77.120.30 - Copper and copper alloys
ICS 77.120.30 Details
Copper and copper alloys
Kupfer und -legierungen
Cuivre et alliages de cuivre
Baker in bakrove zlitine
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 77.120.30 - Copper and copper alloys
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This European Standard specifies the composition, property requirements and tolerances on dimensions and form for seamless round drawn copper and copper alloy tubes for general purposes supplied in the size range from 3 mm up to and including 450 mm outside diameter and from 0,3 mm up to and including 20 mm wall thickness.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
NOTE Tubes having an outside diameter less than 80 mm and/or a wall thickness greater than 2 mm in certain alloys are most frequently used for free machining purposes which are specified in EN 12168.
- Standard51 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the composition, property requirements and tolerances on dimensions and form for seamless round drawn copper and copper alloy tubes for general purposes supplied in the size range from 3 mm up to and including 450 mm outside diameter and from 0,3 mm up to and including 20 mm wall thickness.
The sampling procedures and the methods of test for verification of conformity to the requirements of this document are also specified.
NOTE Tubes having an outside diameter less than 80 mm and/or a wall thickness greater than 2 mm in certain alloys are most frequently used for free machining purposes which are specified in EN 12168.
- Standard51 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for cast copper alloys for use in solid and multilayer thick-walled plain bearings. It gives a limited selection of alloys currently available for general purposes.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesEnglish languagesale 15% off
This document specifies requirements for wrought copper alloys for use in solid plain bearings, particularly for bushes. This document provides a limited selection of alloys currently available for general purposes.
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish languagesale 15% off
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for cast copper alloys for use in solid and multilayer thick-walled plain bearings. It gives a limited selection of alloys currently available for general purposes.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesEnglish languagesale 15% off
This document specifies requirements for wrought copper alloys for use in solid plain bearings, particularly for bushes. This document provides a limited selection of alloys currently available for general purposes.
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish languagesale 15% off
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
TC origin - editorial modifications to Table 8
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
TC origin - editorial modifications to Table 8
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for the estimation of the average grain size of copper and copper alloy products by ultrasound. This document can be applied for seamless round tubes as well as for flat products.
This method can be used in place of test methods according to EN ISO 2624, mentioned in the relevant product standards. As reference method and in case of doubt the intercept procedure or planimetric procedure will be used.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides a summary of material designations, compositions and the product forms in which they are available, for coppers and copper alloys standardized in European Standards by CEN/TC 133 "Copper and copper alloys".
- Technical specification64 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides a summary of material designations, compositions and the product forms in which they are available, for coppers and copper alloys standardized in European Standards by CEN/TC 133 "Copper and copper alloys".
- Technical specification64 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for the estimation of the average grain size of copper and copper alloy products by ultrasound. This document can be applied for seamless round tubes as well as for flat products.
This method can be used in place of test methods according to EN ISO 2624, mentioned in the relevant product standards. As reference method and in case of doubt the intercept procedure or planimetric procedure will be used.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the zinc content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having zinc mass fractions between 0,000 5 % and 5,0 %.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for classification of solid wires and rods for fusion welding
of copper and copper alloys. The classification of the solid wires and rods is based on their chemical
composition.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the zinc content of copper and copper alloys in the form of unwrought, wrought and cast products. The method is applicable to products having zinc mass fractions between 0,000 5 % and 6,0 %.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This draft European Standard establishes a numbering system for designation copper or copper alloys manufactured and/or used in Europe and the responsibility for the allocation and administration of numbers for individual copper materials.
The system is applicable to copper materials standardized in European Standards.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This draft European Standard establishes a numbering system for designation copper or copper alloys manufactured and/or used in Europe and the responsibility for the allocation and administration of numbers for individual copper materials.
