SIST ISO 3547-7:2008
Plain bearings - Wrapped bushes - Part 7: Measurement of wall thickness of thin-walled bushes
Plain bearings - Wrapped bushes - Part 7: Measurement of wall thickness of thin-walled bushes
This part of ISO 3547 describes, following ISO 12301, the checking methods and measuring equipment used for measuring the total wall thickness of thin-walled bushes in the finished state.
Gleitlager - Gerollte Buchsen - Teil 7: Messung der Wanddicke von dünnwandigen Lagerbuchsen
Paliers lisses - Bagues roulées - Partie 7: Mesurage de l'épaisseur de paroi des bagues minces
Drsni ležaji - Zvite puše - 7. del: Merjenje debeline stene tankostenskih puš
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 3547-7:2008
01-julij-2008
1DGRPHãþD
SIST ISO 12306:2002
Drsni ležaji - Zvite puše - 7. del: Merjenje debeline stene tankostenskih puš
Plain bearings - Wrapped bushes - Part 7: Measurement of wall thickness of thin-walled
bushes
Gleitlager - Gerollte Buchsen - Teil 7: Messung der Wanddicke von dünnwandigen
Lagerbuchsen
Paliers lisses - Bagues roulées - Partie 7: Mesurage de l'épaisseur de paroi des bagues
minces
Ta slovenski standard je istoveten z: ISO 3547-7:2007
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3547-7:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
INTERNATIONAL ISO
STANDARD 3547-7
First edition
2007-10-01
Plain bearings — Wrapped bushes —
Part 7:
Measurement of wall thickness
of thin-walled bushes
Paliers lisses — Bagues roulées —
Partie 7: Mesurage de l'épaisseur de paroi des bagues minces
Reference number
ISO 3547-7:2007(E)
©
ISO 2007
---------------------- Page: 2 ----------------------
ISO 3547-7:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 3 ----------------------
ISO 3547-7:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Symbols and units. 2
5 Purpose of checking. 2
6 Checking methods. 2
7 Requirements for measuring equipment for the contact method . 5
8 Checking of measuring equipment. 5
Bibliography . 6
© ISO 2007 – All rights reserved iii
---------------------- Page: 4 ----------------------
ISO 3547-7:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
Draft International Standards adopted by the technical committees are circulated to the member bodies for
voting. Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the
subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 3547-7 was prepared by Technical Committee ISO/TC 123, Plain bearings,
Subcommittee SC 5, Quality analysis and assurance.
This part of ISO 3547 cancels and replaces ISO 12306:1994, which has been technically revised.
ISO 3547 consists of the following parts, under the general title Plain bearings — Wrapped bushes:
⎯ Part 1: Dimensions
⎯ Part 2: Test data for outside and inside diameters
⎯ Part 3: Lubrication holes, grooves and indentations
⎯ Part 4: Materials
⎯ Part 5: Checking the outside diameter
⎯ Part 6: Checking the inside diameter
⎯ Part 7: Measurement of wall thickness of thin-wall
...
INTERNATIONAL ISO
STANDARD 3547-7
First edition
2007-10-01
Plain bearings — Wrapped bushes —
Part 7:
Measurement of wall thickness
of thin-walled bushes
Paliers lisses — Bagues roulées —
Partie 7: Mesurage de l'épaisseur de paroi des bagues minces
Reference number
ISO 3547-7:2007(E)
©
ISO 2007
---------------------- Page: 1 ----------------------
ISO 3547-7:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3547-7:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Symbols and units. 2
5 Purpose of checking. 2
6 Checking methods. 2
7 Requirements for measuring equipment for the contact method . 5
8 Checking of measuring equipment. 5
Bibliography . 6
© ISO 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 3547-7:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
Draft International Standards adopted by the technical committees are circulated to the member bodies for
voting. Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the
subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 3547-7 was prepared by Technical Committee ISO/TC 123, Plain bearings,
Subcommittee SC 5, Quality analysis and assurance.
This part of ISO 3547 cancels and replaces ISO 12306:1994, which has been technically revised.
ISO 3547 consists of the following parts, under the general title Plain bearings — Wrapped bushes:
⎯ Part 1: Dimensions
⎯ Part 2: Test data for outside and inside diameters
⎯ Part 3: Lubrication holes, grooves and indentations
⎯ Part 4: Materials
⎯ Part 5: Checking the outside diameter
⎯ Part 6: Checking the inside diameter
⎯ Part 7: Measurement of wall thickness of thin-walled bushes
iv © ISO 2007 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3547-7:2007(E)
Plain bearings — Wrapped bushes —
Part 7:
Measurement of wall thickness of thin-walled bushes
1 Scope
This part of ISO 3547 describes, following ISO 12301, the checking methods and measuring equipment used
for measuring the total wall thickness of thin-walled bushes in the finished st
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.