SIST EN ISO 1234:2001

Split pins (ISO 1234:1997)

Splinte (ISO 1234:1997)

Diese Internationale Norm enthält die Festlegungen über Splinte.

Goupilles fendues (ISO 1234:1997)

La présente Norme internationale prescrit les caractéristiques des goupilles fendues.

Razcepke (ISO 1234:1997)

General Information

• Status: Published
• Publication Date: 30-Jun-2001
• ICS: 21.060.50 - Pins, nails
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jul-2001
• Due Date: 01-Jul-2001
• Completion Date: 01-Jul-2001
• Ref Project: EN ISO 1234:1997 - Split pins (ISO 1234:1997)

Relations

• Replaces: SIST ISO 1234:1995 - Split pins -- Metric series
• Effective Date: 01-Jul-2001

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1234:2001
01-julij-2001
1DGRPHãþD
SIST ISO 1234:1995
Razcepke (ISO 1234:1997)
Split pins (ISO 1234:1997)
Splinte (ISO 1234:1997)
Goupilles fendues (ISO 1234:1997)
Ta slovenski standard je istoveten z: EN ISO 1234:1997
ICS:
21.060.50 =DWLþLåHEOML Pins, nails
SIST EN ISO 1234:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1234:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 1234:2001

---------------------- Page: 3 ----------------------

SIST EN ISO 1234:2001

---------------------- Page: 4 ----------------------

SIST EN ISO 1234:2001
INTERNATIONAL ISO
STANDARD 1234
Second edition
1997-11-01
Split pins
Goupilles fendues
A
Reference number
ISO 1234:1997(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 1234:2001
ISO 1234:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 1234 was prepared by Technical Committee
ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 1234:1976),
which has been technically revised.
©  ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 6 ----------------------

SIST EN ISO 1234:2001
©
INTERNATIONAL STANDARD  ISO ISO 1234:1997(E)
Split pins
1 Scope
This International Standard specifies the characteristics of split pins.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently valid International Standards.
ISO 3269:1988, Fasteners – Acceptance inspection.
1)
ISO 4042:— , Fasteners – Electroplated coatings.
ISO 9717:1990, Phosphate conversion coatings for metals – Method of specifying requirements.
3 Dimensions
See figure 1, table 1 and table 2
Figure 1

1) To be published. (Revision of ISO 4042:1989).
1
...