SIST EN ISO 15912:2006/A1:2011
(Amendment)Dentistry - Casting investments and refractory die materials - Amendment 1: Requirement and test method for adequacy of expansion of Type 1 and Type 2 materials (ISO 15912:2006/A1:2011)
Dentistry - Casting investments and refractory die materials - Amendment 1: Requirement and test method for adequacy of expansion of Type 1 and Type 2 materials (ISO 15912:2006/A1:2011)
This International Standard is applicable to dental casting, brazing and refractory investments and refractory die materials, regardless of the nature of the binding system or the particular application. This International Standard classifies investments into types according to their intended use and classes according to the burn-out procedure recommended by the manufacturer. This International Standard specifies requirements for the essential physical and mechanical properties of the materials and the test methods used to determine them. This International Standard also includes requirements for the information and instructions which accompany each package.
Zahnheilkunde - Einbettmassen und hochtemperaturbeständige Stumpfmaterialien - Änderung 1 (ISO 15912:2006/A1:2011)
Art dentaire - Revêtements et matériaux pour modèles réfractaires - Amendement 1: Exigence et méthode d'essai pour l'adéquation d'expansion des matériaux de Type 1 et de Type 2 (ISO 15912:2006/A1:2011)
Zobozdravstvo - Polnila in refrakcijski materiali - Dopolnilo 1: Zahteve in preskusne metode za primernost ekspanzije materiala tipa 1 in tipa 2 - Dopolnilo A1 (ISO 15912:2006/A1:2011)
Ta mednarodni standard velja za zobna polnila, pritrdila in refrakcijske materiale, ne glede na naravo vezalnega sistema ali določene uporabe. Ta mednarodni standard razvršča polnila na vrste v skladu z njihovo predvideno uporabo in razrede v skladu z izgorevalnim postopkom, ki ga priporoča proizvajalec. Ta mednarodni standard določa zahteve za bistvene fizične in mehanske lastnosti materialov in preskusne metode, ki se uporabljajo za njihovo določevanje. Ta mednarodni standard prav tako vključuje zahteve za informacije in navodila, ki spremljajo vsak paket.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15912:2006/A1:2011
01-oktober-2011
Zobozdravstvo - Polnila in refrakcijski materiali - Dopolnilo 1: Zahteve in
preskusne metode za primernost ekspanzije materiala tipa 1 in tipa 2 - Dopolnilo
A1 (ISO 15912:2006/A1:2011)
Dentistry - Casting investments and refractory die materials - Amendment 1:
Requirement and test method for adequacy of expansion of Type 1 and Type 2 materials
(ISO 15912:2006/A1:2011)
Zahnheilkunde - Einbettmassen und hochtemperaturbeständige Stumpfmaterialien -
Änderung 1 (ISO 15912:2006/A1:2011)
Art dentaire - Revêtements et matériaux pour modèles réfractaires - Amendement 1:
Exigence et méthode d'essai pour l'adéquation d'expansion des matériaux de Type 1 et
de Type 2 (ISO 15912:2006/A1:2011)
Ta slovenski standard je istoveten z: EN ISO 15912:2006/A1:2011
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
SIST EN ISO 15912:2006/A1:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15912:2006/A1:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 15912:2006/A1:2011
EUROPEAN STANDARD
EN ISO 15912:2006/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2011
ICS 11.060.10
English Version
Dentistry - Casting investments and refractory die materials -
Amendment 1: Requirement and test method for adequacy of
expansion of Type 1 and Type 2 materials (ISO
15912:2006/Amd 1:2011)
Art dentaire - Revêtements et matériaux pour modèles Zahnheilkunde - Einbettmassen und
réfractaires - Amendement 1: Exigence et méthode d'essai
hochtemperaturbeständige Stumpfmaterialien - Änderung 1
pour l'adéquation d'expansion des matériaux de Type 1 et (ISO 15912:2006/Amd 1:2011)
de Type 2 (ISO 15912:2006/Amd 1:2011)
This amendment A1 modifies the European Standard EN ISO 15912:2006; it was approved by CEN on 14 July 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15912:2006/A1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15912:2006/A1:2011
EN ISO 15912:2006/A1:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15912:2006/A1:2011
EN ISO 15912:2006/A1:2011 (E)
Foreword
This document (EN ISO 15912:2006/A1:2011) has been prepared by Technical Committee ISO/TC 106
"Dentistry" in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by
DIN.
