SIST EN 16511:2014
(Main)Loose-laid panels - Multi-layer semi-rigid floor covering (MSF) panels with wear resistant top layer
Loose-laid panels - Multi-layer semi-rigid floor covering (MSF) panels with wear resistant top layer
EN 16511 specifies the characteristics of semi-rigid multilayer modular floor covering with a wear-resistant and decorative surface layer supplied in panels (either tile or plank form). The floor panels are considered suitable for domestic and commercial levels of use and designed for floating installation. This European Standard does not apply to resilient floor panels for loose-laying according to EN 14085, to multilayer wood floorings according to EN 13489, nor to products specified in EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 and ISO 14486. This European Standard applies to areas which are subject to frequent wetting, e.g. bathrooms, laundry rooms or saunas, only if recommended by the producer. This European Standard also includes requirements for marking and packaging.
Lose verlegte Platten - Mehrlagige, halbstarre Bodenbelagsplatten (MSF) mit abriebbeständiger Decklage
Diese Europäische Norm legt die Produkteigenschaften von mehrlagigen, halbstarren Bodenbelagsplatten mit einer abriebbeständigen und dekorativen Decklage (in Fliesen- oder Dielenform) fest. Die Oberfläche sollte nicht von anderen Europäischen Normen, wie z. B. EN ISO 10581, EN ISO 10582, EN ISO 24011 oder EN 12104 erfasst sein. Die Bodenbelagsplatten werden für den Gebrauch im privaten und gewerblichen Bereich als geeignet angesehen.
Diese Europäische Norm gilt nicht für elastische Fußbodenpaneele für lose Verlegung nach EN 14085.
Diese Europäische Norm gilt nicht für Bereiche, die regelmäßig Nässe ausgesetzt sind, wie Badezimmer, Hauswirtschaftsräume, Saunen.
Diese Europäische Norm enthält auch Anforderungen an die Kennzeichnung und Verpackung.
Panneaux pour pose flottante - Panneaux de revêtement de sol multicouches semi-rigides avec couche supérieure résistante à l'usure
La présente Norme européenne spécifie les caractéristiques des revêtements de sol multicouches semi-rigides avec une couche de surface résistante à l'usure et décorative, fournis sous forme de panneaux (dalles ou planches). Il convient que la surface ne soit pas couverte par d'autres Normes produits européennes, par exemple l'EN ISO 10581, l'EN ISO 10582, l'EN ISO 24011 ou l'EN ISO 12104. Ces panneaux de revêtement de sol sont considérés comme étant appropriés à des niveaux d’utilisation domestique et commerciale.
La présente spécification ne s'applique pas aux panneaux de revêtement de sol résilients pour pose flottante conformément à l'EN 14085.
La présente spécification ne s’applique pas aux lieux soumis à une humidification fréquente, comme les salles de bain, les buanderies et les saunas.
La présente norme comprend également des exigences relatives au marquage et à l’emballage.
Prosto položene plošče - Večslojne poltoge talne obloge plošč z odpornim zgornjim delom proti obrabi
EN 16511 določa lastnosti poltogih večplastnih modularnih talnih oblog z dekorativnim zgornjim delom, odpornim proti obrabi, dobavljenih v panelih (v obliki plošč ali trakov). Talne obloge so primerne za domačo in komercialno uporabo ter so zasnovane za plavajočo namestitev. Ta evropski standard ne zajema odpornih talnih panelov za prosto polaganje po standardu EN 14085, večplastnih lesenih oblog po standardu EN 13489 oziroma izdelkov, opisanih v standardih EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 in ISO 14486. Ta evropski standard zajema območja, ki se lahko zmočijo, npr. kopalnice, pralnice ali savne, le če tako priporoči proizvajalec. Ta evropski standard vključuje tudi zahteve za označevanje in pakiranje.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.GSRUQLPLose verlegte Platten - Mehrlagige, halbstarre Bodenbelagsplatten (MSF) mit abriebbeständiger DecklagePanneaux pour pose flottante - Panneaux de revêtement de sol multicouches semi-rigides avec couche supérieure résistante à l'usureLoose-laid panels - Multi-layer semi-rigid floor covering (MSF) panels with wear resistant top layer97.150Netekstilne talne oblogeNon-textile floor coveringsICS:Ta slovenski standard je istoveten z:EN 16511:2014SIST EN 16511:2014en,fr,de01-julij-2014SIST EN 16511:2014SLOVENSKI
STANDARD
SIST EN 16511:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16511
May 2014 ICS 97.150 English Version
Loose-laid panels - Semi-rigid multilayer modular floor covering (MMF) panels with wear resistant top layer
Panneaux pour pose flottante - Panneaux de revêtement de sol semi-rigides, multicouches et modulaires (MMF) avec couche supérieure résistante à l'usure
Paneele für schwimmende Verlegung - Halbstarre, mehrlagige, modulare Fußbodenbeläge (MMF) mit abriebbeständiger Decklage This European Standard was approved by CEN on 28 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16511:2014 ESIST EN 16511:2014
EN 16511:2014 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .5 4 Requirements .5 4.1 General requirements for the panels .5 4.2 Classification requirements .6 5 Marking and packaging .9 5.1 Marking .9 5.2 Packaging .9 Annex A (informative)
Optional properties . 10 Bibliography . 11
SIST EN 16511:2014
EN 16511:2014 (E) 3 Foreword This document (EN 16511:2014) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2014 and conflicting national standards shall be withdrawn at the latest by November 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 16511:2014
EN 16511:2014 (E) 4 1 Scope This European Standard specifies the characteristics of semi-rigid multilayer modular floor covering with a wear-resistant and decorative surface layer supplied in panels (either tile or plank form). The floor panels are considered suitable for domestic and commercial levels of use and designed for floating installation. This European Standard does not apply to resilient floor panels for loose-laying according to EN 14085, to multilayer wood floorings according to EN 13489, nor to products specified in EN ISO 10581, EN ISO 10582, EN ISO 24011, EN 12104 and ISO 14486. This European Standard applies to areas which are subject to frequent wetting, e.g. bathrooms, laundry rooms or saunas, only if recommended by the producer. This European Standard also includes requirements for marking and packaging. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 424, Resilient floor coverings - Determination of the effect of simulated movement of a furniture leg EN 425, Resilient and laminate floor coverings - Castor chair test EN 438-2, High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called Laminates) - Part 2: Determination of properties EN 13329:2006+A1:2008, Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications, requirements and test methods EN 16094, Laminate floor coverings - Test method for the determination of micro-scratch resistance prEN 15468:2013, Laminate floor coverings - Elements with directly applied printing and resin surface layer - Specifications, requirements and test methods EN ISO 10874, Resilient, textile and laminate floor coverings - Classification (ISO 10874) EN ISO 23999, Resilient floor coverings - Determination of dimensional stability and curling after exposure to heat (ISO 23999) EN ISO 24343-1, Resilient and laminate floor coverings - Determination of indentation and residual indentation - Part 1: Residual indentation (ISO 24343-1) ISO 24334, Laminate floor coverings - Determination of locking strength for mechanically assembled panels ISO 24336, Laminate floor co
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.