Connectors for electronic equipment - Part 7-51: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz (IEC 60603-7-51:2010)

This part of IEC 60603 covers 8-way, shielded, free and fixed connectors, references dimensional, mechanical, electrical and environmental characteristics and tests in IEC 60603-7, and specifies electrical transmission requirements, including power sum alien (exogenous) crosstalk, for frequencies up to 500 MHz. These connectors are typically used as category 6A connectors in class EA cabling systems specified in ISO/IEC 11801. These connectors are intermateable and interoperable with other IEC 60603-7 series connectors as defined in Clause 2 of IEC 60603-7-1. These connectors are backward compatible with other IEC 60603-7 series connectors.

Steckverbinder für elektronische Einrichtungen - Teil 7-51: Bauartspezifikation für geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 500 MHz (IEC 60603-7-51:2010)

Connecteurs pour équipements électroniques - Partie 7-51: Spécification particulière pour les fiches et les embases blindées à 8 voies pour la transmission de données à des fréquences jusqu'à 500 MHz (CEI 60603-7-51:2010)

La CEI 60603-7-51:2010 couvre les fiches et les embases blindées à 8 voies et spécifie les exigences dimensionnelles, mécaniques, électriques et environnementales ainsi que les essais dans la CEI 60603-7 et elle spécifie les exigences de transmission électrique y compris la puissance de diaphonie exogène cumulée pour des fréquences jusqu'à 500 MHz. Ces connecteurs sont accouplables et interopérables avec les autres connecteurs de la série CEI 60603-7 comme cela est défini à l'Article 2 de la CEI 60603-7-1. Ces connecteurs offrent une compatibilité amont avec les autres connecteurs de la série CEI 60603-7.

Konektorji za elektronsko opremo - 7-51. del: Podrobna specifikacija za 8-polne, zaslonjene, proste in pritrjene konektorje za prenos podatkov s frekvencami do 500 MHz (IEC 60603-7-51:2010)

Ta del IEC 60603 zajema 8-polne, zaslonjene, proste in fiskne konektorje in se sklicuje na dimenzijske, mehanske, električne in okoljske značilnosti in preskuse v IEC 60603-7, ter določa zahteve za prevajanje električnega toka za frekvence do 500 MHz. Ti konektorji se običajno uporabljajo kot kategorija 6A konektorjev iz razreda EA kabelskih sistemov, določenih v ISO/IEC 11801. Ti konektorji so medsebojno združljivi in interoperabilni z drugimi konektorji serije IEC 60603-7, kot je opredeljeno v Klavzuli 2 IEC 60603-7. Ti konektorji so povratno skladni z drugimi konektorji serije IEC 60603-7.

General Information

Status
Published
Publication Date
21-Jul-2010
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
07-Jul-2010
Due Date
11-Sep-2010
Completion Date
22-Jul-2010

Buy Standard

Standard
SIST EN 60603-7-51:2010
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 60603-7-51:2010
01-september-2010
Konektorji za elektronsko opremo - 7-51. del: Podrobna specifikacija za 8-polne,
zaslonjene, proste in pritrjene konektorje za prenos podatkov s frekvencami do
500 MHz (IEC 60603-7-51:2010)

Connectors for electronic equipment - Part 7-51: Detail specification for 8-way, shielded,

free and fixed connectors, for data transmissions with frequencies up to 500 MHz (IEC

60603-7-51:2010)

Steckverbinder für elektronische Einrichtungen - Teil 7-51: Bauartspezifikation für

geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 500 MHz

(IEC 60603-7-51:2010)

Connecteurs pour équipements électroniques - Partie 7-51: Spécification particulière

pour les fiches et les embases blindées à 8 voies pour la transmission de données à des

fréquences jusqu'à 500 MHz (CEI 60603-7-51:2010)
Ta slovenski standard je istoveten z: EN 60603-7-51:2010
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60603-7-51:2010 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60603-7-51:2010
---------------------- Page: 2 ----------------------
SIST EN 60603-7-51:2010
EUROPEAN STANDARD
EN 60603-7-51
NORME EUROPÉENNE
May 2010
EUROPÄISCHE NORM
ICS 31.220.10
English version
Connectors for electronic equipment -
Part 7-51: Detail specification for 8-way, shielded, free and fixed
connectors, for data transmissions with frequencies up to 500 MHz
(IEC 60603-7-51:2010)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen – Teil 7-51:

Partie 7-51: Spécification particulière Bauartspezifikation für geschirmte freie

pour les fiches et les embases blindées und feste Steckverbinder, 8polig,
à 8 voies pour la transmission de données für Datenübertragungen bis 500 MHz
à des fréquences jusqu'à 500 MHz (IEC 60603-7-51:2010)
(CEI 60603-7-51:2010)

This European Standard was approved by CENELEC on 2010-05-01. CENELEC members are bound to comply

with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on

application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CENELEC member into its own language and notified

to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,

the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60603-7-51:2010 E
---------------------- Page: 3 ----------------------
SIST EN 60603-7-51:2010
EN 60603-7-51:2010 - 2 -
Foreword

The text of document 48B/2093/FDIS, future edition 1 of IEC 60603-7-51, prepared by SC 48B,

Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic

equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as

EN 60603-7-51 on 2010-05-01.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent

rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-05-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice

The text of the International Standard IEC 60303-7-51:2010 was approved by CENELEC as a European

Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60512-2-1 NOTE Harmonized as EN 60512-2-1.
IEC 60512-26-100:2008 NOTE Harmonized as EN 60512-26-100:2008 (not modified).
__________
---------------------- Page: 4 ----------------------
SIST EN 60603-7-51:2010
- 3 - EN 60603-7-51:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.

NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD

applies.
Publication Year Title EN/HD Year
IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 -
and measurements -
Part 1-100: General - Applicable publications
IEC 60512-25-9 - Connectors for electronic equipment - Tests EN 60512-25-9 -
and measurements -
Part 25-9: Signal integrity tests - Test 25i:
Alien crosstalk
IEC 60512-27-100 - Connectors for electronic equipment - Tests - -
and measurements -
Part 27-100: Signal integrity tests up to
500 MHz on IEC 60603-7 series connectors -
Tests 27a to 27g
IEC 60603-7 2008 Connectors for electronic equipment - EN 60603-7 2009
Part 7: Detail specification for 8-way,
unshielded, free and fixed connectors
IEC 60603-7-1 2009 Connectors for electronic equipment - EN 60603-7-1 2009
Part 7-1: Detail specification for 8-way,
shielded, free and fixed connectors
IEC 61156 Series Multicore and symmetrical pair/quad cables - -
for digital communications
---------------------- Page: 5 ----------------------
SIST EN 60603-7-51:2010
---------------------- Page: 6 ----------------------
SIST EN 60603-7-51:2010
IEC 60603-7-51
Edition 1.0 2010-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment –
Part 7-51: Detail specification for 8-way, shielded, free and fixed connectors,
for data transmissions with frequencies up to 500 MHz
Connecteurs pour équipements électroniques –
Partie 7-51: Spécification particulière pour les fiches et les embases blindées
à 8 voies pour la transmission de données à des fréquences jusqu'à 500 MHz
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX
ICS 31.220.10 ISBN 2-8318-1080-7
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60603-7-51:2010
– 2 – 60603-7-51 © IEC:2010
CONTENTS

FOREWORD...........................................................................................................................4

INTRODUCTION.....................................................................................................................6

1 General ............................................................................................................................7

1.1 Scope......................................................................................................................7

1.2 Normative references ..............................................................................................7

2 Terms and definitions .......................................................................................................8

3 Common features and isometric view ...............................................................................8

4 Cable terminations and internal connections – Fixed and free connectors ........................8

5 Gauges ............................................................................................................................8

6 Characteristics .................................................................................................................8

6.1 General ...................................................................................................................8

6.2 Pin and pair grouping assignment. ..........................................................................8

6.3 Classification into climatic category.........................................................................8

6.4 Electrical characteristics..........................................................................................8

6.5 Transmission characteristics ...................................................................................8

6.5.1 General .......................................................................................................8

6.5.2 Insertion loss...............................................................................................9

6.5.3 Return loss ..................................................................................................9

6.5.4 Propagation delay .......................................................................................9

6.5.5 Delay skew..................................................................................................9

6.5.6 NEXT loss ...................................................................................................9

6.5.7 Power sum NEXT loss (for information only)................................................9

6.5.8 FEXT Loss.................................................................................................10

6.5.9 Power sum FEXT loss (for information only) ..............................................10

6.5.10 Transverse conversion loss .......................................................................10

6.5.11 Transverse conversion transfer loss ..........................................................10

6.5.12 Power Sum Alien (Exogenous) NEXT ........................................................10

6.5.13 Power Sum Alien (Exogenous) FEXT.........................................................11

6.6 Mechanical............................................................................................................11

7 Tests and test schedule..................................................................................................11

7.1 General .................................................................................................................11

7.2 Arrangement for contact resistance test ................................................................11

7.3 Arrangement for vibration test ...............................................................................11

7.4 Test procedures and measuring methods ..............................................................11

7.5 Preconditioning .....................................................................................................11

7.6 Wiring and mounting of specimens ........................................................................12

7.6.1 Wiring........................................................................................................12

7.6.2 Mounting ...................................................................................................12

7.7 Test schedules ......................................................................................................12

7.7.1 Basic (minimum) test schedule ..................................................................12

7.7.2 Full test schedule ......................................................................................12

Bibliography..........................................................................................................................14

---------------------- Page: 8 ----------------------
SIST EN 60603-7-51:2010
60603-7-51 © IEC:2010 – 3 –

Table 1 – Test Group EP ......................................................................................................13

---------------------- Page: 9 ----------------------
SIST EN 60603-7-51:2010
– 4 – 60603-7-51 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
Part 7-51: Detail specification for 8-way, shielded, free and fixed
connectors, for data transmissions with frequencies up to 500 MHz
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance u
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.