SIST EN 302 217-2-1 V1.2.1:2007
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied
The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced in two different clauses sub-sets:
• Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of the R&TTE Directive [1] and further detailed in EN 302 217-2-2 [16].
• Complementary requirements are requirements that are not related to essential requirements under article 3.2 of the R&TTE Directive [1]. Nevertheless they are considered having been commonly agreed for proper system operation and deployment when specific deployment conditions or compatibility requirements are present. Compliance to all or some of these requirements is made on a voluntary basis. Description and limits for parameters relevant to essential requirements under article 3.2 of R&TTE Directive [1] are given in EN 302 217-2-2 [16]. For other system-dependent parameters where standardization is required but that do not affect the R&TTE Directive "essential requirements" mentioned above, description and limits are detailed in the present document in the annexes A to G, subdivided by frequency band or specific applications. The present document deals with Radio Frequency (RF) and base-band equipment characteristics; antenna system requirements are covered in EN 302 217-4-1 (see bibliography) and EN 302 217-4-2 (see bibliography). The present document does not cover test procedures and test conditions which are set out in EN 301 126-1 [14]. As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, different equipment classes are defined in EN 302 217-2-2 [16]. The spectral efficiency classes are indicative only and do not imply any constraint to the actual modulation format, provided that all the requirements in the relevant parts of this EN 302 217 series are met. In some cases, where within the same spectral efficiency class there are different applications, (e.g. for multi-channel trunk or single channel operation), that justify different radio frequency parameters, two different equipment "types" (e.g. type 1 and 2) are provided. Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R&TTE Directive [1] for DFRS may be found in TR 101 506 (see bibliography). Technical background for most of the parameters and requirements referred to in this EN 302 217 series may be found in TR 101 036-1 (see bibliography).
Fiksni radijski sistemi - Karakteristike in zahteve za opremo in antene tipa točka-točka - 2-1. del: Sistemsko odvisne zahteve za digitalne sisteme, ki delujejo v frekvenčnih pasovih, kjer se uporablja frekvenčna koordinacija
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 2-1: System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied33.120.40AnteneAerials33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:EN 302 217-2-1 Version 1.2.1SIST EN 302 217-2-1 V1.2.1:2007en01-december-2007SIST EN 302 217-2-1 V1.2.1:2007SLOVENSKI
STANDARD
SIST EN 302 217-2-1 V1.2.1:2007
ETSI EN 302 217-2-1 V1.2.1 (2007-06)European Standard (Telecommunications series) Fixed Radio Systems;Characteristics and requirements forpoint-to-point equipment and antennas;Part 2-1: System-dependent requirementsfor digital systems operating in frequency bandswhere frequency co-ordination is applied
SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 2
Reference REN/TM-04167-2-1 Keywords DFRS, digital, DRRS, FWA, point-to-point, radio, regulation, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2007. All rights reserved.
DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 3
Contents Intellectual Property Rights.6 Foreword.6 Introduction.6 1 Scope.7 2 References.8 3 Definitions, symbols and abbreviations.9 3.1 Definitions.9 3.2 Symbols.10 3.3 Abbreviations.10 4 General characteristics.10 4.1 Frequency bands and channel arrangements.10 4.2 Special compatibility requirements between systems.10 4.3 Transmission capacity and spectral efficiency.11 5 Main requirements.12 5.1 Transmitter characteristics.12 5.1.1 Transmitter power.12 5.1.2 Transmitter power and frequency control.12 5.1.2.1 Transmitter power control (ATPC and RTPC).12 5.1.2.1.1 Automatic Transmitter Power Control (ATPC).12 5.1.2.1.2 Remote Transmitter Power Control (RTPC).13 5.1.2.2 Remote Frequency Control (RFC).13 5.1.3 Transmitter output power tolerance.13 5.1.4 Radio Frequency (RF) spectrum mask.13 5.1.5 Discrete CW components exceeding the spectrum mask limit.14 5.1.5.1 Discrete CW components at the symbol rate.14 5.1.5.2 Other discrete CW components exceeding the spectrum mask limit.14 5.1.6 Spurious emissions - external.14 5.1.7 Radio frequency tolerance.14 5.2 Receiver characteristics.15 5.2.1 Spurious emissions-external.15 5.3 System performance without diversity.15 5.3.1 BER as a function of receiver signal level.15 5.3.2 Interference sensitivity.15 5.3.2.1 Co-channel "external" interference sensitivity.15 5.3.2.2 Adjacent channel interference sensitivity.15 5.3.2.3 CW spurious interference.16 6 Complementary requirements.16 6.1 Branching/feeder requirements.16 6.1.1 Waveguide flanges (or other connectors).16 6.1.2 Return loss at equipment antenna port (C/C' reference point).17 6.2 Intermodulation products.17 6.3 Transmitter characteristics.17 6.3.1 Spurious emissions - internal.17 6.4 Receiver characteristics.18 6.4.1 Input level range.18 6.4.2 Spurious emissions - internal.19 6.4.3 Image rejection.20 6.4.4 Innermost channel selectivity.20 6.5 System performance without diversity.20 6.5.1 Equipment Residual BER (RBER).20 6.5.2 Interference sensitivity for CCDP with XPIC operation.21 6.5.2.1 Co-channel "internal" interference sensitivity in flat fading conditions.22 SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 4
