M/396 - Machinery

2021-12-20: This prAA includes common mods to EN IEC 62841-2-19 (PR=75430)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

2021-12-20: This prAA includes common mods to EN IEC 62841-2-20 (PR=75425)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

2021-12-20: This prAA includes common mods to EN IEC 62841-2-19 (PR=75430)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

IEC 62841-2-22:2025 applies to hand-held cut-off machines fitted with - one bonded reinforced wheel of Type 41 or Type 42; or - one or more diamond cutting wheels with peripheral gaps, if any, • having no positive rake angle; and • not exceeding 10 mm for cut-off machines other than flush cutters, power cutters and wall chasers; and with - a rated no-load speed not exceeding a peripheral speed of the wheel of 100 m/s at rated capacity; and - a rated capacity not exceeding 430 mm. NOTE 101 An example of a permitted diamond cutting wheel construction is shown in Figure 106. These tools are intended to cut materials such as metals, concrete, masonry, glass and tile. This document does not apply to: - cut-off machines that can be converted to a grinder, sander or polisher, which are covered by IEC 62841-2-3; - circular saws which are covered by IEC 62841-2-5; and - die grinders and small rotary tools which are covered by IEC 62841-2-23; - tools intended to cut wood, except for utility cutters; - cut-off machines fitted with a bonded reinforced wheel of Type 42 with a diameter exceeding 230 mm. This document is to be used in conjunction with IEC 62841-1:2014.

2021-12-20: This prAA includes common mods to EN IEC 62841-2-20 (PR=75425)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held fastener driving tools. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
Addition: This document applies to hand-held fastener driving tools
- intended for driving fasteners into or through concrete, fabric, fiberboard, metal, plastic, wood, wood products, cartons, and other materials; and
- whose energy to drive the fastener is derived directly or indirectly from an electric motor or magnetic drive.
This document does not apply to pneumatically driven tools where the compressed gas comes from an external source, such as a compressor or a tank.
This document does not apply to tools powered by combustible gases, even if electrically ignited.
NOTE 101 Tools powered by compressed air or combustible gases are covered by ISO 11148-13:2017.

This document applies to conductor car that are used to access overhead line conductors, shield wires or shield wires with integrated communication systems to undertake work involving rectification of defects and/or installing components and fittings. This document covers also bicycle type access equipment where it is applicable.

IEC 62841-2-16:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held fastener driving tools. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly. IEC 62841-1:2014, Clause 1 is applicable, except as follows: Addition: This document applies to hand-held fastener driving tools - intended for driving fasteners into or through concrete, fabric, fiberboard, metal, plastic, wood, wood products, cartons, and other materials; and - whose energy to drive the fastener is derived directly or indirectly from an electric motor or magnetic drive. This document does not apply to pneumatically driven tools where the compressed gas comes from an external source, such as a compressor or a tank. This document does not apply to tools powered by combustible gases, even if electrically ignited. NOTE 101 Tools powered by compressed air or combustible gases are covered by ISO 11148-13:2017.

This document applies to conductor car that are used to access overhead line conductors, shield wires or shield wires with integrated communication systems to undertake work involving rectification of defects and/or installing components and fittings. This document covers also bicycle type access equipment where it is applicable.

NEW!IEC 60335-2-58:2017 is available as IEC 60335-2-58:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60335-2-58:2017 deals with the safety of electrically operated dishwashing machines for washing plates, dishes, glassware, cutlery and similar articles, with or without means for water heating or drying, not intended for household use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. These appliances are used for example in restaurants, canteens, hospitals, and commercial enterprises such as bakeries, butcheries, etc. Examples of such appliances are conveyor dishwashers; batch dishwashers and brush machines. Requirements to avoid backsiphonage of non-potable water into the water mains are specified in Annex BB. The electrical part of appliances making use of other forms of energy is also within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by these types of appliances. Attention is drawn to the fact that for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. This standard does not apply to the following: appliances designed exclusively for industrial purposes, for example machines used in the food industry for cleaning receptacles that serve as packaging for final products (e.g. bottle-cleaning machines), and machines used in manufacturing processes; sterilizers and washer-disinfectors used to treat medical materials (IEC 61010-2-040); dishwashers that do not form one functional unit, for example where a transportation device transfers the load from one separate unit to another; separately driven transport devices not confined in the appliance; appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). This fourth edition cancels and replaces the third edition published in 2002 including its Amendment 1 (2008) and its Amendment 2 (2015). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: The text has been aligned with Edition 5.2 of Part 1; Requirements and tests for vertical-lift doors with and without a counterbalance system are clarified (20.103, 20.104); Some notes have been converted to normative text or deleted (7.15, 9, 10.1, 11.7, 15.3, 19.4, 20.1, 20.102, 22.106, 22.107, 23.3). This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the fifth edition (2010) of that standard The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication.
Key words: Dishwashing Machine, Safety, Commercial

