SIST EN 15706:2010
(Main)Hardware for furniture - Strength and durability of slide fittings for sliding doors and roll fronts
Hardware for furniture - Strength and durability of slide fittings for sliding doors and roll fronts
This European Standard prEN 15706 specifies test methods and requirements for the strength and durability of all types of slide fittings for all types of sliding doors and roll fronts sliding horizontally and vertically and their components for all fields of application.
The tests consist of the application of loads, forces and velocities simulating normal functional use, as well as misuse, that might reasonably be expected to occur.
With the exception of the corrosion test in clause 8.4, the tests are designed to evaluate properties without regard to materials, design/construction or manufacturing processes.
The strength and durability tests only relate to the fittings and the parts used for the attachment.
The strength and durability tests are carried out in a test frame with specified properties. The test results can only be used as a guide to the performance of a piece of furniture.
The test results are only valid for the fittings tested. These results may be used to represent the performance of production models provided that the tested model is representative of the production model.
With the exception of the corrosion test in clause 8.4, ageing and influences of heat and humidity is not included.
Annex A (normative): Requirements for product information.
Annex B (normative): Loads and cycles.
Möbelbeschläge - Festigkeit und Dauerhaltbarkeit von Beschlägen für Schiebetüren und Rollläden
Dieses Dokument legt Prüfverfahren und Anforderungen für die Festigkeit und Dauerhaltbarkeit aller Arten
von Schiebebeschlägen für alle Arten von horizontal und vertikal beweglichen Schiebetüren und Rollläden
sowie deren Bauteilen für alle Anwendungsbereiche fest.
Die Prüfungen bestehen im Aufbringen von Belastungen, Kräften und Geschwindigkeiten, die den üblichen
funktionellen Gebrauch sowie einen vernünftigerweise vorhersehbaren Fehlgebrauch simulieren.
Mit Ausnahme der Korrosionsprüfung in Abschnitt 8 dienen die Prüfungen zur Bewertung von Eigenschaften
ohne Berücksichtigung von Werkstoffen, Gestaltung/Konstruktion oder Herstellverfahren.
Die Festigkeits- und Dauerhaltbarkeitsprüfungen betreffen nur die Beschläge und die für die Befestigung verwendeten
Teile.
Die Festigkeits- und Dauerhaltbarkeitsprüfungen werden in einem Prüfrahmen mit festgelegten Eigenschaften
durchgeführt. Die Prüfergebnisse können nur als Richtschnur im Hinblick auf die Funktionssicherheit eines
Möbelstücks gewertet werden.
Die Prüfergebnisse gelten nur für die geprüften Beschläge. Diese Ergebnisse können zugrunde gelegt werden,
um die Funktionssicherheit von Serienmodellen darzustellen, vorausgesetzt, das geprüfte Modell ist repräsentativ
für das Serienmodell.
Außer bei der Korrosionsprüfung in Abschnitt 8 werden die Alterung und die Einflüsse durch Wärme und
Feuchtigkeit nicht behandelt.
Anhang A (normativ): System für die Produktinformation
Anhang B (normativ): Prüfparameter
Quincaillerie d'ameublement - Résistance mécanique et endurance des éléments de coulissement pour portes coulissantes et rideaux coulissants
La présente Norme européenne EN 15706 spécifie des méthodes d’essai et des exigences relatives à la
résistance mécanique et à l’endurance de tous les types d’éléments de coulissement pour tous les types de
portes coulissantes et de rideaux coulissants à mouvement horizontal et vertical et de leurs composants
prévus pour tous les champs d’application.
Les essais consistent à appliquer des charges, forces et vitesses simulant un usage fonctionnel normal et un
mauvais usage auquel on peut raisonnablement s’attendre.
A l’exception de l’essai de corrosion décrit à l'article 8, les essais sont conçus pour évaluer les propriétés
quels que soient les matériaux, la conception/construction et les procédés de fabrication.
Les essais de résistance mécanique et d’endurance concernent uniquement les éléments de coulissement et
les parties utilisées pour leur fixation.
Les essais de résistance mécanique et d’endurance sont effectués dans une structure d’essai ayant des
propriétés spécifiées. Les résultats d’essai peuvent uniquement servir de guide en matière de performances
d’un meuble.
Les résultats d’essai ne sont valables que pour les éléments de coulissement soumis à l’essai. Ces résultats
peuvent être utilisés pour indiquer les performances des modèles fabriqués à condition que le modèle essayé
soit représentatif du modèle fabriqué.
A l’exception de l’essai de corrosion décrit à l'article 8, le vieillissement et les effets de la chaleur et de
l’humidité ne sont pas traités.
Annexe A (normative) : Système d'informations relatives au produit.
Annexe B (normative) : Paramètres d'essai.