This Amendment to the European Standard EN ISO 15912:2006 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by January 2012, and
conflicting national standards shall be withdrawn at the latest by January 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15912:2006/Amd 1:2011 has been approved by CEN as a EN ISO 15912:2006/A1:2011
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15912:2006/A1:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 15912:2006/A1:2011
INTERNATIONAL ISO
STANDARD 15912
First edition
2006-10-01
AMENDMENT 1
2011-07-15
Dentistry — Casting investments and
refractory die materials
AMENDMENT 1: Requirement and test
method for adequacy of expansion of Type 1
and Type 2 materials
Art dentaire — Revêtements et matériaux pour modèles réfractaires
AMENDEMENT 1: Exigence et méthode d'essai pour l'adéquation
d'expansion des matériaux de Type 1 et de Type 2
Reference number
ISO 15912:2006/Amd.1:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 15912:2006/A1:2011
ISO 15912:2006/Amd.1:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15912:2006/A1:2011
ISO 15912:2006/Amd.1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. I
...
SLOVENSKI STANDARD
SIST EN ISO 15912:2006/oprA1:2010
01-marec-2010
Zobozdravstvo - Polnila in refrakcijski materiali - Dopolnilo 1 (ISO 15912:2006/DAM
1:2010)
Dentistry - Casting investments and refractory die materials - Amendment 1 (ISO
15912:2006/DAM 1:2010)
Zahnheilkunde - Einbettmassen und hochtemperaturbeständige Stumpfmaterialien -
Änderung 1 (ISO 15912:2006/DAM 1:2010)
Art dentaire - Revêtements et matériaux pour modèles réfractaires - Amendement 1 (ISO
15912:2006/DAM 1:2010)
Ta slovenski standard je istoveten z: EN ISO 15912:2006/prA1
ICS:
11.060.10 =RERWHKQLþQLPDWHULDOL Dental materials
SIST EN ISO 15912:2006/oprA1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15912:2006/oprA1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 15912:2006/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN ISO 15912:2006
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2010
ICS 11.060.10
English Version
Dentistry - Casting investments and refractory die materials -
Amendment 1 (ISO 15912:2006/DAM 1:2010)
Art dentaire - Revêtements et matériaux pour modèles Zahnheilkunde - Einbettmassen und
réfractaires - Amendement 1 (ISO 15912:2006/DAM hochtemperaturbeständige Stumpfmaterialien - Änderung 1
1:2010) (ISO 15912:2006/DAM 1:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 55.
This draft amendment A1, if approved, will modify the European Standard EN ISO 15912:2006. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15912:2006/prA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15912:2006/oprA1:2010
EN ISO 15912:2006/prA1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15912:2006/oprA1:2010
EN ISO 15912:2006/prA1:2010 (E)
Foreword
This document (EN ISO 15912:2006/prA1:2010) has been prepared by Technical Committee ISO/TC 106
“Dentistry” in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by
DIN.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 15912:2006/DAM 1:2010 has been approved by CEN as a EN ISO 15912:2006/prA1:2010
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15912:2006/oprA1:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 15912:2006/oprA1:2010
DRAFT AMENDMENT ISO 15912:2006/DAmd 1
ISO/TC 106/SC 2 Secretariat: ANSI
Voting begins on: Voting terminates on:
2010-01-21 2010-06-21
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Dentistry — Casting investments and refractory die materials
AMENDMENT 1
Art dentaire — Revêtements et matériaux pour modèles réfractaires
AMENDEMENT 1
ICS 11.060.10
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 15912:2006/oprA1:2010
ISO 15912:2006/DAmd 1
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.