iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1417:2000

(Main)

Rubber and plastics machines - Two roll mills - Safety requirements

Rubber and plastics machines - Two roll mills - Safety requirements

This standard covers the essential health and safety requirements for all two roll mills for the processing of rubber and plastics. Significant hazards are listed in clause 4 and are covered by this standard.   Figure 1 [not shown in the scope] shows the principal parts of a two roll mill.   This standard does not cover requirements for the design of an exhaust system.   This standard applies to two roll mills which are manufactured after the date of issue of this standard.

Gummi- und Kunststoffmaschinen - Walzwerke - Sicherheitsanforderungen

Diese Norm behandelt die wesentlichen Gesundheits- und Sicherheitsanforderungen an alle Walzwerke für die Aufbereitung von Kautschuk und/oder Kunststoff. Die signifikanten Gefährdungen sind in Abschnitt 4 aufgelistet und werden in dieser Norm behandelt. Die wesentlichen Teile eines Walzwerks sind in Bild 1 angegeben. Diese Norm behandelt nicht die Anforderungen an die Gestaltung einer Absaugeinrichtung. Die Norm gilt für Walzwerke, die nach dem Ausgabedatum der Norm hergestellt worden sind.

Machines pour le caoutchouc et les matieres plastiques - Mélangeurs a cylindres - Prescriptions de sécurité

Cette norme spécifie les prescriptions de prévention essentielles relatives a tous les mélangeurs a cylindres utilisés pour le travail du caoutchouc et des matieres plastiques. Les phénomenes dangereux significatifs sont énumérés a l'article 4 et sont traités dans cette norme. La figure 1 montre les principales parties d'un mélangeur a cylindres. Cette norme ne couvre pas les p prescriptions relatives a la conception d'un systeme d'aspiration. Cette norme s'applique aux mélangeurs a cylindres fabriqués apres la date de publication de cette norme.

Rubber and plastics machines - Two roll mills - Safety requirements

General Information

Status
Withdrawn
Publication Date
31-Mar-2000
Withdrawal Date
16-Sep-2008
ICS
83.200 - Equipment for the rubber and plastics industries
Technical Committee
VSN - Safety of machinery
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
10-Sep-2008
Due Date
03-Oct-2008
Completion Date
17-Sep-2008
Directive
89/392/EEC - Machinery - Safety of machinery: general essential health and safety requirements
98/37/EC - Machinery
Mandate
M/BC/CEN/88/13 - Standardization request to CEN/CENELEC relating to machinery
Ref Project
EN 1417:1996 - Rubber and plastics machines - Two roll mills - Safety requirements

Relations

Consolidated By
SIST EN 1417:2000+A1:2008 - Plastics and rubber machines - Two roll mills - Safety requirements
Effective Date
18-Jan-2023
Consolidated By
SIST EN 1417:2000+A1:2008 - Plastics and rubber machines - Two roll mills - Safety requirements
Effective Date
19-Jan-2023
Consolidated By
SIST EN 1417:2000+A1:2008 - Plastics and rubber machines - Two roll mills - Safety requirements
Effective Date
01-Nov-2008

Buy Standard

EN 1417:2000EN 1417:2000
PreviousNext
Standard
EN 1417:2000
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1417:2000
01-april-2000
Rubber and plastics machines - Two roll mills - Safety requirements
Rubber and plastics machines - Two roll mills - Safety requirements
Gummi- und Kunststoffmaschinen - Walzwerke - Sicherheitsanforderungen
Machines pour le caoutchouc et les matieres plastiques - Mélangeurs a cylindres -
Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 1417:1996
ICS:
83.200 Oprema za gumarsko Equipment for the rubber and
industrijo in industrijo plastics industries
polimernih materialov
SIST EN 1417:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1417:2000

---------------------- Page: 2 ----------------------

SIST EN 1417:2000

---------------------- Page: 3 ----------------------

SIST EN 1417:2000

---------------------- Page: 4 ----------------------

SIST EN 1417:2000

---------------------- Page: 5 ----------------------

SIST EN 1417:2000

---------------------- Page: 6 ----------------------

SIST EN 1417:2000

---------------------- Page: 7 ----------------------

SIST EN 1417:2000

---------------------- Page: 8 ----------------------

SIST EN 1417:2000

---------------------- Page: 9 ----------------------

SIST EN 1417:2000

---------------------- Page: 10 ----------------------

SIST EN 1417:2000

---------------------- Page: 11 -----------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 23582-1:2023(Main)
Plastics and rubber machines - Clamping systems - Part 1: Safety requirements for magnetic clamping systems (ISO 23582-1:2023)
EN ISO 23582-1:2023

