SIST EN 60297-3-106:2010

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1 (IEC 60297-3-106:2010)

This part of IEC 60297 specifies dimensions for mounting flanges of 19 in subracks or chassis that are to be mounted into metric cabinets or racks. Additional dimensions for subracks or chassis are according to the IEC 60297 series, and for metric cabinets or racks to the IEC 60917 series. EMC, seismic, climatic and environmental requirements and tests, are defined in the IEC 61587 series. The drawings used in this standard are not intended to indicate product design, only the specific dimensions that should be used. The terminology used complies with IEC 60917-1.

Bauweisen für elektronische Einrichtungen - Maße der 482,6-mm-(19-Zoll-)Bauweise - Teil 3-106: Anpassungsmaße für Baugruppenträger und Einschübe, geeignet für metrische Schränke oder Gestelle nach IEC 60917-2-1 (IEC 60297-3-106:2010)

Structures mécaniques pour équipements électroniques - Dimensions des structures mécaniques de la série 482,6 mm (19 pouces) - Partie 3-106: Dimensions d'adaptation des bacs et des châssis, applicables aux baies ou aux bâtis dimensionnés selon le système métrique, conformément à la CEI 60917-2-1 (CEI 60297-3-106:2010)

La CEI 60297-3-106:2010 spécifie les dimensions des brides de montage des bacs ou des châssis de 19 pouces, qui sont destinés à être montés dans des baies ou des bâtis dimensionnés selon le système métrique. Les dimensions supplémentaires des bacs ou des châssis sont conformes à la série CEI 60297 et, pour les baies ou les bâtis dimensionnés selon le système métrique, à la série CEI 60917. Les exigences et les essais de CEM, sismiques, climatiques et environnementaux, sont définis dans la série CEI 61587.

Mehanske strukture za elektronsko opremo - Mere mehanskih struktur serije 482,6 mm (19 inč) - 3-106. del: Prilagoditvene mere za okvire in šasije, uporabne v metričnih ohišjih ali stojalih v skladu z IEC 60917-2-1 (IEC 60297-3-106:2010)

Ta del IEC 60297 določa mere za prirobnice za vgradnjo v 19-inčne okvire in šasije, ki se namestijo v metrična ohišja ali stojala. Dodatne mere za okvire ali šasije so v skladu s serijo IEC 60297 in za metrične kabinete ali stojala v skladu s serijo IEC 60917. V seriji IEC 61587 so opredeljene EMC, seizmične, klimatske in okoljske zahteve in preskusi. Risbe, uporabljene v tem standardu, niso namenjene za prikaz zasnove proizvoda, pač pa le za konkretne mere, ki se morajo uporabiti. Uporabljena terminologija je v skladu z IEC 60917-1.

General Information

• Status: Published
• Publication Date: 03-May-2010
• ICS: 31.240 - Mechanical structures for electronic equipment
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Apr-2010
• Due Date: 18-Jun-2010
• Completion Date: 04-May-2010
• Ref Project: EN 60297-3-106:2010 - Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60297-3-106:2010
01-junij-2010
0HKDQVNHVWUXNWXUH]DHOHNWURQVNRRSUHPR0HUHPHKDQVNLKVWUXNWXUVHULMH
PPLQþGHO3ULODJRGLWYHQHPHUH]DRNYLUHLQãDVLMHXSRUDEQHY
PHWULþQLKRKLãMLKDOLVWRMDOLKYVNODGX],(&,(&
Mechanical structures for electronic equipment - Dimensions of mechanical structures of
the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and
chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1 (IEC
60297-3-106:2010)
Bauweisen für elektronische Einrichtungen - Maße der 482,6-mm-(19-Zoll-)Bauweise -
Teil 3-106: Anpassungsmaße für Baugruppenträger und Einschübe, geeignet für
metrische Schränke oder Gestelle nach IEC 60917-2-1 (IEC 60297-3-106:2010)
Structures mécaniques pour équipements électroniques - Dimensions des structures
mécaniques de la série 482,6 mm (19 pouces) - Partie 3-106: Dimensions d'adaptation
des bacs et des châssis, applicables aux baies ou aux bâtis dimensionnés selon le
système métrique, conformément à la CEI 60917-2-1 (CEI 60297-3-106:2010)
Ta slovenski standard je istoveten z: EN 60297-3-106:2010
ICS:
31.240 Mehanske konstrukcije za Mechanical structures for
elektronsko opremo electronic equipment
SIST EN 60297-3-106:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60297-3-106:2010

---------------------- Page: 2 ----------------------

SIST EN 60297-3-106:2010

EUROPEAN STANDARD
EN 60297-3-106

NORME EUROPÉENNE
April 2010
EUROPÄISCHE NORM

ICS 31.240


English version


Mechanical structures for electronic equipment -
Dimensions of mechanical structures of the 482,6 mm (19 in) series -
Part 3-106: Adaptation dimensions for subracks and chassis applicable
with metric cabinets or racks in accordance with IEC 60917-2-1
(IEC 60297-3-106:2010)


Structures mécaniques pour équipements Bauweisen für elektronische
électroniques - Einrichtungen -
Dimensions des structures mécaniques Maße der 482,6-mm-(19-Zoll-)Bauweise -
de la série 482,6 mm (19 pouces) - Teil 3-106: Adaptionsmaße
Partie 3-106: Dimensions d'adaptation für Baugruppenträger und Einschübe,
des bacs et des châssis, applicables geeignet für metrische Schränke
aux baies ou aux bâtis dimensionnés oder Gestelle nach IEC 60917-2-1
selon le système métrique, conformément (IEC 60297-3-106:2010)
à la CEI 60917-2-1
(CEI 60297-3-106:2010)


