SIST EN ISO 284:2013
(Main)Conveyor belts - Electrical conductivity - Specification and test method (ISO 284:2012)
Conveyor belts - Electrical conductivity - Specification and test method (ISO 284:2012)
This International Standard specifies the maximum electrical resistance of a conveyor belt and the corresponding test method. The test is intended to ensure that the belt is sufficiently conductive to avoid the accumulation of electrical static charge which can be developed during service use. This International Standard is not suitable or applicable to light conveyor belts as described in ISO 21183-1, the static electrical properties of which are measured by ISO 21178.
Fördergurte - Elektrische Leitfähigkeit - Spezifikation und Prüfverfahren (ISO 284:2012)
Diese Internationale Norm legt den größten elektrischen Widerstand eines Fördergurtes und das entsprechende Prüfverfahren fest.
Mit der Prüfung soll sichergestellt werden, dass der Gurt genügend leitfähig ist, um eine Erhöhung elektrostatischer Aufladungen zu verhindern, die während des Betriebes entstehen können.
Diese Internationale Norm ist nicht geeignet oder anwendbar für leichte Fördergurte, die in ISO 21883 1 [1] beschrieben sind. Deren elektrische Eigenschaften werden nach ISO 21178 [2] gemessen.
Courroies transporteuses - Conductibilité électrique - Spécification et méthode d'essai (ISO 284:2012)
L'ISO 284:2012 spécifie la résistance électrique maximale que doit présenter une courroie transporteuse, ainsi que la méthode d'essai correspondante.
Cet essai a pour objectif de s'assurer que la courroie est suffisamment conductrice afin d'éviter l'accumulation des charges d'électricité statique qui pourraient s'y former en service.
L'ISO 284:2012 n'est pas appropriée ou applicable pour les courroies transporteuses légères décrites dans l'ISO 21183‑1, dont les propriétés d'électricité statique sont mesurées par l'ISO 21178.
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Električna prevodnost - Specifikacija in preskusna metoda (ISO 284:2012)
Ta mednarodni standard določa največjo električno upornost trakov tračnih transporterjev in ustrezno preskusno metodo. Preskus je namenjen zagotavljanju zadostne prevodnosti traku, da se prepreči akumulacija električnega statičnega naboja, ki lahko nastane med uporabo. Ta mednarodni standard ni primeren ali uporaben za lahke trakove tračnih transporterjev, ki so opisani v standardu ISO 21183-1; njihove statične električne lastnosti se merijo z uporabo standarda ISO 21178.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 284:2013
01-junij-2013
1DGRPHãþD
SIST EN ISO 284:2004
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY(OHNWULþQD
SUHYRGQRVW6SHFLILNDFLMDLQSUHVNXVQDPHWRGD ,62
Conveyor belts - Electrical conductivity - Specification and test method (ISO 284:2012)
Fördergurte - Elektrische Leitfähigkeit - Spezifikation und Prüfverfahren (ISO 284:2012)
Courroies transporteuses - Conductibilité électrique - Spécification et méthode d'essai
(ISO 284:2012)
Ta slovenski standard je istoveten z: EN ISO 284:2012
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 284:2013 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 284:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 284:2013
EUROPEAN STANDARD
EN ISO 284
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 53.040.10 Supersedes EN ISO 284:2003
English Version
Conveyor belts - Electrical conductivity - Specification and test
method (ISO 284:2012)
Courroies transporteuses - Conductibilité électrique - Fördergurte - Elektrische Leitfähigkeit - Spezifikation und
Spécification et méthode d'essai (ISO 284:2012) Prüfverfahren (ISO 284:2012)
This European Standard was approved by CEN on 30 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 284:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 284:2013
EN ISO 284:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 284:2013
EN ISO 284:2012 (E)
Foreword
This document (EN ISO 284:2012) has been prepared by Technical Committee ISO/TC 41 "Pulleys and belts
(including veebelts)" in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the secretariat
of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 284:2003.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 284:2012 has been approved by CEN as a EN ISO 284:2012 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 284:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 284:2013
INTERNATIONAL ISO
STANDARD 284
Fourth edition
2012-12-01
Conveyor belts — Electrical conductivity —
Specification and test method
Courroies transporteuses — Conductibilité électrique — Spécification et
méthode d’essai
Reference number
ISO 284:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 284:2013
ISO 284:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 284:2013
ISO 284:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Specification . 1
4 Test method . 1
4.1 Principle . 1
4.2 Materials and apparatus . 1
4.3 Test pieces . 2
4.4 Atmosphere for conditioning and testing . 3
4.5 Procedure . 3
4.6 Expression of results . 4
4.7 Test report . 4
Annex A (informative) Variation of electrical resistance with temperature and humidity . 5
Bibliography . 6
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 284:2013
ISO 284:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft Internatio
...