Pohištveno okovje - Trdnost in trajnost vodil za drsna in rolo vrata
Ta evropski standard EN 15706 opredeljuje preskusne metode in zahteve za trdnost in trajnost vseh vrst vodil za drsna in rolo vrata, ki drsijo vodoravno in navpično, ter njihovih komponent na vseh področjih uporabe. Preskus je sestavljen iz vnosa obremenitev, sil in hitrosti, ki posnemajo običajno funkcionalno uporabo in upravičeno pričakovano napačno uporabo. Z izjemo korozijskega preskusa v Klavzuli 8 so preskusi zasnovani tako, da ovrednotijo lastnosti ne glede na materiale, model/konstrukcijo ali proizvodne postopke. Preskusi trdnosti in trajnosti se nanašajo le na vodila in dele, ki se uporabljajo za pritrditev. Preskusi trdnosti in trajnosti se izvajajo v preskusnem okviru z določenimi lastnostmi. Rezultati preskusa se lahko uporabijo le kot vodilo za delovanje dela pohištva. Rezultati preskusov veljajo le za preskušana vodila. Ti rezultati se lahko uporabijo za predstavitev delovanja proizvodnih modelov, če je preskusni model predstavnik proizvodnega modela. Z izjemo korozijskega preskusa v Klavzuli 8 staranje in vpliv toplote in vlage nista vključena.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Pohištveno okovje - Trdnost in trajnost vodil za drsna in rolo vrataMöbelbeschläge - Festigkeit und Dauerhaltbarkeit von Beschlägen für Schiebetüren und RolllädenQuincaillerie d'ameublement - Résistance mécanique et endurance des éléments de coulissement pour portes coulissantes et rideaux coulissantsHardware for furniture - Strength and durability of slide fittings for sliding doors and roll fronts97.140PohištvoFurnitureICS:Ta slovenski standard je istoveten z:EN 15706:2009SIST EN 15706:2010en,fr,de01-januar-2010SIST EN 15706:2010SLOVENSKI
STANDARD
SIST EN 15706:2010
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15706April 2009ICS 97.140 English VersionHardware for furniture - Strength and durability of slide fittingsfor sliding doors and roll frontsQuincaillerie d'ameublement - Résistance mécanique etendurance des éléments de coulissement pour portescoulissantes et rideaux coulissantsMöbelbeschläge - Festigkeit und Dauerhaltbarkeit vonBeschlägen für Schiebetüren und RolllädenThis European Standard was approved by CEN on 28 February 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15706:2009: ESIST EN 15706:2010
EN 15706:2009 (E) 2 Contents Page Foreword .4 Introduction .5 1 Scope .6 2 Normative references .6 3 Terms and definitions .6 4 General test conditions .7 4.1 Preliminary preparation .7 4.2 Test equipment .7 4.3 Application of forces .8 4.4 Tolerances .8 4.5 Sequence of testing .8 4.6 Inspection and assessment of results .8 5 Test apparatus .9 5.1 Masses .9 5.2 Test frame .9 5.3 Particle board . 10 5.4 Loading pad . 10 6 Test procedures and requirements for horizontal sliding doors and roll fronts . 11 6.1 General . 11 6.2 Overload test . 11 6.2.1 General . 11 6.2.2 Slam test for slide fittings with built-in end stops . 11 6.2.3 Pull-out test . 12 6.2.4 Horizontal static load test . 13 6.3 Functional tests . 13 6.3.1 General . 13 6.3.2 Operating forces . 13 6.3.3 Closing function, fittings with self-closing mechanisms . 13 6.3.4 Determination of sagging reference point (a) . 13 6.3.5 First slam shut/open . 14 6.3.6 Durability . 15 6.3.7 Second slam shut/open . 15 6.3.8 Sagging . 15 7 Test procedures and requirements for vertical sliding doors and roll fronts . 16 7.1 General . 16 7.2 Overload tests . 16 7.2.1 General . 16 7.2.2 Slam shut/open . 16 7.2.3 Horizontal static load test . 17 7.3 Functional tests . 17 7.3.1 General . 17 7.3.2 Operating forces . 17 7.3.3 First slam shut/open . 18 7.3.4 Durability . 18 7.3.5 Second slam shut/open . 18 8 Corrosion resistance . 18 9 Test report . 18 SIST EN 15706:2010
EN 15706:2009 (E) 3 Annex A (normative)
Product information system . 20 A.1 General . 20 A.2 Field of application . 20 A.3 The loading capacity and the maximum size of the sliding door/roll front . 20 A.4 Adjustment systems, built-in stops and spring and damper mechanisms . 20 A.5 Corrosion test . 20 Annex B (normative)
Test parameters . 21 Bibliography . 22
SIST EN 15706:2010
EN 15706:2009 (E) 4 Foreword This document (EN 15706:2009) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 15706:2010
EN 15706:2009 (E) 5 Introduction The aim of this draft European Standard is to provide furniture manufacturers, designers and developers with comparable information regarding the performance of all types of slide fittings and their components for sliding doors and roll fronts. SIST EN 15706:2010
EN 15706:2009 (E) 6
1 Scope This European Standard EN 15706 specifies test methods and requirements for the strength and durability of all types of slide fittings for all types of sliding doors and roll fronts sliding horizontally and vertically and their components for all fields of application. The tests consist of the application of loads, forces and velocities simulating normal functional use, as well as misuse, that might reasonably be expected to occur. With the exception of the corrosion test in Clause 8, the tests are designed to evaluate properties without regard to materials, design/construction or manufacturing processes. The strength and durability tests only relate to the fittings and the parts used for the attachment. The strength and durability tests are carried out in a test frame with specified properties. The test results can only be used as a guide to the performance of a piece of furniture. The test results are only valid for the fittings tested. These results may be used to represent the performance of production models provided that the tested model is representative of the production model. With the exception of the corrosion test in Clause 8, ageing and influences of heat and humidity are not included.
