Pneumatic fluid power systems - Directional control valves - Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors

ISO 20401:2017 specifies the pin assignment for pneumatic directional control valves when used together with 8 mm and 12 mm diameter electrical round connectors according to IEC 60947-5-2. This definition is valid for connectors as shown in IEC 60947-5-2:2004, Figures D.2 and D.4, which are shown in Clause 4.

Transmissions pneumatiques — Distributeurs de commande directionnels — Spécification de l'affectation des broches des connecteurs électriques ronds de diamètres 8 mm et 12 mm

Fluidna tehnika - Pnevmatika - Potni ventili - Specifikacija za kontakte za okrogle električne konektorje s premeroma 8 mm in 12 mm

Standard ISO 20401:2017 določa dodelitev zatičev za pnevmatske krmilne ventile, kadar se uporabljajo skupaj z električnimi okroglimi konektorji premera 8 mm in 12 mm v skladu z IEC 60947-5-2. Ta opredelitev velja za konektorje, kot so prikazani v IEC 60947-5-2:2004, sliki D.2 in D.4, ki sta prikazani v točki 4.

General Information

Status
Published
Publication Date
08-Mar-2023
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Mar-2023
Due Date
11-May-2023
Completion Date
09-Mar-2023

Relations

Buy Standard

Standard
ISO 20401:2023
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 20401:2017 - Pneumatic fluid power systems -- Directional control valves -- Specification of pin assignment for 8 mm and 12 mm diameter electrical round connectors
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 20401:2023
01-april-2023
Fluidna tehnika - Pnevmatika - Potni ventili - Specifikacija za kontakte za okrogle
električne konektorje s premeroma 8 mm in 12 mm
Pneumatic fluid power systems - Directional control valves - Specification of pin
assignment for 8 mm and 12 mm diameter electrical round connectors
Transmissions pneumatiques — Distributeurs de commande directionnels —
Spécification de l'affectation des broches des connecteurs électriques ronds de
diamètres 8 mm et 12 mm
Ta slovenski standard je istoveten z: ISO 20401:2017
ICS:
23.100.50 Krmilni sestavni deli Control components
SIST ISO 20401:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 20401:2023

---------------------- Page: 2 ----------------------
SIST ISO 20401:2023
INTERNATIONAL ISO
STANDARD 20401
Second edition
2017-07
Pneumatic fluid power systems —
Directional control valves —
Specification of pin assignment for 8
mm and 12 mm diameter electrical
round connectors
Transmissions pneumatiques — Distributeurs de commande
directionnels — Spécification de l’affectation des broches des
connecteurs électriques ronds de diamètres 8 mm et 12 mm
Reference number
ISO 20401:2017(E)
©
ISO 2017

---------------------- Page: 3 ----------------------
SIST ISO 20401:2023
ISO 20401:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 20401:2023
ISO 20401:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Integral connectors for plug-in proximity switches . 2
5 Graphical symbols . 2
6 Electrical contacts (pin allocation) . 2
6.1 Identification . 2
6.2 Pin allocation for valves with a single solenoid . 3
6.3 Pin allocation for valves with double solenoids and one connector . 3
6.4 Pin allocation for valves with double solenoids and two connectors . 3
Bibliography . 5
© ISO 2017 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 20401:2023
ISO 20401:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such paten
...

INTERNATIONAL ISO
STANDARD 20401
Second edition
2017-07
Pneumatic fluid power systems —
Directional control valves —
Specification of pin assignment for 8
mm and 12 mm diameter electrical
round connectors
Transmissions pneumatiques — Distributeurs de commande
directionnels — Spécification de l’affectation des broches des
connecteurs électriques ronds de diamètres 8 mm et 12 mm
Reference number
ISO 20401:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 20401:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 20401:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Integral connectors for plug-in proximity switches . 2
5 Graphical symbols . 2
6 Electrical contacts (pin allocation) . 2
6.1 Identification . 2
6.2 Pin allocation for valves with a single solenoid . 3
6.3 Pin allocation for valves with double solenoids and one connector . 3
6.4 Pin allocation for valves with double solenoids and two connectors . 3
Bibliography . 5
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 20401:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.