Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor

This European Standard deals with the safety requirements for electrically operated commercial refrigerating appliances and ice-makers that have an incorporated motor-compressor or that are supplied in two units for assembly as a single appliance in accordance with the instructions (split system).

Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-89: Besondere Anforderungen für gewerbliche Kühl-/Gefriergeräte mit eingebautem oder getrenntem Verflüssigersatz oder Motorverdichter

Appareils électrodomestiques et analogues - Sécurité - Partie 2-89: Règles particulières pour les appareils de réfrigération à usage commercial avec une unité de condensation du fluide frigorigène ou un compresseur incorporés ou à distance

Gospodinjski in podobni električni aparati - Varnost - 2-89. del: Posebne zahteve za komercialne hladilne naprave z vgrajeno ali zunanjo hladilno kondenzatorsko enoto ali kompresorjem - Dopolnilo AA

General Information

Status
Not Published
Public Enquiry End Date
29-Jun-2020
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
06-May-2020
Due Date
23-Sep-2020
Completion Date
15-May-2020

Buy Standard

Draft
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
01-junij-2020

Gospodinjski in podobni električni aparati - Varnost - 2-89. del: Posebne zahteve

za komercialne hladilne naprave z vgrajeno ali zunanjo hladilno kondenzatorsko
enoto ali kompresorjem - Dopolnilo AA

Household and similar electrical appliances - Safety - Part 2-89: Particular requirements

for commercial refrigerating appliances with an incorporated or remote refrigerant

condensing unit or compressor

Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-89:

Besondere Anforderungen für gewerbliche Kühl-/Gefriergeräte mit eingebautem oder
getrenntem Verflüssigersatz oder Motorverdichter

Appareils électrodomestiques et analogues - Sécurité - Partie 2-89: Règles particulières

pour les appareils de réfrigération à usage commercial avec une unité de condensation

du fluide frigorigène ou un compresseur incorporés ou à distance
Ta slovenski standard je istoveten z: prEN IEC 60335-2-89:2020/prAA:2020
ICS:
97.130.20 Hladilne naprave za trgovine Commercial refrigerating
appliances
oSIST prEN IEC 60335-2- en,fr
89:2020/oprAA:2020

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
---------------------- Page: 2 ----------------------
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
EUROPEAN STANDARD DRAFT
prEN IEC 60335-2-89:2020
NORME EUROPÉENNE
EUROPÄISCHE NORM
prAA
May 2020
ICS
English Version
Household and similar electrical appliances - Safety - Part 2-89:
Particular requirements for commercial refrigerating appliances
with an incorporated or remote refrigerant condensing unit or
compressor

Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und

Partie 2-89: Règles particulières pour les appareils de ähnliche Zwecke - Teil 2-89: Besondere Anforderungen für

réfrigération à usage commercial avec une unité de gewerbliche Kühl-/Gefriergeräte mit eingebautem oder

condensation du fluide frigorigène ou un compresseur getrenntem Verflüssigersatz oder Motorverdichter

incorporés ou à distance

This draft amendment prAA, if approved, will modify the European Standard prEN IEC 60335-2-89:2020; it is submitted to CENELEC

members for enquiry.
Deadline for CENELEC: 2020-07-24.
It has been drawn up by CLC/TC 61.

If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which

stipulate the conditions for giving this amendment the status of a national standard without any alteration.

This draft amendment was established by CENELEC in three official versions (English, French, German).

A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to

the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the

Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to

provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and

shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Project: 70831 Ref. No. prEN IEC 60335-2-89:2020/prAA:2020 E
---------------------- Page: 3 ----------------------
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
prEN IEC 60335-2-89:2020/prAA:2020 (E)
1 European foreword

2 This document (prEN IEC 60335-2-89:2020/A11:2020) has been prepared by CLC/TC 61 "Safety of

3 household and similar electrical appliances".
4 This document is currently submitted to the CENELEC Enquiry
5 The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)

7 This document will supersede EN 60335-2-89:2010 and all of its amendments and corrigenda (if any).

8 This amendment supplements or modifies the corresponding clauses of the standards below:

9 – EN 60335-1:2012+A11:2014+ A13:2017+A1:2019+A14:2019+A2:2019 (Part 1)
10 – EN IEC 60335-2-89:2019+Cor1 (Part 2)

11 – Secretary Note: This standard shall be read in conjunction with EN IEC 60335-2-

12 89:2020.(PR=70830)

13 The numbering system for European clauses, subclauses, notes, tables, figures and annexes that are

14 additional to those in the IEC standard are prefixed with the letter “Z”.

