyethylene-terephthalate film dielectric DC capacitors are not included, but are covered by
IEC 60384-14 and IEC 60384-19, respectively.
The object of this document is to prescribe preferred ratings and characteristics and to select
from IEC 60384-1 the appropriate quality assessment procedures, tests and measuring
methods, and to give general performance requirements for this type of capacitor. Test
severities and requirements prescribed in detail specifications referring to this sectional
specification are of equal or higher performance level, because lower performance levels are
not permitted.
- Standard35 pagesEnglish languagesale 10% offe-Library read for×1 day
2021-01-15 - IEC Corrected Version.
- Corrigendum5 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 60384 specifies preferred ratings and characteristics, selects from
IEC 60384-1:2016 the appropriate quality assessment procedures, tests and measuring
methods, and gives general performance requirements for this type of capacitor. Test
severities and requirements specified in detail specifications referring to this sectional
specification are of an equal or higher performance level. Lower performance levels are not
permitted.
This part of IEC 60384 applies to fixed direct current capacitors, using as dielectric a
polypropylene film with electrodes of thin metal foils. The capacitors covered by this
document are intended for use in electronic equipment.
Capacitors for electromagnetic interference suppression are not included, but are covered by
IEC 60384-14.
- Standard36 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.