oSIST prEN IEC 60794-1-127:2025
(Main)Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Indoor simulated installation test, method e27
Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Indoor simulated installation test, method e27
Câbles à fibres optiques - Partie1-127: Spécification générique - Procédures fondamentales d’essais des câbles optiques - Méthodes d’essais mécaniques - Essai d'installation simulée en intérieur, méthode e27
Optični kabli - 1-127. del: Splošna specifikacija - Osnovni preskusni postopki za optične kable - Mehanske preskusne metode - Preskus simulirane namestitve v notranjih prostorih, metoda e27
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2025
Optični kabli - 1-127. del: Splošna specifikacija - Osnovni preskusni postopki za
optične kable - Mehanske preskusne metode - Preskus simulirane namestitve v
notranjih prostorih, metoda e27
Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test
procedures - Mechanical tests methods - Indoor simulated installation test, method e27
Câbles à fibres optiques - Partie1-127: Spécification générique - Procédures
fondamentales d’essais des câbles optiques - Méthodes d’essais mécaniques - Essai
d'installation simulée en intérieur, méthode e27
Ta slovenski standard je istoveten z: prEN IEC 60794-1-127:2025
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
86A/2538/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60794-1-127 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2025-02-21 2025-05-16
SUPERSEDES DOCUMENTS:
86A/2459/CD, 86A/2535/CC
IEC SC 86A : FIBRES AND CABLES
SECRETARIAT: SECRETARY:
France Mr Laurent Gasca
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures -
Mechanical tests methods - Indoor simulated installation test, Method E27
PROPOSED STABILITY DATE: 2028
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
IEC CDV 60794-1-127 ED1 © IEC 2025 2 86A/2538/CDV
1 CONTENTS
2 CONTENTS . 2
3 FOREWORD . 3
4 INTRODUCTION . 5
5 1 Scope . 6
6 2 Normative references . 6
7 3 Terms and definitions . 6
8 4 Method E27: Indoor simulated installation test . 6
9 4.1 Object . 6
10 4.2 Sample . 7
11 4.3 Apparatus . 7
12 4.4 Procedure . 8
13 4.5 Requirements . 9
14 4.6 Details to be specified . 9
15 4.7 Details to be reported . 9
17 Figure 1 – Indoor installation simulation apparatus. 7
18 Figure 2 – Stapling and bending test fixture . 7
IEC CDV 60794-1-127 ED1 © IEC 2025 3 86A/2538/CDV
21 INTERNATIONAL ELECTROTECHNICAL COMMISSION
22 ____________
24 OPTICAL FIBRE CABLES –
26 Part 1-127: Generic specification –
27 Basic optical cable test procedures –
28 Mechanical tests methods - Indoor simulated installation test, method E27
30 FOREWORD
31 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
32 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
33 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
34 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
35 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
36 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
37 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
38 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
39 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
40 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
41 consensus of opinion on the relevant subjects since each technical committee has representation from all
42 interested IEC National Committees.
43 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
44 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
45 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
46 misinterpretation by any end user.
47 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
48 transparently to the maximum extent possible in their national and regional publications. Any divergence between
49 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
50 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
51 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
52 services carried out by independent certification bodies.
53 6) All users should ensure that they have the latest edition of this publication.
54 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
55 members of its technical committees and IEC National Committees for any personal injury, property damage or
56 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
57 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
58 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
59 indispensable for the correct application of this publication.
60 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
61 rights. IEC shall not be held responsible for identifying any or all such patent rights.
62 International Standard IEC 60794-1-21 has been prepared by subcommittee 86A: Fibres and cables, of IEC
63 technical committee 86: Fibre optics.
64 IEC 60794-1-127 has been prepared by subcommittee 86A: Fibres and cables, of IEC
65 technical committee 86: Fibre optics. It is an International Standard.
67 This first edition cancels and replaces Method E27 of the first edition of IEC 60794-1-21:2015,
68 which will be withdrawn. It constitutes a technical revision.
69 This edition includes the following significant technical changes with respect to the previous
70 edition:
71 a) added a new clause “4.7 Details to be reported”;
72 The text of this is based on the following documents:
Draft Report on voting
XX/XX/FDIS XX/XX/RVD
IEC CDV 60794-1-127 ED1 © IEC 2025 4 86A/2538/CDV
74 Full information on the voting for its approval can be found in the report on voting indicated in
75 the above table.
76 The language used for the development of this International Standard is English.
77 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
78 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
79 at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
80 described in greate
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.