The system is applicable to copper materials standardized in European Standards.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This standard prescribes requirements for the classification of covered electrodes for manual metal arc welding of copper and copper alloys. It includes those chemical compositions in which the copper content exceeds that of any other element.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a routine method for the analysis of copper and copper alloys by spark source optical emission spectrometry (S-OES). The method is applicable to all elements except copper commonly present in copper and copper alloys present as impurities or minor or main constituents, and detectable by S-OES.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard provides guidance on the concepts and procedures for the calibration and analysis of copper and copper alloys by wavelength dispersive X-ray fluorescence spectrometry.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the manganese content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having manganese mass fractions between 0,001 0 % and 6,0 %.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Specification specifies a molybdovanadate spectrophotometric method for the determination of phosphorus in copper and copper alloys in the form of castings or unwrought or wrought products. The method is applicable to products having phosphorus mass fractions between 0,001 % and 0,5 %.
- Technical specification13 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a routine method for the analysis of copper and copper alloys by spark source optical emission spectrometry (S-OES). The method is applicable to all elements except copper commonly present in copper and copper alloys present as impurities or minor or main constituents, and detectable by S-OES.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Specification specifies a molybdovanadate spectrophotometric method for the determination of phosphorus in copper and copper alloys in the form of castings or unwrought or wrought products. The method is applicable to products having phosphorus mass fractions between 0,001 % and 0,5 %.
- Technical specification13 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the manganese content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having manganese mass fractions between 0,001 0 % and 6,0 %.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard provides guidance on the concepts and procedures for the calibration and analysis of copper and copper alloys by wavelength dispersive X-ray fluorescence spectrometry.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies an electrolytic method for the determination of the copper content of unalloyed copper materials with a copper content higher than 99,80 % (mass fraction) in the form of castings, wrought and unwrought products. Silver, if present, is co-deposited and is reported as copper. Approximately one-half of any selenium and tellurium present will co-deposit. Bismuth, if present, also interferes.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies an electrolytic method for the determination of the copper content of unalloyed copper materials with a copper content higher than 99,80 % (mass fraction) in the form of castings, wrought and unwrought products.
Silver, if present, is co-deposited and is reported as copper. Approximately one-half of any selenium and tellurium present will co-deposit. Bismuth, if present, also interferes.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the cadmium content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having a cadmium mass fractions between 0,000 5 % and 0,1 %.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the cadmium content of copper and copper alloys in the form of unwrought, wrought and cast products. The method is applicable to products having cadmium mass fractions between 0,000 5 % and 0,1 %.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the composition, property requirements and tolerances on dimensions and form for rolled, finned, seamless copper and copper alloy tubes for heat exchangers. It gives guidelines for copper and copper alloy tubes supplied in the size range from 6 mm up to and including 35 mm outside diameter; from 1 mm up to and including 3 mm wall thickness of the unfinned section; and with fin height up to and including 1,5 mm.
The sampling procedures and the methods of testing for verification of conformity to the requirements of this European Standard are also specified.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the tin content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having medium tin mass fractions between 0,2 % and 3,0 %.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies an electrolytic method for the determination of the copper content in copper materials with a copper content less than 99,85 % (mass fraction) in the form of unwrought, wrought and cast products.
Silver, if present, is co-deposited and is reported as copper. Approximately one-half of any selenium and tellurium present will co-deposit. Arsenic, antimony, bismuth and tin, if present, also interfere.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Specification specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the tellurium content of copper and copper alloys in form of castings or unwrought or wrought products.
The method is applicable to products having tellurium mass fractions between 0,000 2 % and 0,020 %.
- Technical specification10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the tin content of copper and copper alloys in the form of unwrought, wrought and cast products.The method is applicable to products having medium tin mass fractions between 0,2 % and 3 %.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the electrolytic method for the determination of the copper content in copper materials with copper content equal to or less than 99,85 % (mass fraction) in the form of unwrought, wrought and cast products.