15 This document has been prepared under a mandate given to CENELEC by the European Commission

16 and the European Free Trade Association, and supports essential requirements of EU Directive(s).

17 For the relationship with EU Directive(s) see informative Annexes ZZA and ZZB, which are an integral

18 part of this document.
---------------------- Page: 4 ----------------------
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
prEN IEC 60335-2-89:2020/prAA:2020 (E)
19 Text of prAA:2020 of prEN IEC 60335-2-89:2020
20 1 Modification to the Introduction
21 Addition:

22 Products within the scope of this standard may incorporate pressurized components for which the

23 Pressure Equipment Directive, 2014/68/EU, applies:

24 Refrigerating systems having a pressure greater than 0,05 MPa are considered to be assemblies

25 falling within the scope of the Pressure Equipment Directive, 2014/68/EU. However, according to

26 Article 1, item 2 (f) of the Directive, equipment classified no higher than category I under Article 13 of

27 the PED and covered by the Low Voltage Directive or Machinery Directive are excluded from its

28 scope.

29 Compliance with this standard does not give a means of conformity with the essential requirements of

30 the Pressure Equipment Directive for those appliances that fall within its scope.

32 2 Modification to the Scope
34 Add the following NOTE after NOTE 101:

35 NOTE Z101 Commercial use of these refrigerating appliances is for example their use in restaurants, canteens, hospitals and

36 commercial enterprises such as bakeries, butcheries, supermarkets etc.
38 Add the following paragraph before NOTE 102:

39 In many countries additional requirements on the safe use of the equipment covered may be specified by the

40 national health authorities, the national authorities responsible for the protection of labour, the national water

41 supply authorities and similar authorities.
42 NOTE 102:
43 Delete the second dashed item:
44 Add the following dashed item:
45 – for scrapping of appliances, additional requirements may be necessary.
47 Add the following new paragraph:

48 Products covered by this standard do not create a noise hazard; therefore no specific provisions

49 concerning noise are given.
---------------------- Page: 5 ----------------------
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
prEN IEC 60335-2-89:2020/prAA:2020 (E)
50 3 Modification to clause 2, "Normative references"
51 Add the following standards:

52 EN 614-1:2006+A1:2009, Safety of machinery – Ergonomic design principles – Part 1: Terminology

53 and general principles

54 EN 614-2:2000+A1:2008, Safety of machinery - Ergonomic design principles - Part 2: Interactions

55 between the design of machinery and work tasks

56 EN ISO 14159:2008, Safety of machinery - Hygiene requirements for the design of machinery (ISO

57 14159:2002)
59 4 Modification to clause 3, "Terms and Definitions"
60 Add the following definitions:
61 3.Z101 guard

62 part of the appliance specifically designed to provide protection by means of a physical barrier

63 3.Z102 operator

64 person installing, operating, adjusting, maintaining, cleaning or moving the appliance

65 3.Z103 commercial use
66 intended use of appliances covered by this standard in a professional way

67 Note 1 : For the purpose of this standard commercial use may be read as not intended for domestic use.

68 5 Modification to clause 4, "General requirement"
69 Replace the first paragraph of Part 1by the following:

70 Appliances shall be constructed so that they function safely so as to cause no danger to persons or

71 surroundings during normal use, even in the event of carelessness, and during installation, adjusting,

72 maintenance, cleaning, repairing or transportation.
73 6 Modification to clause 7, "Marking and instructions"
74 7.1 Replace the fourth and fifth dashed items in part 1 by:

75 - business name and full address of the manufacturer and, where applicable, his authorized

76 representative;
77 - model or type reference, serial number, if any, and production year;

78 NOTE Z101 Production year is the year when the production process is completed. The production year can be a part of the

79 serial number.
80 Add a new dashed item:
81 - designation of the appliance.

