SIST EN 301 908-15 V15.1.1:2020
(Main)IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 15: Evolved Universal Terrestrial Radio Access (E-UTRA FDD) Repeaters
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 15: Evolved Universal Terrestrial Radio Access (E-UTRA FDD) Repeaters
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
The present document covers requirements for E-UTRA Repeaters for 3GPP Release 15. NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive 2014/53/EU [i.1] is given in annex A.
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra - 15. del: Ponavljalniki za razviti prizemni radijski dostop za UMTS (E-UTRA FDD)
Ta dokument se uporablja za radijsko opremo naslednje vrste:
• ponavljalniki za razviti prizemni radijski dostop za UMTS (E-UTRA) (FDD).
Ta vrsta radijske opreme lahko deluje v vseh delih operativnih pasov iz preglednice 1-1.
Preglednica 1-1: Pasovi, v katerih delujejo ponavljalniki E-UTRA
Ta dokument zajema zahteve za ponavljalnike E-UTRA za izdajo 15 dokumenta 3GPP. OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.1] je podano v dodatku A.
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 301 908-15 V15.1.1:2020
01-marec-2020
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra -
15. del: Ponavljalniki za razviti prizemni radijski dostop za UMTS (E-UTRA FDD)
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 15:
Evolved Universal Terrestrial Radio Access (E-UTRA FDD) Repeaters
Ta slovenski standard je istoveten z: ETSI EN 301 908-15 V15.1.1 (2020-01)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.99 Druge mobilne storitve Other mobile services
SIST EN 301 908-15 V15.1.1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 301 908-15 V15.1.1:2020
---------------------- Page: 2 ----------------------
SIST EN 301 908-15 V15.1.1:2020
ETSI EN 301 908-15 V15.1.1 (2020-01)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 15: Evolved Universal Terrestrial Radio Access
(E-UTRA FDD) Repeaters
---------------------- Page: 3 ----------------------
SIST EN 301 908-15 V15.1.1:2020
2 ETSI EN 301 908-15 V15.1.1 (2020-01)
Reference
REN/MSG-TFES-15-15
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, LTE, mobile, radio, regulation,
repeater, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 908-15 V15.1.1:2020
3 ETSI EN 301 908-15 V15.1.1 (2020-01)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Operating band unwanted emissions . 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 12
4.2.2.2.0 General . 12
4.2.2.2.1 General operating band unwanted emissions . 12
4.2.2.2.2 Protection of the BS receiver in the operating band . 16
4.2.2.2.3 Co-existence with services in adjacent frequency bands . 16
4.2.2.2.4 Additional for protection of DTT . 17
4.2.2.2.5 Additional limits for operation in Band 32 . 17
4.2.2.3 Conformance . 17
4.2.3 Spurious emissions . 17
4.2.3.1 Definition . 17
4.2.3.2 Limit . 17
4.2.3.2.0 General . 17
4.2.3.2.1 Spurious emissions . 18
4.2.3.2.2 Co-existence with other systems in the same geographical area . 18
4.2.3.3 Conformance . 19
4.2.4 Maximum output power . 20
4.2.4.1 Definition . 20
4.2.4.2 Limit . 20
4.2.4.3 Conformance . 20
4.2.5 Input intermodulation . 20
4.2.5.1 Definition . 20
4.2.5.2 Limit . 21
4.2.5.2.1 General input intermodulation requirement . 21
4.2.5.2.2 Co-existence with other systems . 21
4.2.5.3 Conformance . 22
4.2.6 Out of band gain . 22
4.2.6.1 Definition . 22
4.2.6.2 Limits . 22
4.2.6.3 Conformance . 23
4.2.7 Adjacent Channel Rejection Ratio . 23
4.2.7.1 Definition . 23
4.2.7.2 Limit . 23
4.2.7.2.1 ACRR . 23
4.2.7.2.2 Co-existence with UTRA . 23
4.2.7.3 Conformance . 24
4.2.8 Output intermodulation . 24
ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 908-15 V15.1.1:2020
4 ETSI EN 301 908-15 V15.1.1 (2020-01)
4.2.8.1 Definition . 24
4.2.8.2 Limit . 24
4.2.8.3 Conformance . 24
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 Interpretation of the measurement results . 25
5.3 Essential radio test suites . 25
5.3.0 Introduction. 25
5.3.1 Operating band unwanted emissions . 25
