SIST-TS CEN/TS 15534-3:2007
(Main)Wood-plastics composites (WPC) - Part 3: Characterisation of WPC products
Wood-plastics composites (WPC) - Part 3: Characterisation of WPC products
This Technical Specification identifies the required and optional properties of wood-plastics composite (WPC) products. It is intended to be used as a basis for the specifications of WPC products.
This part is applicable to WPC products intended to be used as decking and siding.
NOTE Other applications may be covered when this document will be revised.
Holz-Polymer-Werkstoffe (WPC) - Teil 3: Beschreibung von WPC- Erzeugnissen
Diese Technische Spezifikation legt die geforderten und wahlfreien Eigenschaften von Erzeugnissen aus Holz-Kunststoff-Verbundstoffen (WPC) fest und ist als Grundlage für die Spezifikationen von WPC-Erzeug¬nissen vorgesehen.
Dieser Teil ist anwendbar auf WPC-Erzeugnisse, die für die Verwendung als Bodenbeläge und Seitenbeklei¬dungen bestimmt sind.
ANMERKUNG Bei der Überarbeitung dieses Dokumentes können weitere Anwendungsfälle einbezogen werden.
Composites bois-plastiques (WPC) - Partie 3 : Caractérisation des produits en WPC
La présente Spécification technique identifie les propriétés requises et facultatives des produits en composites bois-plastiques (WPC). Elle est destinée a servir de base aux spécifications des produits en WPC.
La présente partie s’applique aux produits en WPC destinés au platelage et au bardage.
NOTE D’autres applications seront susceptibles d’etre couvertes apres révision de ce document.
Lesno-polimerni kompoziti (WPC) - 3. del: Karakterizacija WPC proizvodov
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 15534-3:2007
01-september-2007
Lesno-polimerni kompoziti (WPC) - 3. del: Karakterizacija WPC proizvodov
Wood-plastics composites (WPC) - Part 3: Characterisation of WPC products
Holz-Polymer-Werkstoffe (WPC) - Teil 3: Beschreibung von WPC- Erzeugnissen
Composites bois-plastiques (WPC) - Partie 3 : Caractérisation des produits en WPC
Ta slovenski standard je istoveten z: CEN/TS 15534-3:2007
ICS:
79.060.01 /HVQHSORãþHQDVSORãQR Wood-based panels in
general
SIST-TS CEN/TS 15534-3:2007 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
TECHNICAL SPECIFICATION
CEN/TS 15534-3
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
May 2007
ICS 79.060.01
English Version
Wood-plastics composites (WPC) - Part 3: Characterisation of
WPC products
Composites bois-plastiques (WPC) - Partie 3 : Holz-Polymer-Werkstoffe (WPC) - Teil 3: Beschreibung von
Caractérisation des produits en WPC WPC- Erzeugnissen
This Technical Specification (CEN/TS) was approved by CEN on 29 December 2006 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15534-3:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
CEN/TS 15534-3:2007 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Characterisation of WPC products .5
Annex A (informative) Technical data templates .7
2
---------------------- Page: 3 ----------------------
CEN/TS 15534-3:2007 (E)
Foreword
This document (CEN/TS 15534-3:2007) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by NBN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
CEN/TS 15534 consists of the following parts, under the general title Wood plastics composites (WPC):
Part 1: Test methods for characterisation of WPC materials and products
Part 2: Characterisation of WPC materials
Part 3: Characterisation of WPC products
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 4 ----------------------
CEN/TS 15534-3:2007 (E)
1 Scope
This Technical Specification identifies the required and optional properties of wood-plastics composite (WPC)
products. It is intended to be used as a basis for the specifications of WPC products.
This part is applicable to WPC products intended to be used as decking and siding.
NOTE Other applications may be covered when this document will be revised.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 310, Wood based panels — Determination of modulus of elasticity in bending and of bending strength
EN 317, Particleboards and fibreboards — Determination of swelling in thickness after immersion in water
EN 318, Wood-based panels — Determination of dimensional changes associated with changes in relative
humidity
EN 321, Wood based panels — Determination of moisture resistance under cyclic test conditions
EN 477, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors —
Determination of the resistance to impact of main profiles by falling mass
EN 479, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors —
Determination of heat reversion
EN 789:2004, Timber structures — Test methods — Determination of mechanical properties of wood based
panels
EN 927-6, Paints and varnishes — Coating materials and coating systems for exterior wood — Part 6:
Exposure of wood coatings to artificial weathering using fluorescent UV lamps and water
ENV 1156, Wood-based panels — Determination of duration of load and creep factors
EN 1383, Timber structures — Test methods — Pull through resistance of timber fasteners
EN 13446, Wood-based panels — Determination of withdrawal capacity of fasteners
EN 13823, Reaction to fire tests for building products — Building products excluding floorings exposed to the
thermal attack by a single burning item
EN 13893, Resilient, laminate and textile floor coverings — Measurement of dynamic coefficient of friction on
dry floor surfaces
CEN/TS 15534-1:2007, Wood-plastics composites (WPC) — Part 1: Test methods for characterisation of
WPC materials and products
CEN/TS 15534-2, Wood-plastics composites (WPC) — Part 2: Characterisation of WPC materials
4
---------------------- Page: 5 ----------------------
CEN/TS 15534-3:2007 (E)
EN ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
(ISO 179-1:2000)
EN ISO 877, Plastics — Methods for exposure to direct weathering, to weathering using glass-filtered daylight,
and to intensified weathering by daylight using Fresnel mirrors (ISO 877:1994)
EN ISO 2813, Paints and varnishes -- Determination of specular gloss of non-metallic paint films at 20
degrees, 60 degrees and 85 degrees (ISO 2813:1994, including Technical Corrigendum 1:1997)
EN ISO 4628-6, Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and
size of defects, and of intensity of uniform changes in appearance — Part 6: Assessment of degree of
chalking by tape method (ISO 4628-6:2006)
EN ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
(ISO 4892-2:2006)
EN ISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2:
Instrumented puncture test (ISO 6603-2:2000)
EN ISO 9142:2003, Adhesives — Guide to the selection of standard laboratory ageing conditions for testing
bonded joints (ISO 9142:2003)
EN ISO 9239-1, Reaction to fire tests for floorings — Part 1: Determination of the burning behaviour using a
radiant heat source (ISO 9239-1:2002)
EN ISO 11925-2, Reaction to fire tests — Ignitability of building products subjected to direct impingement of
flame — Part 2: Single-flame source test (ISO 11925-2:2002)
ISO 7724-1, Paints and varnishes — Colorimetry — Part 1: Principles
ISO 7724-2, Paints and varnishes — Colorimetry — Part 2: Colour measurement
ISO 7724-3, Paints and varnishes — Colorimetry — Part 3: Calculation of colour differences
3 Characterisation of WPC products
The characteristics of WPC products, given in Table 1, are divided into two types:
required characteristics needed to characterize all WPC products;
optional characteristics needed to char
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.