SIST ISO 10228:2012

Cross-country skis -- Binding mounting area -- Requirements for test screws

ISO 10228:2011 specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of cross-country skis.

Skis de fond -- Zone de montage de la fixation -- Exigences pour les vis d'essai

L'ISO 10228:2011 spécifie les dimensions, les propriétés mécaniques et les caractéristiques de tenue des vis d'essai utilisées lors de l'essai réalisé sur Ia zone de montage de la fixation des skis de fond.

Tekaške smuči - Območje montaže varnostnih vezi - Zahteve za preskusne vijake

Ta mednarodni standard določa dimenzije, mehanske lastnosti in lastnosti pritrjevanja preskusnih vijakov za preskušanje območja montaže varnostnih vezi pri tekaških smučeh.

General Information

• Status: Published
• Public Enquiry End Date: 19-Dec-2011
• Publication Date: 24-Jan-2012
• ICS: 97.220.20 - Winter sports equipment
• Technical Committee: SPO - Sports
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 12-Jan-2012
• Due Date: 18-Mar-2012
• Completion Date: 25-Jan-2012
• Ref Project: ISO 10228:2011 - Cross-country skis - Binding mounting area - Requirements for test screws

Relations

• Replaces: SIST ISO 10228:1995 - Cross-country skis -- Binding mounting area -- Requirements for test screws
• Effective Date: 01-Mar-2012

Overview

SIST ISO 10228:2012 is an international standard specifying the requirements for test screws used in measuring the binding mounting area of cross-country skis. Published by the International Organization for Standardization (ISO), this standard defines the dimensions, mechanical properties, and fastening characteristics essential for test screws to ensure consistency and reliability in binding area evaluations.

By standardizing test screws, SIST ISO 10228:2012 enables manufacturers and testing institutions worldwide to obtain comparable measurement data during binding mounting tests, supporting product quality, safety, and performance consistency in cross-country ski equipment.

Key Topics

• Scope and Application
  SIST ISO 10228:2012 applies exclusively to test screws used to assess binding mounting areas on cross-country skis, focusing on ensuring standardized test conditions.

• Design and Dimensions

  • Test screws must feature a cross recess type Z No. 3 screw head with specified penetration depths.
  • The nominal diameters and lengths (e.g., 6.3 mm × 18 mm) are clearly designated.
  • Thread length and end configurations are precisely defined to maintain test uniformity.

• Mechanical and Material Requirements

  • Test screws are made from heat-treated steel according to ISO 2702, with additional strength and durability criteria specific to ski-binding testing.
  • They must resist a breaking torque of at least 10 N·m and show high ductility under test conditions.

• Surface Treatment

  • Protective coatings such as zinc electroplating with chromate conversion ensure corrosion resistance and consistent friction during tests.
  • Adequate measures to prevent hydrogen embrittlement during plating are mandated.

• Fastening Characteristics

  • The fastening strength and pull-out resistance must meet or exceed references set by related screw standards (e.g., ISO 1478).
  • Uniform pilot hole diameter guidance ensures comparable screw engagement and test reproducibility.

Applications

SIST ISO 10228:2012 test screws are vital components within the cross-country skiing equipment manufacturing and testing sectors. Their practical applications include:

• Quality Assurance
  Manufacturers use standardized test screws to verify the structural integrity and mounting precision of ski bindings, fostering safer and more reliable ski designs.

• Research and Development
  Ski designers and engineers employ these screws to simulate real mounting conditions during prototype testing, ensuring optimal binding placement.

• Certification and Compliance Testing
  Testing bodies and certification organizations rely on this standard to confirm that products meet international safety and performance benchmarks.

• Standardized Data Collection
  Ensures that measurements related to binding mounting areas are consistent across labs and manufacturers, facilitating fair comparisons and improvements.

Related Standards

SIST ISO 10228:2012 references and aligns with several ISO standards essential for comprehensive test screw specification and ski binding testing:

• ISO 1478 - Tapping screws thread specification.
• ISO 2702 - Mechanical properties of heat-treated steel tapping screws.
• ISO 7794 - Requirements for ski-binding screws on cross-country skis.
• ISO 7795 - Test methods for ski-binding screws.
• ISO 4757 - Cross recess specifications for screws.
• ISO 4042 - Fasteners - Electroplated coatings.

These related standards collectively support the manufacturing, testing, and quality control processes in snowsport equipment production.

---

Keywords: ISO 10228, test screws, cross-country skis, binding mounting area, screw specifications, ski-binding testing, mechanical properties, fastening characteristics, ski equipment standards, corrosion-resistant coatings, standardized testing screws.

