SIST EN IEC 61754-7-3:2019
(Main)Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7-3: Type MPO connector family - Two fibre rows 16 fibre wide (IEC 61754-7-3:2019)
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7-3: Type MPO connector family - Two fibre rows 16 fibre wide (IEC 61754-7-3:2019)
This part of IEC 61754 defines the standard interface dimensions for type MPO family of
connectors with two rows of 16 fibres.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von Lichtwellenleiter-Steckverbindern - Teil 7-3: Steckverbinderfamilie der Bauart MPO - Zwei Faserreihen mit jeweils 16 Fasern (IEC 61754-7-3:2019)
Dispositifs d'interconnexion et composants passifs àfibres optiques - Interfaces de connecteurs à fibres optiques - Partie 7-3: Famille de connecteurs de type MPO - Deux rangées de 16 fibres (IEC 61754-7-3:2019)
La présente partie de l'IEC 61754 définit les dimensions d’interface normalisées pour la famille de connecteurs de type MPO comportant deux rangées de 16 fibres.
Optični spojni elementi in pasivne komponente - Vmesniki optičnih konektorjev - 7-3. del: Skupina konektorjev vrste MPO - Dvoredni s po 16 vlaken (IEC 61754-7-3:2019)
Ta del standarda IEC 61754 opredeljuje standardne mere vmesnikov za družino konektorjev vrste MPO z dvema redoma 16 vlaken.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61754-7-3:2019
01-oktober-2019
Optični spojni elementi in pasivne komponente - Vmesniki optičnih konektorjev - 7
-3. del: Skupina konektorjev vrste MPO - Dvoredni s po 16 vlaken (IEC 61754-7-
3:2019)
Fibre optic interconnecting devices and passive components - Fibre optic connector
interfaces - Part 7-3: Type MPO connector family - Two fibre rows 16 fibre wide (IEC
61754-7-3:2019)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von
Lichtwellenleiter-Steckverbindern - Teil 7-3: Steckverbinderfamilie der Bauart MPO -
Zwei Faserreihen mit jeweils 16 Fasern (IEC 61754-7-3:2019)
Dispositifs d'interconnexion et composants passifs àfibres optiques - Interfaces de
connecteurs à fibres optiques - Partie 7-3: Famille de connecteurs de type MPO - Deux
rangées de 16 fibres (IEC 61754-7-3:2019)
Ta slovenski standard je istoveten z: EN IEC 61754-7-3:2019
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 61754-7-3:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 61754-7-3:2019
---------------------- Page: 2 ----------------------
SIST EN IEC 61754-7-3:2019
EUROPEAN STANDARD EN IEC 61754-7-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2019
ICS 33.180.20
English Version
Fibre optic interconnecting devices and passive components -
Fibre optic connector interfaces - Part 7-3: Type MPO connector
family - Two fibre rows 16 fibre wide
(IEC 61754-7-3:2019)
Dispositifs d'interconnexion et composants passifs àfibres Lichtwellenleiter - Verbindungselemente und passive
optiques - Interfaces de connecteurs à fibres optiques - Bauteile - Steckgesichter von Lichtwellenleiter-
Partie 7-3: Famille de connecteurs de type MPO - Deux Steckverbindern - Teil 7-3: Steckverbinderfamilie der Bauart
rangées de 16 fibres MPO - Zwei Faserreihen mit jeweils 16 Fasern
(IEC 61754-7-3:2019) (IEC 61754-7-3:2019)
This European Standard was approved by CENELEC on 2019-05-10. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61754-7-3:2019 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61754-7-3:2019
EN IEC 61754-7-3:2019 (E)
European foreword
The text of document 86B/4176/FDIS, future edition 1 of IEC 61754-7-3, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61754-7-3:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-02-10
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-05-10
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61754-7-3:2019 was approved by CENELEC as a
European Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 61754-7-3:2019
IEC 61754-7-3
®
Edition 1.0 2019-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Fibre optic
connector interfaces –
Part 7-3: Type MPO connector family –Two fibre rows 16 fibre wide
Dispositifs d'interconnexion et composants passifs àfibres optiques – Interfaces
de connecteurs à fibres optiques –
Partie 7-3: Famille de connecteurs de type MPO – Deux rangées de 16 fibres
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-6714-1
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 5 ----------------------
SIST EN IEC 61754-7-3:2019
– 2 – IEC 61754-7-3:2019 © IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Description . 6
5 Interfaces . 7
Figure 1 – MPO connector configurations . 7
Figure 2 – Optical datum target location diagrams . 8
Figure 3 – Gauge pin . 8
Figure 4 – Gauge for plug . 9
Figure 5 – MPO female plug, down-angled interface . 10
Figure 6 – MPO female plug, up-angled interface . 10
Figure 7 – MPO male plug, down-angled interface . 12
Figure 8 – MPO male plug, up-angled interface . 13
Figure 9 – MPO female plug, flat interface . 15
Figure 10 – MPO male plug, flat interface . 17
Figure 11 – MPO adaptor interface, opposed keyway configuration . 19
Figure 12 – MPO adaptor interface, aligned keyway configuration . 21
Figure 13 – MPO active device receptacle, angled interface . 23
Figure 14 – MPO active device receptacle, flat interface . 25
Table 1 – Intermateability between plugs and adaptors/housings/receptacles . 7
Table 2 – Dimensions of the gauge pin . 8
Table 3 – Dimensionsof the gauge for plug . 9
Table 4 – Dimensions of the MPO female plug, down- or up-angled interface . 11
Table 5 – Dimensions of the MPO male plug, down- or up-angled interface . 13
Table 6 – Dimensions of the MPO female plug, flat interface . 16