5.3.1.1 Initial conditions . 25
5.3.1.2 Procedures . 26
5.3.1.3 Test requirement . 26
5.3.2 Spurious emissions . 26
5.3.2.1 Initial conditions . 26
5.3.2.2 Procedures . 27
5.3.2.3 Test requirement . 27
5.3.3 Maximum output power . 27
5.3.3.1 Initial conditions . 27
5.3.3.2 Procedures . 28
5.3.3.3 Test requirement . 28
5.3.4 Input intermodulation . 28
5.3.4.1 Initial conditions . 28
5.3.4.2 Procedures . 28
5.3.4.3 Test requirement . 29
5.3.5 Out of band gain . 29
5.3.5.1 Initial conditions . 29
5.3.5.2 Procedures . 29
5.3.5.3 Test requirement . 29
5.3.6 Adjacent Channel Rejection Ratio . 29
5.3.6.1 Initial conditions . 29
5.3.6.2 Procedures . 30
5.3.6.3 Test requirement . 30
5.3.7 Output intermodulation . 30
5.3.7.1 Initial conditions . 30
5.3.7.2 Procedures . 30
5.3.7.3 Test requirement . 31
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Repeater configurations . 33
B.1 Power supply . 33
B.2 Power supply options . 33
B.3 Combining of Repeaters . 33
Annex C (normative): Repeater stimulus signal spectral purity requirements . 34
Annex D (informative): Recommended maximum measurement uncertainty . 35
Annex E (informative): Bibliography . 37
Annex F (informative): Change history . 38
History . 39
ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 908-15 V15.1.1:2020
5 ETSI EN 301 908-15 V15.1.1 (2020-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.8] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 15 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.3].
National transposition dates
Date of adoption of this EN: 16 December 2019
Date of latest announcement of this EN (doa): 31 March 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 September 2020
Date of withdrawal of any conflicting National Standard (dow): 30 September 2021
ETSI
---------------------- Page: 7 ----------------------
SIST EN 301 908-15 V15.1.1:2020
6 ETSI EN 301 908-15 V15.1.1 (2020-01)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive [i.1]. The present document is produced
following the guidance in ETSI EG 203 336 [i.2] as applicable.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 301 908-15 V15.1.1:2020
7 ETSI EN 301 908-15 V15.1.1 (2020-01)
1 Scope
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
E-UTRA FDD Direction of transmission E-UTRA Repeater operating bands
band
1 Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
3 Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
7 Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
8 Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz
20 Downlink 791 MHz to 821 MHz
Uplink 832 MHz to 862 MHz
22 Downlink 3 510 MHz to 3 590 MHz
Uplink 3 410 MHz to 3 490 MHz
28 Downlink 758 MHz to 803 MHz
Uplink 703 MHz to 748 MHz
31 Downlink 462,5 MHz to 467,5 MHz
Uplink 452,5 MHz to 457,5 MHz
32 Downlink 1 452 MHz to 1 496 MHz
(note 1) Uplink N/A
(note 2)
72 Downlink 461 MHz to 466 MHz
Uplink 451 MHz to 456 MHz
NOTE 1: Restricted to E-UTRA operation when carrier aggregation is configured. The downlink operating
band is paired with the uplink operating band (external) of the carrier aggregation configuration
that is supporting the configured Pcell.
NOTE 2: Radio equipment in band 32 is only allowed to operate between 1 452 MHz and 1 492 MHz.
The present document covers requirements for E-UTRA Repeaters for 3GPP Release 15.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 136 143 (V15.0.0) (09-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 15.0.0 Release 15)".
ETSI
---------------------- Page: 9 ----------------------
SIST EN 301 908-15 V15.1.1:2020
8 ETSI EN 301 908-15 V15.1.1 (2020-01)
[2] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[3] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[4] ETSI TS 136 141 (V15.3.0) (07-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 15.3.0 Release 15)".
[5] ETSI TS 125 141 (V15.3.0) (07-2018): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 15.3.0 Release 15)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised
Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".
