EN ISO 24266:2020

Footwear - Test methods for whole shoe - Flexing durability (ISO 24266:2020)

This document specifies two test methods for the determination of the flexing durability of whole shoes. The two methods might not give comparable results.
NOTE     The selected test method depends on agreement between relative parties who use this test method or product standards which reference this test method.
These methods are not applicable to the whole shoes with heel height more than 50 mm, or the thickness of flexing area of the soles more than 25 mm, or flexing angle less than 45° according to ISO 17707:2005, Clause 6.

Schuhe - Prüfverfahren für den ganzen Schuh - Biegebeständigkeit (ISO 24266:2020)

Dieses Dokument legt zwei Prüfverfahren zur Bestimmung der Biegebeständigkeit von ganzen Schuhen fest. Die beiden Verfahren liefern unter Umständen keine vergleichbaren Ergebnisse.
ANMERKUNG Das gewählte Prüfverfahren hängt von der Vereinbarung zwischen den Beteiligten ab, die dieses Prüfverfahren oder auf dieses Prüfverfahren verweisende Produktnormen anwenden.
Diese Verfahren sind nicht für ganze Schuhe mit Absätzen höher als 50 mm oder Dicken der Biegeflächen der Sohlen von mehr als 25 mm oder Biegewinkeln von unter 45° entsprechend ISO 17707:2005, Abschnitt 6 anzuwenden.

Chaussures - Méthodes d'essai pour toute la chaussure - Durabilité vis-à-vis de la flexion (ISO 24266:2020)

Le présent document spécifie deux méthodes d'essai pour la détermination de la durabilité vis-à-vis de la flexion de chaussures entières. Ces deux méthodes peuvent ne pas donner de résultats comparables.
NOTE       La méthode d'essai choisie dépend de l'accord passé entre les parties concernées qui utilisent cette méthode d'essai ou des normes de produits qui y font référence.
Ces méthodes ne sont pas applicables aux chaussures entières dont la hauteur de talon est supérieure à 50 mm, dont l'épaisseur de la zone de flexion des semelles est supérieure à 25 mm ou dont l'angle de flexion est inférieur à 45° conformément à l'Article 6 de l'ISO 17707:2005.

Obutev - Preskusne metode za celoten čevelj - Vzdržljivost upogiba (ISO 24266:2020)

General Information

• Status: Published
• Publication Date: 17-Nov-2020
• Withdrawal Date: 30-May-2021
• ICS: 61.060 - Footwear
• Technical Committee: CEN/TC 309 - Footwear
• Drafting Committee: CEN/TC 309/WG 1 - Minimum performance requirements and test methods for components for footwear
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 18-Nov-2020
• Completion Date: 18-Nov-2020
• Ref Project: SIST EN ISO 24266:2021 - Footwear - Test methods for whole shoe - flexing durability (ISO 24266:2020)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 24266:2021
01-januar-2021
Obutev - Preskusne metode za celoten čevelj - Vzdržljivost upogiba (ISO
24266:2020)
Footwear - Test methods for whole shoe - flexing durability (ISO 24266:2020)
Schuhe - Prüfverfahren für den ganzen Schuh - Biegebeständigkeit (ISO 24266:2020)
Chaussures - Méthodes d'essai pour toute la chaussure - Durabilité vis-à-vis de la flexion
(ISO 24266:2020)
Ta slovenski standard je istoveten z: EN ISO 24266:2020
ICS:
61.060 Obuvala Footwear
SIST EN ISO 24266:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 24266:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 24266:2021


EN ISO 24266
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2020
EUROPÄISCHE NORM
ICS 61.060
English Version

Footwear - Test methods for whole shoe - Flexing
durability (ISO 24266:2020)
Chaussures - Méthodes d'essai pour toute la chaussure Schuhe - Prüfverfahren für den ganzen Schuh -
- Durabilité vis-à-vis de la flexion (ISO 24266:2020) Biegebeständigkeit (ISO 24266:2020)
This European Standard was approved by CEN on 20 September 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24266:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 24266:2021
EN ISO 24266:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 24266:2021
EN ISO 24266:2020 (E)
European foreword
This document (EN ISO 24266:2020) has been prepared by Technical Committee ISO/TC 216
"Footwear" in collaboration with Technical Committee CEN/TC 309 “Footwear” the secretariat of which
is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2021, and conflicting national standards shall be
withdrawn at the latest by May 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 24266:2020 has been approved by CEN as EN ISO 24266:2020 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 24266:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 24266:2021
INTERNATIONAL ISO
STANDARD 24266
First edition
2020-11
Footwear — Test methods for whole
shoe — Flexing durability
Chaussures — Méthodes d'essai pour toute la chaussure — Durabilité
vis-à-vis de la flexion
Reference number
ISO 24266:2020(E)
©
ISO 2020

---------------------- Page: 7 ----------------------
SIST EN ISO 24266:2021
ISO 24266:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or
...