82 NOTE Z102 The designation may be a combination of letters and/or numbers and shall enable to identify the machine as

83 specified in the instructions.
---------------------- Page: 6 ----------------------
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
prEN IEC 60335-2-89:2020/prAA:2020 (E)
84 7.12 Add the following to the addition:
85 The instructions shall contain the following:

86 - business name and full address of the manufacturer and, where applicable, his authorized

87 representative;

88 - model or type reference of the appliance as marked on the appliance itself, except for the serial

89 number;

90 - designation of the appliance together with its explanation in case it is given by a combination of

91 letters and/or numbers;

92 - a general description of the appliance, when needed due to the complexity of the appliance;

93 - specific precautions if required during installation, operation, adjusting, user maintenance,

94 cleaning, repairing or moving;

95 - when needed drawings, diagrams, descriptions and explanations necessary for the safe use and

96 user maintenance of the appliance;

97 - the possible reasonably foreseeable misuse and, whenever relevant, a warning against the

98 effects it may have on the safe use of the appliance;

99 The words “Original instructions” shall appear on the language version(s) verified by the manufacturer

100 or by the authorized representative.

101 When a translation of the original instructions has been provided by a person introducing the

102 appliance on the market; the meaning of the sentence “Translation of the original instructions” has to

103 appear in the relevant instructions delivered with the appliance.

104 The instructions for maintenance/service to be done by specialized personnel, mandated by the

105 manufacturer or the authorized representative may be supplied in only one Community language

106 which the specialized personnel understand.

107 The instructions shall indicate the type and frequency of inspections and maintenance required for

108 safe operation including the preventive maintenance measures.
109 Add the new following sub-clauses:
110 7.12.Z101 Information shall be given:

111 – on use, transportation, assembly, dismantling when out of service, testing or foreseeable

112 breakdowns, if these operations have consequences on stability of the appliance in order to

113 avoid overturning, falling or uncontrolled movements of the appliance or of its component

114 parts;

115 – on how to maintain adequate mechanical stability when in use, during transportation,

116 assembly, dismantling, scrapping and any other action involving the appliance;

---------------------- Page: 7 ----------------------
oSIST prEN IEC 60335-2-89:2020/oprAA:2020
prEN IEC 60335-2-89:2020/prAA:2020 (E)

117 – on the protective measures to be taken by the user, including, where appropriate, the personal

118 protective equipment to be provided;

119 – on the operating method to be followed in the event of accident or breakdown; if a blockage is

120 likely to occur the operating method to safely unblock the appliance;

121 – on the specifications on the spare parts to be used, when these affect the health and safety of

122 the operator;
123 – that the A-weighted emission sound pressure level is below 70 dB(A);

124 7.12.1.Z102 Instructions shall be given, when necessary, concerning safe handling and

125 transportation on the packed appliance or have to be delivered together with the package.

126 7.12.1.Z103 If the installation instructions state that appliance can be placed on top of a other

127 appliance, they shall state which appliances are suitable. Instructions shall be given for the assembly

128 of the appliances. The instructions shall state how to obtain any fixing attachments required, unless

129 they are supplied with the appliance.

130 7.12.Z104 The instructions shall include a warning that the appliance shall be disconnected from its

131 power source during cleaning or maintenance and when replacing parts. If the removal of the plug is

132 foreseen, it shall be clearly indicated that the removal of the plug has to be such that an operator can

133 check from any of the points to which he has access that the plug remains removed.

134 If this is not possible, due to the construction of the appliance or its installation, a disconnection with a

135 locking system in the isolated position shall be provided.
136
137 7 Modification to clause 20, "Stability and mechanical hazards"
138 Add new sub clause:
139 20.1.Z101

140 Appliances and their components and fittings shall have adequate mechanical stability during

141 transportation, assembly
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.