Annex A (normative): Product information system. Annex B (normative): Test parameters. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 320:1993, Fibreboards — Determination of resistance to axial withdrawal of screws EN 323:1993, Wood-based panels — Determination of density EN ISO 6270-2, Paints and varnishes — Determination of resistance to humidity — Part 2: Procedure for exposing test specimens in condensation-water atmospheres (ISO 6270-2:2005) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply.
3.1 catch device device, which keeps or pulls a sliding door/roll front in place, but does not require a second action in order to release it, e.g. a magnetic catch or a self-closing or self-opening mechanism 3.2 damper mechanism which stops the movement of a sliding door/roll front gently SIST EN 15706:2010
EN 15706:2009 (E) 7 3.3 loading capacity M mass in kg, as specified by the manufacturer, for which the slide fitting will fulfil the strength and durability requirements. The loading capacity includes the weight of the sliding door/roll front and load on it, e.g. mirrors 3.4 horizontal sliding door one or more front elements, which can be moved in the horizontal direction 3.5 vertical sliding door one or more front elements, which can be moved in the vertical direction 3.6 horizontal roll front front element usually consisting of many narrow parts, which can be moved in the horizontal direction 3.7 vertical roll front front element usually consisting of many narrow parts, which can be moved in the vertical direction 4 General test conditions 4.1 Preliminary preparation The fittings shall be assembled/mounted according to the manufacturer’s instructions supplied with the product.
If mounting, adjustment or assembly instructions are not supplied, the most adverse configuration shall be used and the mounting or assembly method shall be recorded in the test report. Fittings shall be tightened before testing and shall not be re-tightened unless specifically required in the manufacturer’s instructions. If the configuration must be changed to produce the worst-case conditions, this shall be recorded in the test report. The tests shall be carried out in indoor ambient conditions at a temperature between 15 °C and 25 °C. If during a test the temperature is outside of the range of 15 °C to 25 °C, the maximum and/or minimum temperature shall be recorded in the test report.
Fittings which include structural hardware parts made of hygroscopic plastic materials, e.g. polyamide shall be conditioned at (23 ± 5) °C and a relative humidity of (50 ± 5) % for at least 7 days before testing.
In the case of designs not addressed in the test procedures, the tests shall be carried out as far as possible as described, and deviations from the test procedure recorded in the test report. Before beginning the testing, visually inspect the fittings and components thoroughly. Record any defects so that they are not assumed to have been caused by the tests. Carry out measurements if specified. 4.2 Test equipment Unless otherwise specified, the tests may be applied by any suitable device, because results are not dependent upon the apparatus. The equipment shall not inhibit deflection of the test door/roll front, i.e. it shall be able to move so that it will allow the deflection of the test sliding door/roll front during testing. SIST EN 15706:2010
EN 15706:2009 (E) 8 All loading pads (if included) shall be capable of pivoting in relation to the direction of the applied force. The pivot point shall be as close as practically possible to the load surface. 4.3 Application of forces The forces in the static load tests shall be applied sufficiently slowly to ensure that negligible dynamic force is applied. Unless otherwise specified, each force shall be maintained for not less than 10 s and not more than 15 s. The forces in durability tests shall be applied at a rate to ensure that excessive heating does not occur. The forces may be replaced by masses. The relation 10 N = 1 kg shall be used for this purpose. 4.4 Tolerances Unless otherwise stated, the following tolerances are applicable: Forces:
± 5 % of the nominal force; Velocities: ± 5 % of the nominal velocity; Masses:
± 1 % of the nominal mass; Dimensions: ± 1 mm of the nominal dimension; Angle
± 2° of nominal angle. The accuracy for the positioning of loading pads shall be ± 5 mm. 4.5 Sequence of testing The tests shall be carried out in the same sequence as the clauses are numbered in this standard. If the clause sequence is not followed, the sequence shall be recorded in the test report.
4.6 Inspection and assessment of results Before and after completion of each test, carry out the inspection as specified, after removing any loads and after using adjustment devices, if applicable. Record any changes that have taken place since the initial inspection.
The inspection shall include at least the following: a) fracture of any component or joint; b) loosening of any joint intended to be rigid, which can be demonstrated by hand pressure; c) deformation or wear of any part or component such that its functioning is impaired; d) loosening of any means of fixing components; e) any impaired function of a component or part.
SIST EN 15706:2010
EN 15706:2009 (E) 9 5 Test apparatus 5.1 Masses Masses shall b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.