This European Standard deal with the safety of electrically operated dishwashing machines for washing plates, dishes, glassware, cutlery and similar articles, with or without means for water heating or drying, not intended for household use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances

This European Standard deal with the safety of electrically operated dishwashing machines for washing plates, dishes, glassware, cutlery and similar articles, with or without means for water heating or drying, not intended for household use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances

Not available

This part of IEC 60204 applies to electrical, electronic, programmable electronic equipment and systems to hoisting machines and related equipment, including a group of hoisting machines working together in a co-ordinated manner
NOTE 1 In this part of IEC 60204, the term "electrical" includes both electrical and electronic matters (i.e. "electrical equipment" means both the electrical, electronic and programmable electronic equipment).
NOTE 2 In the context of this part of IEC 60204, the term “person” refers to any individual and includes those persons who are assigned and instructed by the user or user’s agent(s) in the use and care of the hoisting machine in question.
The equipment covered by this part of IEC 60204 commences at the point of connection of the supply to the electrical equipment of the hoisting machine (crane-supply-switch) and includes systems for power supply and control feeders situated outside of the hoisting machine, for example, flexible cables or conductor wires or conductor bars (see Figure 3).
NOTE 3 The requirements for the electrical supply installation of electrical equipment of a hoisting machine are given in IEC 60364.
This standard is applicable to equipment or parts of equipment not exceeding 1 000 V AC or 1 500 V DC between lines and with nominal frequencies not exceeding 200 Hz.
NOTE 4 Special requirements for electrical equipment of hoisting machines intended to be operated at higher voltages, see IEC 60204-11 (Annex D)
This part of IEC60204 does not cover all the requirements (for example guarding, interlocking, or control) that are needed or required by other standards or regulations in order to protect persons from hazards other than electrical hazards. Each type of hoisting machine has unique requirements to be accommodated to provide adequate safety. This part of 60204 doesn´t cover noise risks and vibration risks.
Additional and special requirements can apply to the electrical equipment of hoisting machines including those that
- handle or transport potentially explosive material (e.g. paint or sawdust);
- are intended for use in potentially explosive and/or flammable atmospheres;
- have special risks when transporting or moving certain materials
- are intended for use in mines.
For the purposes of this standard, hoisting machines include cranes of all types, winches of all types and storage and retrieval machines. The following product groups are included:
- overhead travelling cranes;
- mobile cranes;
- tower cranes;
- slewing luffing cranes;
- gantry cranes;
- offshore cranes;
- floating cranes;
- winches of all types;
- hoists and accessories;
- loader cranes;
- cable cranes;
- load holding devices;
- storage and retrieval machines;
- monorail hoists;
- straddle carriers;
- rubber tyred gantry cranes (RTGs).
NOTE 5 Definition of the different crane types see ISO 4306-1
This standard does not cover individual items of electrical equipment other than their selection for use and their erection.