6.5.2.2 Co-channel "internal" interference sensitivity under dispersive fading conditions.22 6.5.3 Distortion sensitivity.22 6.6 System characteristics with diversity.23 6.6.1 Differential delay compensation.23 6.6.2 BER performance.23 Annex A (normative): Frequency bands from 1,4 GHz to 2,7 GHz.24 A.0 Introduction.24 Annex B (normative): Frequency bands from 3 GHz to 11 GHz (channel separation up to 30 MHz and 56 / 60 MHz).25 B.0 Introduction.25 B.1 System B.1 (2 - 2 × 34 Mbit/s; STM-0 - 2 × STM-0 / 3 GHz to 11 GHz / 1,75 MHz to 29,65 MHz).26 B.1.1 Distortion sensitivity.26 B.2 System B.2 (STM-1 / 3 GHz to 10,5 GHz / about 30 MHz ACAP).26 B.2.1 Radio Frequency (RF) spectrum mask.26 B.2.2 Receiver innermost channel selectivity.29 B.3 System B.3 (2 × STM-1 / 3 GHz to 10,5 GHz / about 30 MHz CCDP).29 B.3.1 Radio Frequency (RF) spectrum mask.29 B.3.2 Innermost channel selectivity.31 B.3.3 Distortion sensitivity.32 B.4 System B.4 (4 × STM-0 / 5 × 34 / 3 GHz to 10,5 GHz / about 30 MHz ACAP).33 B.5 System B.5 (8 × STM-0 / 10 × 34 / 3 GHz to 10,5 GHz / about 60 MHz ACAP).33 B.6 System B.6 (2 × STM1 (ACCP) or STM-4 / 4× STM1 (CCDP) / 3 GHz to 10,5 GHz / about 60 MHz).33 Annex C (normative): Frequency bands from 3 GHz to 11 GHz (channel separation 40 MHz).34 C.0 Introduction.34 C.1 System C.1 (2 × STM-1 / 3 GHz to 11 GHz / 40 MHz - CCDP).34 C.1.1 Radio Frequency (RF) spectrum mask.35 C.1.2 Distortion sensitivity.36 C.2 System C.2 (2 × STM-1 / 3 GHz to 11 GHz / 40 MHz - ACAP).36 C.2.1 Radio Frequency (RF) spectrum mask.36 C.2.2 Receiver input level range.37 C.3 System C.3 (4 × STM-1 / 3 GHz to 11 GHz / 40 MHz - CCDP).37 C.3.1 Transmitter Radio Frequency (RF) spectrum mask.37 C.3.2 Receiver input level range.38 C.3.3 Distortion sensitivity.38 Annex D (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz.39 D.0 Introduction.39 D.1 System D.1 (2 / 2 × 34 Mbit/s / 13 GHz, 15 GHz and 18 GHz / 1,75 MHz / 28 MHz).40 D.1.1 Distortion sensitivity.40 D.2 System D.2 (sub STM-0 / 18 GHz / 3,5 MHz).40 D.3 System D.3 (STM-0 / 13 GHz, 15 GHz and 18 GHz / 28 MHz ACCP-14 MHz ACAP).41 D.4 System D.4 (STM-0 / 13 GHz, 15 GHz and 18 GHz / 14 MHz ACCP).41 D.4.1 Distortion sensitivity.41 D.5 System D.5 (STM-1 / 13 GHz and 15 GHz / about 30 MHz ACAP).41 SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 5
D.6 System D.6 (2 × STM-1 / 13 GHz and 15 GHz / about 30 MHz CCDP).41 D.7 System D.7 (STM-1 / 18 GHz / 27,5 MHz and 55 MHz).42 D.7.1 RF spectrum mask.42 D.7.1.1 Class 4 equipment.42 D.7.1.2 Class 5B equipment.43 D.7.2 Distortion sensitivity.43 D.8 System D.8 (2 × STM-1 (ACCP) and STM-4 (CCDP) / 13 GHz, 15 GHz and 18 GHz / 55 MHz and 56 MHz).43 D.9 System B.4 (4 × STM-0 / 5 × 34 / 13 GHz, 15 GHz and 18 GHz / 27,5 MHz and 28 MHz ACAP).43 D.10 System B.5 (8 × STM-0 / 10 × 34 / 13 GHz, 15 GHz and 18 GHz / 55 MHz and 56 MHz ACAP).44 Annex E (normative): Frequency bands from 23 GHz to 55 GHz.45 E.0 Introduction.45 E.1 Systems E.1, E.2 and E.3: Transmitter spectrum mask for class 5B equipment.46 Annex F (normative): Transmission of packet data and combinations of other signals in bands from 3 GHz to 55 GHz.47 F.1 Introduction.47 F.2 General characteristics.47 F.2.1 Frequency characteristics and channel arrangements.47 F.2.2 Transmission capacities and equipment assessment.47 Annex G (informative): Additional information.48 G.1 Residual Bit Error Ratio (RBER) and Frame Error Ratio (RFER).48 G.2 Measurement test set for XPI characteristics.49 G.3 Differential delay compensation range.50 G.4 FER/BER equivalence and FER performance measurement equipment settings (example).50 G.4.1 FER/BER equivalence.50 G.4.2 FER equipment settings and measurement techniques (example).51 G.5 Automatic Transmitter Power Control (ATPC).51 Annex H (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band).53 Annex I (informative): Bibliography.54 History.55
SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 6
Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM). The present document is part 2-1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas, as identified below: Part 1: "Overview and system-independent common characteristics"; Part 2-1: "System-dependent requirements for digital systems operating in frequency bands where frequency co-ordination is applied"; Part 2-2: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for digital systems operating in frequency bands where frequency co-ordination is applied"; Part 3: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for equipment operating in frequency bands where simplified or no frequency co-ordination procedures are applied"; Part 4-1: "System-dependent requirements for antennas"; Part 4-2: "Harmonized EN covering essential requirements of Article 3.2 of R&TTE Directive for antennas".