Table 7 – Dimensions of the MPO male plug, flat interface . 18
Table 8 – Dimensions of the MPO adaptor interface, opposed keyway configuration . 20
Table 9 – Dimensions of the MPO adaptor interface, aligned keyway configuration . 22
Table 10 – Dimensions of the MPO active device receptacle, angled interface . 24
Table 11 – Dimensions of the MPO active device receptacle, flat interface . 26
---------------------- Page: 6 ----------------------
SIST EN IEC 61754-7-3:2019
IEC 61754-7-3:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR INTERFACES –
Part 7-3: Type MPO connector family –
Two fibre rows 16 fibre wide
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61754-7-3 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
The text of this International Standard is based on the following documents:
FDIS Report on voting
86B/4176/FDIS 86B/4190/RVD
Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 7 ----------------------
SIST EN IEC 61754-7-3:2019
– 4 – IEC 61754-7-3:2019 © IEC 2019
A list of all parts in the IEC 61754 series, published under the general title Fibre optic
interconnecting devices and passive components – Fibre optic connector interfaces, can be
found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 8 ----------------------
SIST EN IEC 61754-7-3:2019
IEC 61754-7-3:2019 © IEC 2019 – 5 –
INTRODUCTION
The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed
that compliance with this document may involve the use of patents concerning MPO connectors.
The IEC takes no position concerning the evidence, validity and scope of this patent right.
The holders of these patent rights have assured the IEC that they are willing to negotiate
licences under reasonable and non-discriminatory terms and conditions with applicants
throughout the world. In this respect, the statement of the holders of these patent rights is
registered with the IEC. Information may be obtained from:
Intellectual Property Department,
NTT Nippon Telegraph and Telephone Corporation,
3-19-2, Nishishinjuku, Shinjuku-ku
JP – Tokyo 163-19
Assistant Secretary
Laura Thomas
CommScope, Inc. of North Carolina
Hickory, North Carolina, USA
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights other than those identified above. IEC shall not be held responsible for
identifying any or all such patent rights.
ISO (www.iso.org/patents) and IEC (http://patents.iec.ch) maintain on-line data bases of
patents relevant to their standards. Users are encouraged to consult the data bases for the
most up to date information concerning patents.
---------------------- Page: 9 ----------------------
SIST EN IEC 61754-7-3:2019
– 6 – IEC 61754-7-3:2019 © IEC 2019
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR INTERFACES –
Part 7-3: Type MPO connector family –
Two fibre rows 16 fibre wide
1 Scope
This part of IEC 61754 defines the standard interface dimensions for type MPO family of
connectors with two rows of 16 fibres.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Description
The parent connector for type MPO connector family is a multiway plug characterized by a
rectangular ferrule normally 6,4 mm × 2,5 mm which utilizes two pins of 0,55 mm diameter as
its alignment. The variant in this document provides a joint of 32 fibres by arraying them
between two pin-positioning holes in the ferrule in a two-layer (two-row) arrangement. The
connector includes a push-pull coupling mechanism and a ferrule spring loaded in the direction
of the optical axis. The connector has a single male key which may be used to orient and limit
the relative position between the connector and the component to which it is mated.
Connector interfaces are configured using a female plug without pins, a male plug with pins
fixed and an adaptor as shown in Figure 1. The female plug is intermateable with the male plug.
There are two angled-interface plugs, one called down-angled and the other up-angled. They
are defined for both male and female plugs. The up and down descriptors refer to the tilt
direction of the ferrule’s angled end-face relative to the fibre axis when looking toward the end-
face with the plug’s key feature on the top. For down-angled plugs, the angled surface faces
slightly downward. For up-angled plugs, the angled surface faces slightly upward. These
different angles affect intermateability for the two adaptor types. An opposed keyway adaptor
mates two plugs with the keys in opposite orientations, for example one side keyway-up and
the other keyway-down. In contrast, an aligned keyway adaptor mates two plugs with the keys
at the same orientation. When using an opposed keyway adaptor with angled interfaces, two
down-angled plugs or two up-angled plugs shall be connected. For aligned keyway adaptors
with angled interfaces, one down-angled plug and one up-angled plug shall be connected.
Additionally, the female plug interface is intermateable with the active device receptacle.
---------------------- Page: 10 ----------------------
SIST EN IEC 61754-7-3:2019
IEC 61754-7-3:2019 © IEC 2019 – 7 –
5 Interfaces
This document contains the following standard interfaces:
Interface IEC 61754-7-3-1: MPO female plug, down-angled interface for 32 fibres
Interface IEC 61754-7-3-2: MPO male plug, down-angled interface for 32 fibres
Interface IEC 61754-7-3-3: MPO female plug, up-angled interface for 32 fibres
Interface IEC 61754-7-3-4: MPO male plug, up-angled interface for 32 fibres
Interface IEC 61754-7-3-5: MPO female plug, flat interface for 32 fibres
Interface IEC 61754-7-3-6: MPO male plug, flat interface fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.