This European Standard deals with the safety of sealed (hermetic and semi-hermetic type) motor-compressors, their protection and control systems, if any, which are intended for use in equipment for household and similar purposes and which conform with the standards applicable to such equipment. It applies to motor-compressors tested separately, under the most severe conditions that may be expected to occur in normal use, their rated voltage being not more than 250 V for single-phase motor-compressors and 480 V for other motor-compressors

This European Standard deals with the safety of sealed (hermetic and semi-hermetic type) motor-compressors, their protection and control systems, if any, which are intended for use in equipment for household and similar purposes and which conform with the standards applicable to such equipment. It applies to motor-compressors tested separately, under the most severe conditions that may be expected to occur in normal use, their rated voltage being not more than 250 V for single-phase motor-compressors and 480 V for other motor-compressors

This part of IEC 60204 applies to electrical, electronic, programmable electronic equipment and systems to hoisting machines and related equipment, including a group of hoisting machines working together in a co-ordinated manner NOTE 1 In this part of IEC 60204, the term "electrical" includes both electrical and electronic matters (i.e. "electrical equipment" means both the electrical, electronic and programmable electronic equipment). NOTE 2 In the context of this part of IEC 60204, the term “person” refers to any individual and includes those persons who are assigned and instructed by the user or user’s agent(s) in the use and care of the hoisting machine in question. The equipment covered by this part of IEC 60204 commences at the point of connection of the supply to the electrical equipment of the hoisting machine (crane-supply-switch) and includes systems for power supply and control feeders situated outside of the hoisting machine, for example, flexible cables or conductor wires or conductor bars (see Figure 3). NOTE 3 The requirements for the electrical supply installation of electrical equipment of a hoisting machine are given in IEC 60364. This standard is applicable to equipment or parts of equipment not exceeding 1 000 V AC or 1 500 V DC between lines and with nominal frequencies not exceeding 200 Hz. NOTE 4 Special requirements for electrical equipment of hoisting machines intended to be operated at higher voltages, see IEC 60204-11 (Annex D) This part of IEC60204 does not cover all the requirements (for example guarding, interlocking, or control) that are needed or required by other standards or regulations in order to protect persons from hazards other than electrical hazards. Each type of hoisting machine has unique requirements to be accommodated to provide adequate safety. This part of 60204 doesn´t cover noise risks and vibration risks. Additional and special requirements can apply to the electrical equipment of hoisting machines including those that - handle or transport potentially explosive material (e.g. paint or sawdust); - are intended for use in potentially explosive and/or flammable atmospheres; - have special risks when transporting or moving certain materials - are intended for use in mines. For the purposes of this standard, hoisting machines include cranes of all types, winches of all types and storage and retrieval machines. The following product groups are included: - overhead travelling cranes; - mobile cranes; - tower cranes; - slewing luffing cranes; - gantry cranes; - offshore cranes; - floating cranes; - winches of all types; - hoists and accessories; - loader cranes; - cable cranes; - load holding devices; - storage and retrieval machines; - monorail hoists; - straddle carriers; - rubber tyred gantry cranes (RTGs). NOTE 5 Definition of the different crane types see ISO 4306-1 This standard does not cover individual items of electrical equipment other than their selection for use and their erection.

IEC 62841-4-8:2025 specifies safety requirements and their verification for the design and construction of hand fed, shredders/chippers with an integral electric motor, with or without vacuum assisted collection, which are designed to reduce organic material to smaller pieces and are used in a stationary position by an operator standing on the ground. This document applies to shredders/chippers with feed intake openings or feed safety openings that in total will fit into a square of 250 mm x 250 mm.
NOTE 101 The requirements for the measurement of the square of 250 mm x 250 mm are specified in 19.101.1.
In this document, shredders/chippers are referred to collectively as machine(s).
This document does not cover requirements for
- machines powered by combustion engines; or
- machines driven by an external power source; or
- machines with powered discharge intended to broadcast material or load vehicles; or
- machines with mechanically powered feed intake or attachments; or
- wood chippers for forestry, agriculture, horticulture and landscaping.
This document is to be used in conjunction with IEC 62841‑1:2014.
This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for shredders/chippers.

2022-08-22: This prAA covers common mods to EN IEC 62841-4-8 (PR=75587)
D164/C043: DOW = DOR + 48 months

This document applies to conductor car that are used to access overhead line conductors, shield wires or shield wires with integrated communication systems to undertake work involving rectification of defects and/or installing components and fittings. This document covers also bicycle type access equipment where it is applicable.

