SIST EN ISO 19410-1:2023
(Main)Footwear sizing - Inshoe measurement - Part 1: Shoe length (ISO 19410-1:2022)
Footwear sizing - Inshoe measurement - Part 1: Shoe length (ISO 19410-1:2022)
This standard specifies a method to measure the effective shoe length to accommodate the foot. This standard is not applicable to heel open shoes.
Schuhgrößenbestimmung - Messung des Innenschuhs - Teil 1: Schuhlänge (ISO 19410-1:2022)
Dieses Dokument legt ein Verfahren zur Messung der effektiven Schuhlänge zur Aufnahme des Fußes fest.
Dieses Dokument ist nicht anwendbar für Schuhe, bei denen Ferse und Zehen freiliegen (Beispiel: Sandalen).
Pointures des chaussures - Mesurage interne - Partie 1: Longueur de la chaussure (ISO 19410-1:2022)
Le présent document spécifie une méthode de mesure de la longueur chaussante adaptée au pied.
Il n’est pas applicable aux chaussures à bout et talon ouverts (par exemple, les sandales).
Določanje velikosti obutve - Merjenje notranjosti čevlja - 1. del: Dolžina čevlja (ISO 19410-1:2022)
Ta standard določa metodo za merjenje dejanske dolžine čevlja za prilagoditev stopalu. Ta standard se ne uporablja za čevlje z odprto peto.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19410-1:2023
01-januar-2023
Določanje velikosti obutve - Merjenje notranjosti čevlja - 1. del: Dolžina čevlja (ISO
19410-1:2022)
Footwear sizing - Inshoe measurement - Part 1: Shoe length (ISO 19410-1:2022)
Schuhgrößenbestimmung - Messung des Innenschuhs - Teil 1: Schuhlänge (ISO 19410-
1:2022)
Pointures des chaussures - Mesurage interne - Partie 1: Longueur de la chaussure (ISO
19410-1:2022)
Ta slovenski standard je istoveten z: EN ISO 19410-1:2022
ICS:
61.060 Obuvala Footwear
SIST EN ISO 19410-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 19410-1:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 19410-1:2023
EN ISO 19410-1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 61.060
English Version
Footwear sizing - Inshoe measurement - Part 1: Shoe
length (ISO 19410-1:2022)
Pointures des chaussures - Mesurage interne - Partie 1: Schuhgrößenbestimmung - Messung des Innenschuhs -
Longueur de la chaussure (ISO 19410-1:2022) Teil 1: Schuhlänge (ISO 19410-1:2022)
This European Standard was approved by CEN on 11 November 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19410-1:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19410-1:2023
EN ISO 19410-1:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 19410-1:2023
EN ISO 19410-1:2022 (E)
European foreword
This document (EN ISO 19410-1:2022) has been prepared by Technical Committee ISO/TC 137
"Footwear sizing designations and marking systems" in collaboration with Technical Committee
CEN/TC 309 “Footwear” the secretariat of which is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 19410-1:2022 has been approved by CEN as EN ISO 19410-1:2022 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 19410-1:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 19410-1:2023
INTERNATIONAL ISO
STANDARD 19410-1
First edition
2022-10
Footwear sizing — In-shoe
measurement —
Part 1:
Shoe length
Pointures des chaussures — Mesurage interne —
Partie 1: Longueur de la chaussure
Reference number
ISO 19410-1:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 19410-1:2023
ISO 19410-1:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 19410-1:2023
ISO 19410-1:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Sampling . 4
7 Procedure .5
8 Result of measurement .6
9 Test report . 6
iii
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 19410-1:2023
ISO 19410-1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any
...
SLOVENSKI STANDARD
oSIST prEN ISO 19410-1:2022
01-februar-2022
Določanje velikosti obutve - Merjenje notranjosti čevlja - 1. del: Dolžina čevlja
(ISO/DIS 19410-1:2021)
Footwear sizing - Inshoe measurement - Part 1: Shoe length (ISO/DIS 19410-1:2021)
Schuhgrößenbestimmung - Messung des Innenschuhs - Teil 1: Schuhlänge (ISO/DIS
19410-1:2021)
Chaussures - Pointures - Partie 1: Mesurage interne des chaussures (ISO/DIS 19410-
1:2021)
Ta slovenski standard je istoveten z: prEN ISO 19410-1
ICS:
61.060 Obuvala Footwear
oSIST prEN ISO 19410-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 19410-1:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 19410-1:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19410-1
ISO/TC 137 Secretariat: SABS
Voting begins on: Voting terminates on:
2021-12-07 2022-03-01
Footwear sizing — In-shoe measurement —
Part 1:
Shoe length
ICS: 61.060
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19410-1:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2021
---------------------- Page: 3 ----------------------
oSIST prEN ISO 19410-1:2022
ISO/DIS 19410-1:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 19410-1:2022
ISO/DIS 19410-1:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
5.1 Length measurement . 1
5.1.1 Toe height sensor . 3
5.1.2 Heel back curve sensor . 4
5.2 Ruler (in mm) . 4
6 Sampling . 5
7 Procedure .5
8 Result of measurement .6
9 Test report . 6
iii
© ISO 2021 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 19410-1:2022
ISO/DIS 19410-1:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO's adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
This document was prepared by Technical Committee ISO/TC 137, Footwear sizing designations and
marking systems
iv
© ISO 2021 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 19410-1:2022
ISO/DIS 19410-1:2021(E)
Introduction
The International Organization for Standardization (ISO) draw attention to the fact that it is claimed
that compliance with this document may involve the use of a patent.
ISO takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has assured ISO that he/she is willing to negotiate licences under
reasonable and non-discriminatory terms and conditions with applicants throughout the world. In
this respect, the statement of the holder of this patent right is registered with ISO
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.