SIST EN 3272:2004
(Main)Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for ferrule, welded - Geometric configuration
Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for ferrule, welded - Geometric configuration
This standard specifies the dimensions of the dynamic beam seal end for welded ferrules for pipe couplings 8°30', nominal pressure up to 28 000 kPa, for aerospace applications.
Luft- und Raumfahrt - Rohrverschraubung 8°30' - Dichtlippe für Anschweißstutzen - Konstruktionsblatt
Diese Norm legt die Maße der Dichtlippe für Anschweißstutzen für Rohrverschraubungen 8°30', Nenndruck bis 28 000 kPa, zur Verwendung in der Luft- und Raumfahrt fest.
Série aérospatiale - Systeme de raccordement 8°30' - Joints a levre pour olive a souder - Configuration géométrique
La présente norme spécifie les dimensions des joints a levre pour olive a souder pour les systemes de raccordement 8°30', pression nominale jusqu'a 28 000 kPa, pour applications aérospatiales.
Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for ferrule, welded - Geometric configuration
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Pipe coupling 8°30' - Dynamic beam seal end for ferrule, welded - Geometric configurationLuft- und Raumfahrt - Rohrverschraubung 8°30' - Dichtlippe für Anschweißstutzen - KonstruktionsblattSérie aérospatiale - Systeme de raccordement 8°30' - Joints a levre pour olive a souder - Configuration géométriqueAerospace series - Pipe coupling 8°30' - Dynamic beam seal end for ferrule, welded - Geometric configuration49.080Aerospace fluid systems and componentsICS:Ta slovenski standard je istoveten z:EN 3272:2001SIST EN 3272:2004en01-maj-2004SIST EN 3272:2004SLOVENSKI
STANDARD
SIST EN 3272:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3272October 2001ICS 49.080English versionAerospace series - Pipe coupling 8°30' - Dynamic beam sealend for ferrule, welded - Geometric configurationSérie aérospatiale - Système de raccordement 8°30' - Jointà lèvre pour olive soudée - Configuration géométriqueLuft- und Raumfahrt - Rohrverschraubung 8°30' - Dichtlippefür Anschweißstutzen - KonstruktionsblattThis European Standard was approved by CEN on 29 December 2000.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3272:2001 ESIST EN 3272:2004
EN 3272:2001 (E)2ForewordThis European Standard has been prepared by the European Association of Aerospace Manufacturers(AECMA).After inquiries and votes carried out in accordance with the rules of this Association, this Standard hasreceived the approval of the National Associations and the Official Services of the member countries ofAECMA, prior to its presentation to CEN.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by April 2002, and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.