National transposition dates Date of adoption of this EN: 15 June 2007 Date of latest announcement of this EN (doa): 30 September 2007 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 March 2008 Date of withdrawal of any conflicting National Standard (dow): 31 March 2008
Introduction The introduction of EN 302 217-1 [15] applies. SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 7
1 Scope The present document summarizes all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced in two different clauses sub-sets:
• Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of the R&TTE Directive [1] and further detailed in EN 302 217-2-2 [16]. • Complementary requirements are requirements that are not related to essential requirements under article 3.2 of the R&TTE Directive [1]. Nevertheless they are considered having been commonly agreed for proper system operation and deployment when specific deployment conditions or compatibility requirements are present. Compliance to all or some of these requirements is made on a voluntary basis. Description and limits for parameters relevant to essential requirements under article 3.2 of R&TTE Directive [1] are given in EN 302 217-2-2 [16]. For other system-dependent parameters where standardization is required but that do not affect the R&TTE Directive "essential requirements" mentioned above, description and limits are detailed in the present document in the annexes A to G, subdivided by frequency band or specific applications. The present document deals with Radio Frequency (RF) and base-band equipment characteristics; antenna system requirements are covered in EN 302 217-4-1 (see bibliography) and EN 302 217-4-2 (see bibliography). The present document does not cover test procedures and test conditions which are set out in EN 301 126-1 [14]. As the maximum transmission rate in a given bandwidth depends on system spectral efficiency, different equipment classes are defined in EN 302 217-2-2 [16]. The spectral efficiency classes are indicative only and do not imply any constraint to the actual modulation format, provided that all the requirements in the relevant parts of this EN 302 217 series are met. In some cases, where within the same spectral efficiency class there are different applications, (e.g. for multi-channel trunk or single channel operation), that justify different radio frequency parameters, two different equipment "types" (e.g. type 1 and 2) are provided. Guidance on the definition of radio parameters relevant to the essential requirements under article 3.2 of R&TTE Directive [1] for DFRS may be found in TR 101 506 (see bibliography).
Technical background for most of the parameters and requirements referred to in this EN 302 217 series may be found in TR 101 036-1 (see bibliography). SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 8
2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. [1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [2] CENELEC EN 122150: "Sectional Specification: Radio frequency coaxial connectors - Series EIA flange". [3] CEPT/ERC/DEC(00)07: "ERC Decision of 19 October 2000 on the shared use of the band 17.7 - 19.7 GHz by the fixed service and Earth stations of the fixed-satellite service (space-to-Earth)". [4] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction". [5] ETSI EN 300 019-1-1: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-1: Classification of environmental conditions; Storage". [6] ETSI EN 300 019-1-2: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-2: Classification of environmental conditions; Transportation". [7] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of environmental conditions; Stationary use at weatherprotected locations". [8] ETSI EN 300 019-1-4: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-4: Classification of environmental conditions; Stationary use at non-weatherprotected locations". [9] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-0: Specification of environmental tests; Introduction". [10] ETSI EN 300 019-2-1: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-1: Specification of environmental tests; Storage". [11] ETSI EN 300 019-2-2: "Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-2: Specification of environmental tests; Transportation". [12] ETSI EN 300 019-2-3: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-3: Specification of environmental tests; Stationary use at weatherprotected locations". SIST EN 302 217-2-1 V1.2.1:2007
ETSI ETSI EN 302 217-2-1 V1.2.1 (2007-06) 9
[13] ETSI EN 300 019-2-4: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of environmental tests; Stationary use at non-weatherprotected locations". [14] ETSI EN 301 126-1: "Fixed Radio Systems; Conformance testing; Part 1: Point-to-Point equipment - Definitions, general requirements and test
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.