Aerospace series - Blind bolt, 100° flush head, high strength

This European Standard specifies the configuration, dimension, tolerances and mass of a stainless steel
blind bolt with 100° flush head for aerospace application.

Luft- und Raumfahrt - Blindniet 100° Senkkopf, hochfet

Diese Europäische Norm legt die Ausführung, Maße, Toleranzen und Masse von Blindnieten aus nichtrostendem Stahl mit 100° Senkkopf für die Anwendung in der Luft- und Raumfahrt fest.

Série aérospatiale - Boulon aveugle tête fraisée 100° haute résistance

Aeronavtika - Slepa kovica, 100° ugrezna glava, zelo trdna

Ta evropski standard določa konfiguracijo, mere, tolerance in maso slepih kovic iz nerjavnega jekla s 100° vgrezno glavo za uporabo v aeronavtiki.

General Information

Status
Published
Publication Date
23-Oct-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
13-Oct-2017
Due Date
18-Dec-2017
Completion Date
24-Oct-2017

Buy Standard

Standard
EN 6128:2017
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Slepa kovica, 100° ugrezna glava, zelo trdnaLuft- und Raumfahrt - Blindniet 100° Senkkopf, hochfetSérie aérospatiale - Boulon aveugle tête fraisée 100° haute résistanceAerospace series - Blind bolt, 100° flush head, high strength49.030.20Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN 6128:2017SIST EN 6128:2017en,fr,de01-december-2017SIST EN 6128:2017SLOVENSKI
STANDARD



SIST EN 6128:2017



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 6128
October
t r s y ICS
v {ä r u rä { { English Version
Aerospace series æ Blind boltá
s r r ¹ flush headá high strength Série aérospatiale æ Boulon aveugle tête fraisée
s r r ¹á haute résistance
Luftæ und Raumfahrt æ Blindniet
s r r ¹ Senkkopfá hochfetThis European Standard was approved by CEN on
t July
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
x s t zã t r s y ESIST EN 6128:2017



EN 6128:2017 (E)
2 Contents
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Requirements . 4 3.1 Configuration, dimensions and tolerances . 4 3.2 Grip range and weight . 4 3.3 Material, finish and lubrication . 5 4 Designation. 13 5 Marking . 14 6 Technical specification . 14
SIST EN 6128:2017



EN 6128:2017 (E) 3 European foreword This document (EN 6128:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 6128:2017



EN 6128:2017 (E)
4 1 Scope This European Standard specifies the configuration, dimension, tolerances and mass of a stainless steel blind bolt with 100° flush head for aerospace application. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2424, Aerospace series — Marking of aerospace products EN 4473, Aerospace series — Aluminium pigmented coatings for fasteners — Technical specification1) AS 5272, Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting, Procurement Specification2) AMS 5687, Nickel Alloy, Corrosion and Heat Resistant, Wire 74Ni 15.5Cr 8.0Fe, Annealed2) AMS 5690, Steel, Corrosion and Heat Resistant, Wire 17Cr-12Ni-2.5Mo (316) Solution Heat Treated2)
AMS 5737, Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings and Tubing 15Cr 25.5Ni 1.2Mo 2.1Ti 0.006B 0.30V, Consumable Electrode Melted, 1650 °F (899 °C), Solution and Precipitation Heat Treated2) AMS-QQ-P-35, Passivation Treatments for Corrosion-Resistant Steel2) MIL-PRF-46010, Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting NATO Code — S-17383) MIL-L-87132, Lubricant, CETYL Alcohol, 1-Hexadecanol, Application to Fasteners3) NASM 8975, Fastener, blind, high strength, installation formed corrosion resistant steel, heat resistant steel and titanium — General specification for3) DOD-L-85645, Lubricant, dry film, molecular bonded3) 3 Requirements 3.1 Configuration, dimensions and tolerances The configuration, dimensions, tolerances, static and dynamic values shall conform to Figure 1 and Figure 2 and Table 1 and Table 2. 3.2 Grip range and weight See Table 3 and Table 4.
1) Published as ASD-STAN pre-standard at the date of publication of the present standard. www.asd-stan.org 2) Published by: Society of Automotive Engineers (SAE), 400 Commonwealth drive, Warrendale, PA 15096-0001, USA 3) Published by: Department of Defense (DOD), the Pentagon, Washington, D.C. 20301. SIST EN 6128:2017