This document applies to conductor car that are used to access overhead line conductors, shield wires or shield wires with integrated communication systems to undertake work involving rectification of defects and/or installing components and fittings. This document covers also bicycle type access equipment where it is applicable.

IEC 62841-4-8:2025 specifies safety requirements and their verification for the design and construction of hand fed, shredders/chippers with an integral electric motor, with or without vacuum assisted collection, which are designed to reduce organic material to smaller pieces and are used in a stationary position by an operator standing on the ground. This document applies to shredders/chippers with feed intake openings or feed safety openings that in total will fit into a square of 250 mm x 250 mm. NOTE 101 The requirements for the measurement of the square of 250 mm x 250 mm are specified in 19.101.1. In this document, shredders/chippers are referred to collectively as machine(s). This document does not cover requirements for - machines powered by combustion engines; or - machines driven by an external power source; or - machines with powered discharge intended to broadcast material or load vehicles; or - machines with mechanically powered feed intake or attachments; or - wood chippers for forestry, agriculture, horticulture and landscaping. This document is to be used in conjunction with IEC 62841‑1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for shredders/chippers.

1.1   This document specifies the electrical requirements for the design of automatic electrostatic application systems for liquid coating materials which can be ignited in an atomised state, used within a temperature range from 5 °C to 40 °C.
This document considers automatic electrostatic application systems for processing ignitable liquid coating materials, where the conductivity of the complete system is limited up to 50 nS/cm. Together with additional measures like e.g. potential separation systems, these requirements can also be applied to ignitable liquid coating materials, where the conductivity of the complete system is limited up to 2 000 μS/cm.
Ignition hazards related to the generated explosive atmosphere and the protection of persons against electric shock are considered.
1.2   This document specifies
-   requirements for an interface to machinery according to EN 16985:2018,
-   additional requirements for machinery covered by EN 1953:2025 and EN 12621:2025.
1.3   This document also specifies requirements for a safe operation of electrostatic application systems, including the electrical installation. The requirements consider both the processing of coating materials and the cleaning and purge processes.
1.4   This document applies to three types of spraying systems; see 5.1.1.
Spraying systems are classified as equipment of group II, category 2G (for intended use in zone 1 or zone 2) or category 3G (for intended use in zone 2).
Only electrostatic spraying systems operating with a d.c. sinusoidal ripple of not more than 10 % of the r.m.s. value are considered.
1.5   For electrostatic application systems used in food and pharmaceutical industry, additional requirements may apply.
1.6   This document does not apply to
-   potential separation systems;
-   selection, installation and application of other electrical and non-electrical equipment in areas with explosion hazard, see EN 60079-14:2014 and EN 16985:2018;
-   quality assurance systems for electrostatic spraying equipment (see EN ISO/IEC 80079-34:2020, ZB.11).

2022-08-22: This prAA covers common mods to EN IEC 62841-4-8 (PR=75587)
D164/C043: DOW = DOR + 48 months

1.1   This document specifies the electrical requirements for hand-held or hand-operated electrostatic application equipment for non-ignitable liquid coating materials which
—   do not generate an explosive atmosphere inside the spraying area,
—   are used to process coating materials with a conductivity of the complete system up to 2 000 µS/cm,
—   operate with direct current having a d.c. sinusoidal ripple of not more than 10 % of the r.m.s. value and
—   are used within a temperature range from 5 °C to 40 °C.
1.2   This document specifies
—   requirements for an interface to machinery according to EN 16985:2018,
—   additional requirements for machinery according to EN 1953:—  and EN 12621:— .
1.3   This document also specifies requirements for a safe operation of electrostatic application equipment, including the electrical installation. The requirements consider both the processing of coating materials and the cleaning and purge processes.
1.4   For electrostatic application equipment used in food and pharmaceutical industry, additional requirements can apply.
1.5   This document does not apply to
—   electrostatic hand-held spraying equipment for ignitable materials, see EN 50050:2013, Parts 1 to 3;
—   cleaning systems for spraying devices;
—   quality assurance systems for electrostatic spraying equipment (see EN ISO/IEC 80079-34:2020, Annex ZB 11).