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Skis de fond -- Zone de montage de la fixation -- Exigences pour les vis d'essaiCross-country skis -- Binding mounting area -- Requirements for test screws97.220.20Oprema za zimske športeWinter sports equipmentICS:Ta slovenski standard je istoveten z:ISO 10228:2011oSIST ISO 10228:2011en01-december-2011oSIST ISO 10228:2011SLOVENSKI
STANDARD
oSIST ISO 10228:2011
Reference numberISO 10228:2011(E)© ISO 2011
INTERNATIONAL STANDARD ISO10228Second edition2011-05-15Cross-country skis — Binding mounting area — Requirements for test screws Skis de fond — Zone de montage de la fixation — Exigences pour les vis d'essai
oSIST ISO 10228:2011
©
ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii © ISO 2011 – All rights reserved
oSIST ISO 10228:2011
oSIST ISO 10228:2011
oSIST ISO 10228:2011
INTERNATIONAL STANDARD ISO 10228:2011(E) © ISO 2011 – All rights reserved 1 Cross-country skis — Binding mounting area — Requirements for test screws 1 Scope This International Standard specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of cross-country skis. 2 Normative references The following referenced documents are indispensable for the application of thi
...

SLOVENSKI STANDARD
01-marec-2012
1DGRPHãþD
SIST ISO 10228:1995
7HNDãNHVPXþL2EPRþMHPRQWDåHYDUQRVWQLKYH]L=DKWHYH]DSUHVNXVQHYLMDNH
Cross-country skis -- Binding mounting area -- Requirements for test screws
Skis de fond -- Zone de montage de la fixation -- Exigences pour les vis d'essai
Ta slovenski standard je istoveten z: ISO 10228:2011
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 10228
Second edition
2011-05-15
Cross-country skis — Binding mounting
area — Requirements for test screws
Skis de fond — Zone de montage de la fixation — Exigences pour les
vis d'essai
Reference number
©
ISO 2011
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10228 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment,
Subcommittee SC 4, Snowsports equipment.
This second edition cancels and replaces the first edition (ISO 10228:1991), which has been technically
revised.
Introduction
The use of test screws ensures the comparability of measurement data, which are determined by the
manufacturer or other institutions by testing the binding mounting area of cross-country skis.

iv © ISO 2011 – All rights reserved

INTERNATIONAL STANDARD ISO 10228:2011(E)

Cross-country skis — Binding mounting area — Requirements
for test screws
1 Scope
This International Standard specifies the dimensions, mechanical properties and fastening characteristics of
test screws used for testing the binding mounting area of cross-country skis.
...

INTERNATIONAL ISO
STANDARD 10228
Second edition
2011-05-15
Cross-country skis — Binding mounting
area — Requirements for test screws
Skis de fond — Zone de montage de la fixation — Exigences pour les
vis d'essai
Reference number
©
ISO 2011
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10228 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment,
Subcommittee SC 4, Snowsports equipment.
This second edition cancels and replaces the first edition (ISO 10228:1991), which has been technically
revised.
Introduction
The use of test screws ensures the comparability of measurement data, which are determined by the
manufacturer or other institutions by testing the binding mounting area of cross-country skis.

iv © ISO 2011 – All rights reserved

INTERNATIONAL STANDARD ISO 10228:2011(E)

Cross-country skis — Binding mounting area — Requirements
for test screws
1 Scope
This International Standard specifies the dimensions, mechanical properties and fastening characteristics of
test screws used for testing the binding mounting area of cross-country skis.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1478, Tapping screws thread
ISO 2702, Heat-treated steel tapping screws — Mechanical properties
ISO 7794, Cross-country skis — Ski-binding screws — Requirements
ISO 7
...

NORME ISO
INTERNATIONALE 10228
Deuxième édition
2011-05-15
Skis de fond — Zone de montage de la
fixation — Exigences pour les vis d'essai
Cross-country skis — Binding mounting area — Requirements for test
screws
Numéro de référence
©
ISO 2011
DOCUMENT PROTÉGÉ PAR COPYRIGHT

©  ISO 2011
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Publié en Suisse
ii © ISO 2011 – Tous droits réservés

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 10228 a été élaborée par le comité technique ISO/TC 83, Matériel de sports et d'activités de plein air,
sous-comité SC 4, Équipements de sport de neige.
Cette deuxième édition annule et remplace la première édition (ISO 10228:1991), qui a fait l'objet d'une
révision technique.
Introduction
L'utilisation de vis d'essai permet de comparer les données de mesure qui sont déterminées par le fabricant
ou par tout autre organisme lors de l'essai réalisé sur la zone de montage de la fixation des skis de fond.

iv © ISO 2011 – Tous droits réservés

NORME INTERNATIONALE ISO 10228:2011(F)

Skis de fond — Zone de montage de la fixation — Exigences
pour les vis d'essai
1 Domaine d'application
La présente Norme internationale spécifie les dimensions, les propriétés mécaniques et les caractéristiques
de tenue des vis d'essai utilisées lors de l'essai réalisé sur Ia zone de montage de la fixation des skis de fond.
2 Références normatives
Les documents de référence suivants sont indispensables à l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 1478, Filetage de vis à tôle
ISO 2702, Vis à tôle en acier traité thermiquement ― Caractéristiques mécaniques
ISO 7794, Skis de fond ― Vis de fixation ― Exigences
ISO 7795, Skis de fond ― Vis de fixation ― Méthode
...