SLOVENSKI STANDARD
kSIST FprEN ISO 284:2012
01-oktober-2012
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHMHY(OHNWULþQD
SUHYRGQRVW6SHFLILNDFLMDLQSUHVNXVQDPHWRGD ,62)',6
Conveyor belts - Electrical conductivity - Specification and test method (ISO/FDIS
284:2012)
Courroies transporteuses - Conductibilité électrique - Spécification et méthode d'essai
(ISO/FDIS 284:2012)
Ta slovenski standard je istoveten z: FprEN ISO 284
ICS:
53.040.20 Deli za transporterje Components for conveyors
kSIST FprEN ISO 284:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST FprEN ISO 284:2012
---------------------- Page: 2 ----------------------
kSIST FprEN ISO 284:2012
EUROPEAN STANDARD
FINAL DRAFT
FprEN ISO 284
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2012
ICS 53.040.10 Will supersede EN ISO 284:2003
English Version
Conveyor belts - Electrical conductivity - Specification and test
method (ISO/FDIS 284:2012)
Courroies transporteuses - Conductibilité électrique -
Spécification et méthode d'essai (ISO/FDIS 284:2012)
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 188.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprEN ISO 284:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST FprEN ISO 284:2012
FprEN ISO 284:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
kSIST FprEN ISO 284:2012
FprEN ISO 284:2012 (E)
Foreword
This document (FprEN ISO 284:2012) has been prepared by Technical Committee ISO/TC 41 "Pulleys and
belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the
secretariat of which is held by SNV.
This document is currently submitted to the Unique Acceptance Procedure.
This document will supersede EN ISO 284:2003.
Endorsement notice
The text of ISO/FDIS 284:2012 has been approved by CEN as a FprEN ISO 284:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
kSIST FprEN ISO 284:2012
---------------------- Page: 6 ----------------------
kSIST FprEN ISO 284:2012
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 284
ISO/TC 41/SC 3
Conveyor belts — Electrical
Secretariat: SAC
conductivity — Specification and test
Voting begins on:
2012-08-09 method
Voting terminates on:
Courroies transporteuses — Conductibilité électrique — Spécification
2012-10-09
et méthode d’essai
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 284:2012(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2012
---------------------- Page: 7 ----------------------
kSIST FprEN ISO 284:2012
ISO/FDIS 284:2012(E)
Copyright notice
This ISO document is a Draft International Standard and is copyrightprotected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
Email copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
kSIST FprEN ISO 284:2012
ISO/FDIS 284:2012(E)
ISO/CEN PARALLEL PROCESSING
This Minor Revision has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This final draft is hereby submitted to a parallel two-month approval vote in ISO and three-month UAP vote in
CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
kSIST FprEN ISO 284:2012
ISO/FDIS 284:2012(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Specification . 1
4 Test method . 1
4.1 Principle . 1
4.2 Materials and apparatus . 1
4.3 Test pieces . 2
4.4 Atmosphere for conditioning and testing . 3
4.5 Procedure . 3
4.6 Expression of results . 4
4.7 Test report . 4
Annex A (informative) Variation of electrical resistance with temperature and humidity .5
Bibliography . 6
iv © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
kSIST FprEN ISO 284:2012
ISO/FDIS 284:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Stan
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.