[i.3] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
[i.4] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.5] Void.
[i.6] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain".
[i.7] ETSI EN 301 908-11 (V11.1.2): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread
(UTRA FDD) Repeaters".
[i.8] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
carrier: modulated waveform conveying the E-UTRA or UTRA (WCDMA) physical channels
ETSI
---------------------- Page: 10 ----------------------
SIST EN 301 908-15 V15.1.1:2020
9 ETSI EN 301 908-15 V15.1.1 (2020-01)
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
channel edge: lowest and highest frequency of the E-UTRA carrier, separated by the channel bandwidth
donor coupling loss: coupling loss between the repeater and the donor Base Station
downlink: signal path where Base Station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink
nominal passband edge: lowest and highest frequency of the pass band of the repeater
operating band: frequency range that is defined with a specific set of technical requirements, in which E-UTRA FDD
opera
...
ETSI EN 301 908-15 V15.1.1 (2020-01)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 15: Evolved Universal Terrestrial Radio Access
(E-UTRA FDD) Repeaters
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-15 V15.1.1 (2020-01)
Reference
REN/MSG-TFES-15-15
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, LTE, mobile, radio, regulation,
repeater, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-15 V15.1.1 (2020-01)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Operating band unwanted emissions . 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 12
4.2.2.2.0 General . 12
4.2.2.2.1 General operating band unwanted emissions . 12
4.2.2.2.2 Protection of the BS receiver in the operating band . 16
4.2.2.2.3 Co-existence with services in adjacent frequency bands . 16
4.2.2.2.4 Additional for protection of DTT . 17
4.2.2.2.5 Additional limits for operation in Band 32 . 17
4.2.2.3 Conformance . 17
4.2.3 Spurious emissions . 17
4.2.3.1 Definition . 17
4.2.3.2 Limit . 17
4.2.3.2.0 General . 17
4.2.3.2.1 Spurious emissions . 18
4.2.3.2.2 Co-existence with other systems in the same geographical area . 18
4.2.3.3 Conformance . 19
4.2.4 Maximum output power . 20
4.2.4.1 Definition . 20
4.2.4.2 Limit . 20
4.2.4.3 Conformance . 20
4.2.5 Input intermodulation . 20
4.2.5.1 Definition . 20
4.2.5.2 Limit . 21
4.2.5.2.1 General input intermodulation requirement . 21
4.2.5.2.2 Co-existence with other systems . 21
4.2.5.3 Conformance . 22
4.2.6 Out of band gain . 22
4.2.6.1 Definition . 22
4.2.6.2 Limits . 22
4.2.6.3 Conformance . 23
4.2.7 Adjacent Channel Rejection Ratio . 23
4.2.7.1 Definition . 23
4.2.7.2 Limit . 23
4.2.7.2.1 ACRR . 23
4.2.7.2.2 Co-existence with UTRA . 23
4.2.7.3 Conformance . 24
4.2.8 Output intermodulation . 24
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-15 V15.1.1 (2020-01)
4.2.8.1 Definition . 24
4.2.8.2 Limit . 24
4.2.8.3 Conformance . 24
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 Interpretation of the measurement results . 25
5.3 Essential radio test suites . 25
5.3.0 Introduction. 25
5.3.1 Operating band unwanted emissions . 25
5.3.1.1 Initial conditions . 25
5.3.1.2 Procedures . 26
5.3.1.3 Test requirement . 26
5.3.2 Spurious emissions . 26
5.3.2.1 Initial conditions . 26
5.3.2.2 Procedures . 27
5.3.2.3 Test requirement . 27
5.3.3 Maximum output power . 27
5.3.3.1 Initial conditions . 27
5.3.3.2 Procedures . 28
5.3.3.3 Test requirement . 28
5.3.4 Input intermodulation . 28
5.3.4.1 Initial conditions . 28
5.3.4.2 Procedures . 28
5.3.4.3 Test requirement . 29
5.3.5 Out of band gain . 29
5.3.5.1 Initial conditions . 29
5.3.5.2 Procedures . 29
5.3.5.3 Test requirement . 29
5.3.6 Adjacent Channel Rejection Ratio . 29
5.3.6.1 Initial conditions . 29
5.3.6.2 Procedures . 30
5.3.6.3 Test requirement . 30
5.3.7 Output intermodulation . 30
5.3.7.1 Initial conditions . 30
5.3.7.2 Procedures . 30
5.3.7.3 Test requirement . 31
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Repeater configurations . 33
B.1 Power supply . 33
B.2 Power supply options . 33
B.3 Combining of Repeaters . 33
Annex C (normative): Repeater stimulus signal spectral purity requirements . 34
Annex D (informative): Recommended maximum measurement uncertainty . 35
Annex E (informative): Bibliography . 37
Annex F (informative): Change history . 38
History . 39
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-15 V15.1.1 (2020-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.8] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 15 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.3].