This document specifies the essential safety requirements for the design and construction of magnetic clamping systems (MCS) for plastics and rubber machines (injection moulding machines, compression moulding machines etc.) and provides information for their safe use.
This standard deals with all significant hazards, hazardous situation or hazardous events that are listed in Annex A, when a MCS is used utilizing magnetic force to affix a mould to the plate of a machine in which is integrated, taking into consideration even conditions of misuse that are reasonably foreseeable by the manufacturer.
This standard does not cover hydraulic or pneumatic or mechanical clamping systems.
This standard is not applicable to MCS, which are manufactured before the date of its publication.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12301:2020/AC:2021(Corrigendum)
Plastics and rubber machines - Calenders - Safety requirements
EN 12301:2019/AC:2021

This document specifies safety requirements relating to the design and construction of calenders (see 3.1.1) intended for the calendering, polishing, laminating or embossing of rubber or plastics.
This document concerns the calender alone, including the following integrated components: cutting device, stock guides and feeding device, secondary roller.
Annex C shows examples of various types of calenders and Annex D shows examples of calendaring processes.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to the design and construction of calenders, when the machines are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer during all the phases of the life of the machine as described in EN ISO 12100:2010, 5.4 (see Annex B).
This document does not deal with:
-   hazards generated by the processing of explosive materials, or materials which give rise to an explosive atmosphere;
-   hazards due to laser or ionizing radiation;
-   hazards generated if the calender is installed in an explosive atmosphere.
Two roll mills are covered by EN 1417.
This document is not applicable to calenders manufactured before the date of its publication.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12012-4:2019+A1:2021(Main)
Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements for agglomerators
EN 12012-4:2019+A1:2021

This document deals with all significant hazards, hazardous situations and events relevant to agglomerators for the modification of plastic scraps in its form, size and flow characteristics, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). The hazards have been identified taking into account all phases of the machine life cycle according to EN ISO 12100:2010, 5.4.
Machines considered in this document begin at the outer edge of the feed opening and end at the outer edge of the discharge opening.
This document does not deal with:
-   hazards due to emissions by processing materials that could be hazardous to health;
-   hazards caused by ignition of flammable residues in material to be processed;
-   requirements for exhaust ventilation systems.
This document is not applicable to agglomerators manufactured before the date of its publication.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 20430:2021(Main)
Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO 20430:2020)
EN ISO 20430:2020

This standard specifies the essential safety requirements for the design, construction and use of injection moulding machines for the processing of plastics and/or rubber.

  • Standard
    161 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12301:2020(Main)
Plastics and rubber machines - Calenders - Safety requirements
EN 12301:2019

This draft European standard specifies safety requirements relating to the design and construction of calenders intended for the processing of rubber or plastics.
This draft European standard concerns the calender alone, including all components fixed to its frame.
Annex C shows examples of various types of calenders and Annex D shows examples of calendaring processes.
This draft European standard deals with all significant hazards, hazardous situations or hazardous events relevant to the design and construction of calenders, when the machines are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex B).
This draft European standard does not deal with:
-   hazards generated by the processing of explosive materials, or materials which give rise to an explosive atmosphere;
-   hazards due to laser or ionizing radiation;
-   hazards generated if the calender is installed in an explosive atmosphere.
Two roll mills are covered by EN 1417.
This draft European standard applies to machinery manufactured after its date of approval by CEN.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1612:2020(Main)
Plastics and rubber machines - Reaction moulding machines and plants - Safety requirements
EN 1612:2019

This draft European standard specifies the essential safety requirements applicable to the design and construction of reaction moulding machines and plants.
The significant and specific hazards are listed in Annex A and are dealt with in this draft European standard.
This draft European standard does not cover the hazards related to the cutting unit (see EN 14886:2008).
This draft European standard does not cover the requirements for the design of exhaust systems.
This draft European standard does not cover the hazards arising from the assembly of separate units not supplied at the same time by the same manufacturer.
This draft European standard applies to reaction moulding machines and plants manufactured after its date of publication.
Reaction moulding machines usually do not produce explosive atmospheres. Where materials are processed, which may cause an explosive atmosphere, the Directive 94/9/EC on the Equipment intended for use in Potentially Explosive Atmospheres (ATEX) should be applied. Explosion hazards are not dealt with in this document.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1114-3:2020(Main)
Plastics and rubber machines - Extruders and extrusion lines - Part 3: Safety requirements for haul-offs
EN 1114-3:2019