1.1 This document specifies the electrical requirements for the design of automatic electrostatic application systems for liquid coating materials which can be ignited in an atomised state, used within a temperature range from 5 °C to 40 °C. This document considers automatic electrostatic application systems for processing ignitable liquid coating materials, where the conductivity of the complete system is limited up to 50 nS/cm. Together with additional measures like e.g. potential separation systems, these requirements can also be applied to ignitable liquid coating materials, where the conductivity of the complete system is limited up to 2 000 μS/cm. Ignition hazards related to the generated explosive atmosphere and the protection of persons against electric shock are considered. 1.2 This document specifies - requirements for an interface to machinery according to EN 16985:2018, - additional requirements for machinery covered by EN 1953:2025 and EN 12621:2025. 1.3 This document also specifies requirements for a safe operation of electrostatic application systems, including the electrical installation. The requirements consider both the processing of coating materials and the cleaning and purge processes. 1.4 This document applies to three types of spraying systems; see 5.1.1. Spraying systems are classified as equipment of group II, category 2G (for intended use in zone 1 or zone 2) or category 3G (for intended use in zone 2). Only electrostatic spraying systems operating with a d.c. sinusoidal ripple of not more than 10 % of the r.m.s. value are considered. 1.5 For electrostatic application systems used in food and pharmaceutical industry, additional requirements may apply. 1.6 This document does not apply to - potential separation systems; - selection, installation and application of other electrical and non-electrical equipment in areas with explosion hazard, see EN 60079-14:2014 and EN 16985:2018; - quality assurance systems for electrostatic spraying equipment (see EN ISO/IEC 80079-34:2020, ZB.11).

1.1 This document specifies the electrical requirements for hand-held or hand-operated electrostatic application equipment for non-ignitable liquid coating materials which — do not generate an explosive atmosphere inside the spraying area, — are used to process coating materials with a conductivity of the complete system up to 2 000 µS/cm, — operate with direct current having a d.c. sinusoidal ripple of not more than 10 % of the r.m.s. value and — are used within a temperature range from 5 °C to 40 °C. 1.2 This document specifies — requirements for an interface to machinery according to EN 16985:2018, — additional requirements for machinery according to EN 1953:— and EN 12621:— . 1.3 This document also specifies requirements for a safe operation of electrostatic application equipment, including the electrical installation. The requirements consider both the processing of coating materials and the cleaning and purge processes. 1.4 For electrostatic application equipment used in food and pharmaceutical industry, additional requirements can apply. 1.5 This document does not apply to — electrostatic hand-held spraying equipment for ignitable materials, see EN 50050:2013, Parts 1 to 3; — cleaning systems for spraying devices; — quality assurance systems for electrostatic spraying equipment (see EN ISO/IEC 80079-34:2020, Annex ZB 11).

IEC 60825-4:2022 is available as IEC 60825-4:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60825-4:2022 deals with basic issues concerning laser guards, including human access, interlocking and labelling, and gives general guidance on the design of protective housings and enclosures for high-power lasers. Laser guards may also comply with standards for laser protective eyewear, but such compliance is not necessarily sufficient to satisfy the requirements of this document. This part of IEC 60825 specifies the requirements for laser guards, permanent and temporary (for example for service), that enclose the process zone of a laser processing machine, and specifications for proprietary laser guards. This document applies to all component parts of a guard including clear (visibly transmitting) screens and viewing windows, panels, laser curtains and walls. In addition, this document indicates
- how to assess and specify the protective properties of a laser guard, and
- how to select a laser guard.

IEC 60825-4:2022 is available as IEC 60825-4:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60825-4:2022 deals with basic issues concerning laser guards, including human access, interlocking and labelling, and gives general guidance on the design of protective housings and enclosures for high-power lasers. Laser guards may also comply with standards for laser protective eyewear, but such compliance is not necessarily sufficient to satisfy the requirements of this document. This part of IEC 60825 specifies the requirements for laser guards, permanent and temporary (for example for service), that enclose the process zone of a laser processing machine, and specifications for proprietary laser guards. This document applies to all component parts of a guard including clear (visibly transmitting) screens and viewing windows, panels, laser curtains and walls. In addition, this document indicates - how to assess and specify the protective properties of a laser guard, and - how to select a laser guard.