This European Standard was approved by CENELEC on 2010-04-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60297-3-106:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60297-3-106:2010
EN 60297-3-106:2010 - 2 -
Foreword
The text of document 48D/419/FDIS, future edition 1 of IEC 60297-3-106, prepared by SC 48D,
Mechanical structures for electronic equipment, of IEC TC 48, Electromechanical components and
mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 60297-3-106 on 2010-04-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-01-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-04-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60297-3-106:2010 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60297-3-100 NOTE  Harmonized as EN 60297-3-100.
IEC 60917-1 NOTE  Harmonized as EN 60917-1.
IEC 60917-2-2 NOTE  Harmonized as EN 60917-2-2
IEC 61587-1 NOTE  Harmonized as EN 61587-1
IEC 61587-2 NOTE  Harmonized as EN 61587-2
IEC 61587-3 NOTE  Harmonized as EN 61587-3
__________

---------------------- Page: 4 ----------------------

SIST EN 60297-3-106:2010
- 3 - EN 60297-3-106:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year


IEC 60297 Series Mechanical structures for electronic EN 60297 Series
equipment - Dimensions of mechanical
structures of the 482,6 mm (19 in) series


IEC 60297-3-101 - Mechanical structures for electronic EN 60297-3-101 -
equipment - Dimensions of mechanical
structures of the 482,6 mm (19 in) series -
Part 3-101: Subracks and associated plug-in
units



IEC 60917 Series Modular order for the development of EN 60917 Series
mechanical structures for electronic
equipment practices


IEC 60917-2-1 - Modular order for the development of EN 60917-2-1 -
mechanical structures for electronic
equipment practices -
Part 2: Sectional specification - Interface co-
ordination dimensions for the 25 mm
equipment practice -
Section 1: Detail specification - Dimensions
for cabinets and racks


IEC 60917-2-4 - Modular order for the development of EN 60917-2-4 -
mechanical structures for electronic
equipment practices -
Part 2-4: Sectional specification - Interface co-
ordination dimensions for the 25 mm
equipment practice - Adaptation dimensions
for subracks or chassis applicable in cabinets
or racks in accordance with IEC 60297-3-100
(19 in)

---------------------- Page: 5 ----------------------

SIST EN 60297-3-106:2010

---------------------- Page: 6 ----------------------

SIST EN 60297-3-106:2010

IEC 60297-3-106
®
Edition 1.0 2010-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside


Mechanical structures for electronic equipment – Dimensions of mechanical
structures of the 482, 6 mm (19 in) series –
Part 3-106: Adaptation dimensions for subracks and chassis applicable to metric
cabinets or racks in accordance with IEC 60917-2-1

Structures mécaniques pour équipements électroniques – Dimensions des
structures mécaniques de la série 482,6 mm (19 pouces) –
Partie 3-106: Dimensions d’adaptation des bacs et des châssis, applicables aux
baies ou aux bâtis dimensionnés selon le système métrique, conformément à la
CEI 60917-2-1

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
P
CODE PRIX
ICS 31.240 ISBN 2-8318-1084-1
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60297-3-106:2010
– 2 – 60297-3-106 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope and object.6
2 Normative references .6
3 Arrangement overview (Figure 1) and definitions .6
4 Dimensions for flanges of 19 in subracks or chassis applicable for mounting on
metric cabinets or racks.7
4.1 General .7
4.2 Dimensions for mounting holes arrangements on the flanges, mounting-
layout referred to the pitch lines of the 19 in subracks, or chassis .7
4.3 Dimensions for mounting holes arrangements on the flanges, mounting
layout referred to the unit centre lines of the 19 in subracks or chassis .10
4.4 Dimensions for flanges of 19 in subracks applicable for metric cabinets or
racks with 515 mm mounting hole dimension.13
Bibliography.15

Figure 1 – Arrangement overview – Adaptation of subracks of the IEC 60297-3-101
series into cabinets of the IEC 60917-2-1 series .7
Figure 2 – Mounting hole arrangements on the flanges, mounting layout referred to
the bottom pitch lines of the 19 in subracks or chassis.8
Figure 3 – Dimensions of mounting hole positions of the flanges, mounting layout
referred to the bottom pitch lines of the 19 in subracks or chassis .9
Figure 4 – Mounting hole arrangements on the flanges, mounting layout referred to
the unit centre lines of the 19 in subracks or chassis .11
Figure 5 – Dimensions of mounting holes positions of the flanges, mounting layout
referred to the unit centre lines of the 19 in subracks or chassis .12
Figure 6 – Dimensions for flanges of 19 in subracks that are applicable for metric
cabinets with 515 mm mounting hole dimension.14

Table 1 – Dimensions of mounting holes positions of the flange, mounting layout
referred to the bottom pitch lines of the 19 in subracks or chassis .10
Table 2 – Dimensions of mounting holes positions of the flange, mounting layout
referred to the unit centre lines of the 19 in subracks or chassis .13

---------------------- Page: 8 ----------------------

SIST EN 60297-3-106:2010
60297-3-106 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT –
DIMENSIONS OF MECHANICAL STRUCTURES
OF THE 482, 6 mm (19 in) SERIES –

Part 3-106: Adaptation dimensions for subracks and chassis applicable
to metric cabinets or racks in accordance with IEC 60917-2-1


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC mark
...