EN 6128:2017 (E) 5 3.3 Material, finish and lubrication See Table 5 and Table 6.
SIST EN 6128:2017



EN 6128:2017 (E)
6 Detail of serrated pin geometry:
Detail A Detail A
Optional configuration Key 1 Marking see clause 5 2 Serrated pin 3 Sleeve 4 Grip 5 Locking collar 6 Shifting Anvil 7 Drive washer a Diameter of pin head shall not exceed “Î D” max. b Fasteners are supplied with shifting anvil / drive washer of manufacturer's option. The shifting anvil / drive washer is not part of the installed fastener. Figure 1 — Configuration – Dimensions SIST EN 6128:2017



EN 6128:2017 (E) 7
Key 1 Grip a Blind side head may be installed on 7° max slope; 5° max slope for diameter code 10 and 12. Figure 2 — Typical installation SIST EN 6128:2017



EN 6128:2017 (E)
8 Table 1 — Dimensions and tolerances Dimensions in mm (inch) Diameter code ÎA B C ÎD ÎJa
N Q ÎD1 ÎD2 ÎW H Pb ÎP2
Theor.
max.
Ref. Ref. max. ±0,025 (±.001) ±0,127 (±.005) ±1,52 (±.060) ±0,13 (±.005) max. max. Gage dia. Gage height max. min.
05 8,48 (.334) 1,88 (.074) 0,28 (.011) 4,14 (.163) 9,53 (.375) 3,56 (.140) 1,70 (.067) 3,05 (.120) 2,16 (.085) 7,193 7,188 (.2832) (.2830) 0,523 0,434 (.0206) (.0171) 7,62 (.300) 5,66 (.223)
06 9,83 (.387) 2,08 (.082) 0,33 (.013) 5,03 (.198) 9,53 (.375) 4,06 (.160) 2,21 (.087) 3,81 (.150) 2,7 (.110) 8,311 8,306 (.3272) (.3270) 0,617 0,521 (.0243) (.0205) 8,13 (.320) 6,86 (.27)
08 12,90 (.508) 2,74 (.108) 0,43 (.017) 6,58 (.259) 9,53 (.375) 4,83 (.190) 2,79 (.110) 4,83 (.190) 3,66 (.144) 10,973 10,968 (.4320) (.4318) 0,787 0,686 (.0310) (.0270) 9,40 (.370) 8,89 (.35)
10 16,13 (.635) 3,56 (.140) 0,51 (.020) 7,90 (.311) 11,13 (.438) 3,94 (.155) 3,35 (.132) 5,88 (.231) 4,62 (.182) 13,846 13,840 (.5451) (.5449) 0,932 0,826 (.0367) (.0325) 8,89 (.350) 9,47 (.373)
12 19,38 (.763) 4,27 (.168) 0,58 (.023) 9,47 (.373) 12,70 (.500) 4,95 (.195) 4,01 (.158) 7,06 (.278) 5,69 (.224) 16,718 16,713 (.6582) (.6580) 1,087 0,965 (.0428) (.0380) 10,29 (.405) 11,38 (.448)
Diameter code R S J1 J2 X E C1 C2 F G Hole limits
min.
max. max. ±0,76 ±.030) Number of serrations ±0,76 (±.030) min. Ref. ±0,05 (±.002) ±5° ±5° min. max.
05 0,25 (.010) 5,89 (.232) 20,32 (.800) 18 1,52 (.060) 0,13 (.005) 0,33 (.013) 0,81 (.032) 45° 30° 4,17 (.164) 4,24 (.167)
06 0,38 (.015) 7,42 (.292) 21,08 (.830) 19 1,78 (.070) 0,13 (.005) 0,33 (.013) 0,81 (.032) 45° 30° 5,06 (.199) 5,13 (.202)
08 0,51
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.