2021-05-10: CMs to this A2 are included in prAB (PR=73987)
NEXT ACTION: TB ACTION (ADVICE ON NEGATIVE ASSESSMENT) BY 2021-01-31
HAS NAC ASSESSMENT BY 2019-09-26
2017-05-16 - Cannot allocate for publication due to negative assessment from Consultant.

This European Standard deals with the safety of electrically operated commercial forced convection ovens, steam cookers, steam-convection ovens and, exclusive of any other use, steam generators, not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. Appliances within the scope of this standard are typically used in restaurants, canteens, hospitals and commercial enterprises such as bakeries, butcheries, etc

This European Standard deals with the safety of electrical operated tumble dryers intended to be used by trained users in i.e. hotels, hospitals, factories, in light industry and on farms. It also covers tumble dryers which are declared for commercial use in public areas and operated by lay persons e.g. in laundrettes, communal laundry rooms. The rated voltage shall not be more than 250 V for single phase and 480 V for others.

This European Standard deals with the safety of electric fans for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances

NEXT ACTION: TB ACTION (ADVISE ON NEGATIVE ASSESSMENT) BY 2021-01-31
2019-10-03: lack of compliance for LVD on PUB assessment
HAS CONSULTANT ASSESSMENT BY 2019-06-17 (E&Y LATE)
2019-01-23 CV: CCMC to request post factum assessment (and if positively assessed to proceed to BT for finalization)
2017-05-02: D156/C084 - Ratified standards not being made available.
2017-09-07: Publication pending due to missing Annex ZZ

This European Standard deals with the safety of gas, oil and solid-fuel burning appliances having electrical connections, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. This standard covers the electrical safety and some other safety aspects of these appliances. All safety aspects of these appliances, including those relevant to the noise emitted, are only covered when the appliance also complies with the relevant product standard for the fuel-burning appliance.

This standard deals with the safety of electrically operated commercial multi-purpose cooking pans not intended for household and similar use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. This standard also deals with pressurized appliances and appliances with pressurized parts. These appliances are used for processing food for commercial consumption, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises such as bakeries, butcheries, etc

This European Standard deals with the safety of electrical operated washing machines intended to be used by trained users in e.g. hotels, hospitals, factories, in light industry and on farms. It also covers washing machines declared for commercial use in public areas and operated by lay persons e.g. in laundrettes, communal laundry rooms. Their rated voltage being not more than 250 V for single phase and 480 V for others.

This European Standard Deals with the safety of electrically operated commerical multi-purpose cooking pans not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. Appliances within the scope of this standard are typically used in restaurants, canteens, hospitals, and commercial enterprises such as bakeries, butcheries, etc. The electrical part of appliances making use of other forms of energy is also within the scope of this standard.

This European Standard deals with the safety of electric heat pumps, sanitary hot water heat pumps and air conditioners, incorporating motor-compressors as well as hydronic fan coils units, dehumidifiers (with or without motor-compressors), thermoelectric heat pumps and partial units. Their maximum rated voltage being not more than 300 V for single phase appliances and 600 V for multi-phase appliances. Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.

This European Standard deals with the safety of electrically operated commercial hot cupboards not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. Hot cupboards with heated tops, heated display cases, heated crockery dispensers and heated shelves and tables are also within the scope of this standard. The appliances within the scope of this standard are typically used in restaurants, canteens, hospitals and similar commercial enterprises.

New European Amendment for introduce the CMs in according to LVD and MD directives

This European Standard deals with the safety of electrically operated commercial boiling pans not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. Appliances which are within the scope of this standard are typically used in restaurants, canteens, hospitals and commercial enterprises such as bakeries, butcheries,etc.

This European Standard deals with the safety of electrically operated commercial grillers and toasters not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. Rotary or continuous grillers and toasters and similar appliances intended for grilling by radiant heat such as rotisseries, salamanders, etc. are within the scope of this standard. Appliances within the scope of this standard are typically used in restaurants, canteens, hospitals and commercial enterprises such as bakeries, butcheries, etc.