This draft European Standard specifies the essential safety requirements applicable to the design and construction of haul-offs for cable, cable core, profiles and pipes used in extrusion lines for processing plastic and rubber for the hazards identified in Annex A. The following kinds of haul-offs are covered:
-   caterpillar haul-offs;
-   belt haul-offs;
-   capstan haul-offs;
-   belt capstan haul-offs;
-   roller haul-offs.
The machine begins at the product inlet opening and ends at the product outlet.
Cutting units which are integrated with or attached to the haul-off are not covered.
Take-off devices used on film or sheet lines are not covered.
Unwinding and winding machines are not subject to this standard. They are being dealt with in a separate standard being produced by another working group of CEN/TC 145.
This European Standard is not applicable to haul-offs that are manufactured before the date of its publication.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12012-1:2018(Main)
Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators and shredders
EN 12012-1:2018

This European Standard specifies the essential safety requirements applicable to the design and construction of blade granulators and shredders used to reduce the size of products made from plastics and/or rubber.
Machines considered in this European Standard begin at the outer edge of the feeding device/feed opening and end at the discharge area.
This European Standard deals with all significant hazards, hazardous situations or hazardous events that are listed in Annex A, when blade granulators and shredders are used as intended and under conditions of misuse that are reasonably foreseeable by the manufacturer.
This European Standard does not deal with
-   equipment for feeding material or discharging processed material that is not an integral part of the machine,
-   hazards caused by processing materials that could be hazardous to health,
-   safety measures to reduce the risk from ignition of flammable residues in material to be processed;
-   requirements for local exhaust ventilation systems.
This European Standard is not applicable to blade granulators and shredders that are manufactured before the date of its publication.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12013:2018(Main)
Plastics and rubber machines - Internal mixers - Safety requirements
EN 12013:2018

This European Standard deals with all significant hazards, hazardous situations or hazardous events relevant to the design and construction of internal mixers for production and laboratory applications, when the machines are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A).
An internal mixer begins at the feed openings and ends at the discharge opening.
Internal mixers usually do not produce explosive atmospheres. Where materials are processed, which may cause an explosive atmosphere, the Directive 94/9/EC on the Equipment and protective systems intended for use in potentially explosive atmospheres (ATEX) should be applied. Explosion hazards are not dealt with in this document.
The safety requirements for the design of exhaust systems and of ancillary equipment are not covered. The safety requirements for the interaction between internal mixers and ancillary equipment are covered.
This European Standard is not applicable to internal mixers manufactured before the date of its publication.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16474:2015(Main)
Plastics and rubber machines - Tyre curing presses - Safety requirements
EN 16474:2015

This European Standard applies to the tyre curing presses as defined in 3.36 having the following configuration.
-  Crossing flow tyre curing presses, with two cavities with:
   -  common curing cycle and common safeguarding; or
   -  independent curing cycles and common safeguarding; or
   -  independent curing cycles and independent safeguarding.
-  Tyre curing presses with one cavity.
-  Tyre curing presses with automatic rear feeding and discharge.
The requirements and/or safety measures specified in this European Standard apply to tyre curing presses for passenger vehicle tyres and truck tyres.
Only automatic tyre loading into the mould and automatic tyre unloading from the mould are covered by this European Standard.
Feeding system and discharge system are not covered by this European Standard.
Hazard associated with falling of parts of the container or mould are not covered by this European Standard.
Safety requirements relating to the design of ancillary equipment which is not an integral part of the tyre curing press, e.g. conveying equipment are not covered in this European Standard.
Safety requirements relating the design of exhaust systems are not covered in this European Standard.
This European Standard covers the significant hazards listed in Clause 4.
NOTE   This European Standard is not intended to support the PED [1]. For pressure hazards, see informative Annex A.
This document is not applicable to tyre curing presses which are manufactured before the date of its publication as EN.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day