SIST EN ISO 24266:2021
(Main)Footwear - Test methods for whole shoe - flexing durability (ISO 24266:2020)
Footwear - Test methods for whole shoe - flexing durability (ISO 24266:2020)
This International Standard specifies two test methods for the determination of the flexing durability of whole shoes. The two methods may not give comparable results.
These methods are not applicable to the whole shoes with heel height more than 70 mm, or the thickness of flexing area of the soles more than 25 mm, or flexing angle less than 45° according to ISO 17707:2005 clause 6 rigidity test.
Schuhe - Prüfverfahren für den ganzen Schuh - Biegebeständigkeit (ISO 24266:2020)
Dieses Dokument legt zwei Prüfverfahren zur Bestimmung der Biegebeständigkeit von ganzen Schuhen fest. Die beiden Verfahren liefern unter Umständen keine vergleichbaren Ergebnisse.
ANMERKUNG Das gewählte Prüfverfahren hängt von der Vereinbarung zwischen den Beteiligten ab, die dieses Prüfverfahren oder auf dieses Prüfverfahren verweisende Produktnormen anwenden.
Diese Verfahren sind nicht für ganze Schuhe mit Absätzen höher als 50 mm oder Dicken der Biegeflächen der Sohlen von mehr als 25 mm oder Biegewinkeln von unter 45° entsprechend ISO 17707:2005, Abschnitt 6 anzuwenden.
Chaussures - Méthodes d'essai pour toute la chaussure - Durabilité vis-à-vis de la flexion (ISO 24266:2020)
Le présent document spécifie deux méthodes d'essai pour la détermination de la durabilité vis-à-vis de la flexion de chaussures entières. Ces deux méthodes peuvent ne pas donner de résultats comparables.
NOTE La méthode d'essai choisie dépend de l'accord passé entre les parties concernées qui utilisent cette méthode d'essai ou des normes de produits qui y font référence.
Ces méthodes ne sont pas applicables aux chaussures entières dont la hauteur de talon est supérieure à 50 mm, dont l'épaisseur de la zone de flexion des semelles est supérieure à 25 mm ou dont l'angle de flexion est inférieur à 45° conformément à l'Article 6 de l'ISO 17707:2005.
Obutev - Preskusne metode za celoten čevelj - Vzdržljivost upogiba (ISO 24266:2020)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24266:2021
01-januar-2021
Obutev - Preskusne metode za celoten čevelj - Vzdržljivost upogiba (ISO
24266:2020)
Footwear - Test methods for whole shoe - flexing durability (ISO 24266:2020)
Schuhe - Prüfverfahren für den ganzen Schuh - Biegebeständigkeit (ISO 24266:2020)
Chaussures - Méthodes d'essai pour toute la chaussure - Durabilité vis-à-vis de la flexion
(ISO 24266:2020)
Ta slovenski standard je istoveten z: EN ISO 24266:2020
ICS:
61.060 Obuvala Footwear
SIST EN ISO 24266:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24266:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 24266:2021
EN ISO 24266
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2020
EUROPÄISCHE NORM
ICS 61.060
English Version
Footwear - Test methods for whole shoe - Flexing
durability (ISO 24266:2020)
Chaussures - Méthodes d'essai pour toute la chaussure Schuhe - Prüfverfahren für den ganzen Schuh -
- Durabilité vis-à-vis de la flexion (ISO 24266:2020) Biegebeständigkeit (ISO 24266:2020)
This European Standard was approved by CEN on 20 September 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24266:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24266:2021
EN ISO 24266:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24266:2021
EN ISO 24266:2020 (E)
European foreword
This document (EN ISO 24266:2020) has been prepared by Technical Committee ISO/TC 216
"Footwear" in collaboration with Technical Committee CEN/TC 309 “Footwear” the secretariat of which
is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2021, and conflicting national standards shall be
withdrawn at the latest by May 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 24266:2020 has been approved by CEN as EN ISO 24266:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24266:2021
---------------------- Page: 6 ----------------------
SIST EN ISO 24266:2021
INTERNATIONAL ISO
STANDARD 24266
First edition
2020-11
Footwear — Test methods for whole
shoe — Flexing durability
Chaussures — Méthodes d'essai pour toute la chaussure — Durabilité
vis-à-vis de la flexion
Reference number
ISO 24266:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 24266:2021
ISO 24266:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24266:2021
ISO 24266:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
5.1 Method A . 2
5.2 Method B . 3
6 Sampling and conditioning . 5
7 Test method . 6
7.1 Method A . 6
7.2 Method B . 8
8 Test result . 9
9 Test report . 9
Bibliography .11
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 24266:2021
ISO 24266:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 216, Footwear, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 309, Footwear, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
-
...
SLOVENSKI STANDARD
oSIST prEN ISO 24266:2020
01-januar-2020
Obutev - Preskusne metode za celoten čevelj - Vzdržljivost upogiba (ISO/DIS
24266:2019)
Footwear - Test methods for whole shoe - flexing durability (ISO/DIS 24266:2019)
Schuhe - Prüfverfahren für den ganzen Schuh - Biegebeständigkeit (ISO/DIS
24266:2019)
Chaussures - Méthodes d'essai pour toute la chaussure - Durabilité vis-à-vis de la flexion
(ISO/DIS 24266:2019)
Ta slovenski standard je istoveten z: prEN ISO 24266
ICS:
61.060 Obuvala Footwear
oSIST prEN ISO 24266:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 24266:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 24266:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24266
ISO/TC 216 Secretariat: UNE
Voting begins on: Voting terminates on:
2019-10-21 2020-01-13
Footwear — Test methods for whole shoe — Flexing
durability
ICS: 61.060
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24266:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 24266:2020
ISO/DIS 24266:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 24266:2020
ISO/DIS 24266:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
4.1 Method A . 1
4.1.1 Flexing machine . 1
4.1.2 Vernier caliper . 2
4.2 Method B . 2
4.2.1 Flexing machine . 2
4.2.2 Flexing last . 3
4.2.3 Vernier callipers . 4
4.2.4 Cutting tool . 4
5 Sampling and conditioning . 5
6 Test method . 5
6.1 Method A . 5
6.2 Method B . 6
7 Test result . 7
8 Test report . 7
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 24266:2020
ISO/DIS 24266:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 216, Footwear.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 24266:2020
DRAFT INTERNATIONAL STANDARD ISO/DIS 24266:2019(E)
Footwear — Test methods for whole shoe — Flexing
durability
1 Scope
This International Standard specifies two test methods for the determination of the flexing durability
of whole shoes. The two methods may not give comparable results.
These methods are not applicable to the whole shoes with heel height more than 70 mm, or the thicknes
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.