Silver, if present, is co-deposited and is reported as copper. Approximately one-half of any selenium and tellurium present will co-deposit. Arsenic, antimony, bismuth and tin, if present, also interfere.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This Technical Specification specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the tellurium content of copper and copper alloys in form of castings or unwrought or wrought products.
The method is applicable to products having tellurium mass fractions between 0,000 2 % and 0,020 %.
- Technical specification10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the nickel content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having a nickel mass fractions between 0,001 % and 6,0 %.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the lead in copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having lead mass fractions between 0,01 % and 5,0 %.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the tellurium content of copper and copper alloys in form of castings or unwrought or wrought products. The method is applicable to products having tellurium mass fractions between 0,20 % and 1,00 %.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies six inductively coupled plasma emission spectrometry methods (A to F) for the determination of alloying elements and impurities in copper and copper alloys in the form of unwrought, wrought and cast products. A complementary method, for the analysis of Copper-tin-lead alloys, is described in Annex B (informative). The precision criteria concerning this method do not reach the suitable level, for all the elements specified (zinc and phosphorus, namely).
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies two flame atomic absorption spectrometric methods (FAAS) for the determination of the silver content of copper and copper alloys in the form of unwrought, wrought and cast products. The methods are applicable to products having silver mass fractions between 0,01 % and 2,0 %.
a) Method A is applicable to copper and copper alloys having silver mass fractions between 0,01 % and 1,0 % and containing antimony or tin not greater than 0,005 0 % or silicon not greater than 0,010 %.
b) Method B is applicable to copper and copper alloys having silver mass fractions between 0,01 % and 2,0 % and antimony or tin greater than 0,005 % and silicon greater than 0,010 %.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of magnesium content of copper and copper alloys in the form of unwrought, wrought and cast products. The method is applicable to products having magnesium mass fractions between 0,001 % and 0,20 %.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the bismuth content of copper and copper alloys in the form of unwrought, wrought and cast products. The method is applicable to products having bismuth mass fractions between 0,01 % and 0,25 %.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the nickel content of copper and copper alloys in the form of unwrought, wrought and cast products. The method is applicable to products having a nickel mass fractions between 0,001 % and 6,0 %.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies two flame atomic absorption spectrometric methods (FAAS) for the determination of the silver content of copper and copper alloys in the form of unwrought, wrought and cast products.
The methods are applicable to products having silver mass fractions between 0,01 % and 2,0 %.
a) Method A is applicable to copper and copper alloys having silver mass fractions between 0,01 % and 1,0 % and containing antimony or tin not greater than 0,005 0 % or silicon not greater than 0,010 %.
b) Method B is applicable to copper and copper alloys having silver mass fractions between 0,01 % and 2,0 % and antimony or tin greater than 0,005 % and silicon greater than 0,010 %.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of magnesium content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having magnesium mass fractions between 0,001 % and 0,20 %.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the tellurium content of copper and copper alloys in form of castings or unwrought or wrought products.
The method is applicable to products having tellurium mass fractions between 0,20 % and 1,00 %.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies six inductively coupled plasma emission spectrometry methods (A to F) for the determination of alloying elements and impurities in copper and copper alloys in the form of unwrought, wrought and cast products.
A complementary method, for the analysis of Copper-tin-lead alloys, is described in Annex B (informative). The precision criteria concerning this method do not reach the suitable level, for all the elements specified (zinc and phosphorus, namely).
These methods are applicable to the elements listed in Tables 1 to 6 within the composition ranges shown: (...)
NOTE 1 The ranges specified for each method can be extended or adapted, for the determination of lower mass fractions.
NOTE 2 Other elements may be included. However such elements and their mass fractions should be carefully checked, taking into account interference, sensitivity, resolution and linearity criteria for each instrument and each wavelength.
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a flame atomic absorption spectrometric method (FAAS) for the determination of the bismuth content of copper and copper alloys in the form of unwrought, wrought and cast products.
The method is applicable to products having bismuth mass fractions between 0,01 % and 0,25 %.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day