SIST EN ISO 283:2008
(Main)Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2007)
Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2007)
This Standard describes a method of test for determining the full thickness tensile strength, elongation at break and elongation at the reference load of conveyor belts having a textile construction. Methods are in development for tensile strenghts greater than 2500 N/mm. This standard is not suitable or valid f for light conveyor belts as described in EN 873.
Textilfördergurte - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei Bezugskraft - Prüfverfahren (ISO 283:2007)
Diese Internationale Norm legt ein Prüfverfahren zur Be¬stimmung der Bruchfestigkeit und der Dehnung in Längsrichtung von Textilfördergurten bei voller Gurtdicke fest. Außerdem legt sie das Verfahren zur Bestimmung der Bruchfestigkeit in Querrichtung und die Bruchdehnung in Längsrichtung fest, für den Fall, dass der Käufer den Hersteller auffordert, Werte für den Gebrauch vorzulegen.
Diese Internationale Norm ist nicht gültig oder anwendbar auf die in ISO 21183-1 beschriebenen leichte Fördergurte.
Courroies transporteuses a carcasse textile - Résistance a la traction, allongement a la rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai (ISO 283:2007)
L'ISO 283:2007 spécifie une méthode d'essai pour déterminer la résistance à la traction dans le sens longitudinal et l'allongement sous force de référence et le point de rupture des courroies transporteuses à carcasse textile. La méthode peut également être utilisée pour la détermination de la résistance à la traction dans le sens transversal et de l'allongement au point rupture, utilisables lorsque l'acheteur demande au fabricant de déclarer les valeurs de ces propriétés.
L'ISO 283:2007 n'est pas applicable ou valable pour les courroies transporteuses légères décrites dans l'ISO 21183-1.
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Natezna trdnost pri polni debelini traku, raztezek pri porušitvi in raztezek pri referenčni sili - Metoda preskušanja (ISO 283:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 283:2008
01-maj-2008
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY1DWH]QDWUGQRVW
SULSROQLGHEHOLQLWUDNXUD]WH]HNSULSRUXãLWYLLQUD]WH]HNSULUHIHUHQþQLVLOL0HWRGD
SUHVNXãDQMD ,62
Textile conveyor belts - Full thickness tensile strength, elongation at break and
elongation at the reference load - Test method (ISO 283:2007)
Textilfördergurte - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei
Bezugskraft - Prüfverfahren (ISO 283:2007)
Courroies transporteuses a carcasse textile - Résistance a la traction, allongement a la
rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai
(ISO 283:2007)
Ta slovenski standard je istoveten z: EN ISO 283:2007
ICS:
53.040.20
SIST EN ISO 283:2008 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 283
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 53.040.20 Supersedes EN ISO 283-1:2000
English Version
Textile conveyor belts - Full thickness tensile strength,
elongation at break and elongation at the reference load - Test
method (ISO 283:2007)
Courroies transporteuses à carcasse textile - Résistance à Textilfördergurte - Zugfestigkeit bei voller Gurtdicke,
la traction, allongement à la rupture et allongement sous Bruchdehnung und Dehnung bei breitenbezogener
force de référence en pleine épaisseur - Méthode d'essai Bruchkraft - Prüfverfahren (ISO 283:2007)
(ISO 283:2007)
This European Standard was approved by CEN on 23 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 283:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 283:2007 (E)
Foreword
This document (EN ISO 283:2007) has been prepared by Technical Committee ISO/TC 41
"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188
"Conveyor belts", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2007, and conflicting national
standards shall be withdrawn at the latest by December 2007.
This document supersedes EN ISO 283-1:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
Endorsement notice
The text of ISO 283:2007 has been approved by CEN as EN ISO 283:2007 without any
modifications.
2
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 283
Third edition
2007-06-15
Textile conveyor belts — Full thickness
tensile strength, elongation at break and
elongation at the reference load — Test
method
Courroies transporteuses à carcasse textile — Résistance à la traction,
allongement à la rupture et allongement sous force de référence en
pleine épaisseur — Méthode d'essai
Reference number
ISO 283:2007(E)
©
ISO 2007
---------------------- Page: 4 ----------------------
ISO 283:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 283:2007(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Principle. 2
5 Apparatus. 2
6 Test pieces. 3
6.1 Shape and dimensions. 3
6.2 Method of selection of test pieces. 3
6.3 Preparation of test pieces. 7
6.4 Number of test pieces . 8
6.5 Conditioning of test pieces. 8
7 Procedure. 8
8 Calculation and expression of results. 8
8.1 Tensile strength. 8
8.2 Elongation . 8
9 Test report. 9
Bibliography . 10
© ISO 2007 – All rights reserved iii
---------------------- Page: 6 ----------------------
ISO 283:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 283 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This third edition of ISO 283 cancels and replaces ISO 283-1:2000, of which it constitutes a technical revision.
It also incorporates the Technical Corrigendum ISO 283-1:2000/Cor.1:2006.
iv © ISO 2007 – All rights reserved
---------------------- Page: 7 ----------------------
INTERNATIONAL STANDARD ISO 283:2007(E)
Textile conveyor belts — Full thickness tensile strength,
elongation at break and elongation at the reference load —
Test method
1 Scope
This International Standard specifies a test method for the determination of the
...
SLOVENSKI oSIST prEN ISO 283:2005
PREDSTANDARD
maj 2005
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Natezni
preskus pri polni debelini traku – Specifikacije in metode preskušanja
(ISO/DIS 283:2005)
Conveyor belts - Full thickness tensile strength and elongation - Specifications and
method of test (ISO/DIS 283:2005)
ICS 53.040.20 Referenčna številka
oSIST prEN ISO 283:2005(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN ISO 283
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2005
ICS Will supersede EN ISO 283-1:2000
English version
Conveyor belts - Full thickness tensile strength and elongation -
Specifications and method of test (ISO/DIS 283:2005)
Courroies transporteuses à carcasse textile - Résistance à
la traction, allongement à la rupture et allongement sous
charge de référence en pleine épaisseur - Méthode d'essai
(ISO/DIS 283:2005)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 188.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 283:2005: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
prEN ISO 283:2005 (E)
Foreword
This document (prEN ISO 283:2005) has been prepared by Technical Committee ISO/TC 41
"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC
188 "Conveyor belts", the secretariat of which is held by BSI.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN ISO 283-1:2000.
Endorsement notice
The text of ISO 283:2005 has been approved by CEN as prEN ISO 283:2005 without any
modifications.
2
---------------------- Page: 3 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 283
ISO/TC 41/SC 3 Secretariat: BSI
Voting begins on: Voting terminates on:
2005-02-17 2005-07-17
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Conveyor belts — Full thickness tensile strength and
elongation — Specifications and method of test
Courroies transporteuses à carcasse textile — Résistance à la traction, allongement à la rupture et
allongement sous charge de référence en pleine épaisseur — Méthode d'essai
[Revision of second edition (ISO 283:1990) and ISO 283-1:2000]
ICS 53.040.20
ISO/CEN PARALLEL ENQUIRY
The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject
of interest to European standardization. In accordance with the ISO-lead mode of collaboration as
defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN
members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a
final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS
vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
© International Organization for Standardization, 2005
---------------------- Page: 4 ----------------------
ISO/DIS 283
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2005 – All rights reserved
---------------------- Page: 5 ----------------------
ISO/DIS 283
Contents Page
Foreword. v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions . 1
4 Principle. 2
5 Apparatus. 2
6 Test pieces. 4
6.1 Number of test pieces . 4
6.2 Method of selection of test pieces . 5
6.3 Shape and dimensions. 5
6.4 Preparation of test pieces. 9
6.5 Conditioning of test pieces. 9
7 Procedure. 9
8 Calculation and expression of results . 10
8.1 Breaking strength. 10
8.2 Elongation. 10
9 Test report. 10
Bibliography . 12
© ISO 2005 – All rights reserved iii
---------------------- Page: 6 ----------------------
ISO/DIS 283
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national
standards bodies (ISO member bodies). The work of preparing International Standards is normally
carried out through ISO technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on that committee.
International organizations, governmental and non-governmental, in liaison with ISO, also take part in
the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,
Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 283 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This third edition of ISO 283 cancels and replaces ISO 283-1:2000, of which it constitutes a technical
revision.
iv © ISO 2005 – All rights reserved
---------------------- Page: 7 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 283
Conveyor belts — Full thickness tensile strength and
elongation — Specification
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.