National transposition dates
Date of adoption of this EN: 16 December 2019
Date of latest announcement of this EN (doa): 31 March 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 September 2020
Date of withdrawal of any conflicting National Standard (dow): 30 September 2021
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-15 V15.1.1 (2020-01)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive [i.1]. The present document is produced
following the guidance in ETSI EG 203 336 [i.2] as applicable.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-15 V15.1.1 (2020-01)
1 Scope
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
E-UTRA FDD Direction of transmission E-UTRA Repeater operating bands
band
1 Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
3 Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
7 Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
8 Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz
20 Downlink 791 MHz to 821 MHz
Uplink 832 MHz to 862 MHz
22 Downlink 3 510 MHz to 3 590 MHz
Uplink 3 410 MHz to 3 490 MHz
28 Downlink 758 MHz to 803 MHz
Uplink 703 MHz to 748 MHz
31 Downlink 462,5 MHz to 467,5 MHz
Uplink 452,5 MHz to 457,5 MHz
32 Downlink 1 452 MHz to 1 496 MHz
(note 1) Uplink N/A
(note 2)
72 Downlink 461 MHz to 466 MHz
Uplink 451 MHz to 456 MHz
NOTE 1: Restricted to E-UTRA operation when carrier aggregation is configured. The downlink operating
band is paired with the uplink operating band (external) of the carrier aggregation configuration
that is supporting the configured Pcell.
NOTE 2: Radio equipment in band 32 is only allowed to operate between 1 452 MHz and 1 492 MHz.
The present document covers requirements for E-UTRA Repeaters for 3GPP Release 15.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 136 143 (V15.0.0) (09-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 15.0.0 Release 15)".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-15 V15.1.1 (2020-01)
[2] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[3] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[4] ETSI TS 136 141 (V15.3.0) (07-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 15.3.0 Release 15)".
[5] ETSI TS 125 141 (V15.3.0) (07-2018): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 15.3.0 Release 15)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised
Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".
[i.3] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
[i.4] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.5] Void.
[i.6] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain".
[i.7] ETSI EN 301 908-11 (V11.1.2): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread
(UTRA FDD) Repeaters".
[i.8] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
carrier: modulated waveform conveying the E-UTRA or UTRA (WCDMA) physical channels
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 908-15 V15.1.1 (2020-01)
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
channel edge: lowest and highest frequency of the E-UTRA carrier, separated by the channel bandwidth
donor coupling loss: coupling loss between the repeater and the donor Base Station
downlink: signal path where Base Station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink
nominal passband edge: lowest and highest frequency of the pass band of the repeater
operating band: frequency range that is defined with a specific set of technical requirements, in which E-UTRA FDD
operates
NOTE: The operating band(s) for an E-UTRA Repeater is declared by the manufacturer according to the
designations in clause 1, table 1-1. Operating bands for UTRA are designated with Roman numerals,
while the corresponding operating bands for E-UTRA are designated with Arabic numerals. Unless
specified, operating band refers to the uplink operating band and downlink operating band.
output power, Pout: mean power of one carrier at maximum repeater gain delivered to a load with resistance equal to
the nominal load impedance of the transmitter
pass band: frequency range that the repeater operates in with operational configuration
NOTE: This frequency range can correspond to one or several consecutive channels. If they are not consecutive
each subset of channels is considered as an individual pass band. The Repeater can have one or several
pass bands.
rated output power: rated output power of the repeater is the mean power level per carrier that the manufacturer has
declared to be available at the antenna connector
repeater: device that receives, amplifies and transmits the radiated or conducted RF carrier both in the downlink
direction (from the Base Station to the mobile
...
Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 15: Evolved Universal Terrestrial Radio Access
(E-UTRA FDD) Repeaters
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Reference
REN/MSG-TFES-15-15
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, LTE, mobile, radio, regulation,
repeater, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Operating band unwanted emissions . 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 12
4.2.2.2.0 General . 12
4.2.2.2.1 General operating band unwanted emissions . 12
4.2.2.2.2 Protection of the BS receiver in the operating band . 16
4.2.2.2.3 Co-existence with services in adjacent frequency bands . 16
4.2.2.2.4 Additional for protection of DTT . 17
4.2.2.2.5 Additional limits for operation in Band 32 . 17
4.2.2.3 Conformance . 17
4.2.3 Spurious emissions . 17
4.2.3.1 Definition . 17
4.2.3.2 Limit . 17
4.2.3.2.0 General . 17
4.2.3.2.1 Spurious emissions . 18
4.2.3.2.2 Co-existence with other systems in the same geographical area . 18
4.2.3.3 Conformance . 19
4.2.4 Maximum output power . 20
4.2.4.1 Definition . 20
4.2.4.2 Limit . 20
4.2.4.3 Conformance . 20
4.2.5 Input intermodulation . 20
4.2.5.1 Definition . 20
4.2.5.2 Limit . 21
4.2.5.2.1 General input intermodulation requirement . 21
4.2.5.2.2 Co-existence with other systems . 21
4.2.5.3 Conformance . 22
4.2.6 Out of band gain . 22
4.2.6.1 Definition . 22
4.2.6.2 Limits . 22
4.2.6.3 Conformance . 23
4.2.7 Adjacent Channel Rejection Ratio . 23
4.2.7.1 Definition . 23
4.2.7.2 Limit . 23
4.2.7.2.1 ACRR . 23
4.2.7.2.2 Co-existence with UTRA . 23
4.2.7.3 Conformance . 24
4.2.8 Output intermodulation . 24
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
4.2.8.1 Definition . 24
4.2.8.2 Limit . 24
4.2.8.3 Conformance . 24
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 Interpretation of the measurement results . 25
5.3 Essential radio test suites . 25
5.3.0 Introduction. 25
5.3.1 Operating band unwanted emissions . 25
5.3.1.1 Initial conditions . 25
5.3.1.2 Procedures . 26
5.3.1.3 Test requirement . 26
5.3.2 Spurious emissions . 26
5.3.2.1 Initial conditions . 26
5.3.2.2 Procedures . 27
5.3.2.3 Test requirement . 27
5.3.3 Maximum output power . 27
5.3.3.1 Initial conditions . 27
5.3.3.2 Procedures . 28
5.3.3.3 Test requirement . 28
5.3.4 Input intermodulation . 28
5.3.4.1 Initial conditions . 28
5.3.4.2 Procedures . 28
5.3.4.3 Test requirement . 29
5.3.5 Out of band gain . 29
5.3.5.1 Initial conditions . 29
5.3.5.2 Procedures . 29
5.3.5.3 Test requirement . 29
5.3.6 Adjacent Channel Rejection Ratio . 29
5.3.6.1 Initial conditions . 29
5.3.6.2 Procedures . 30
5.3.6.3 Test requirement . 30
5.3.7 Output intermodulation . 30
5.3.7.1 Initial conditions . 30
5.3.7.2 Procedures . 30
5.3.7.3 Test requirement . 31
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Repeater configurations . 33
B.1 Power supply . 33
B.2 Power supply options . 33
B.3 Combining of Repeaters . 33
Annex C (normative): Repeater stimulus signal spectral purity requirements . 34
Annex D (informative): Recommended maximum measurement uncertainty . 35
Annex E (informative): Bibliography . 37
Annex F (informative): Change history . 38
History . 39
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards
Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.8] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 15 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.3].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive [i.1]. The present document is produced
following the guidance in ETSI EG 203 336 [i.2] as applicable.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
1 Scope
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
E-UTRA FDD Direction of transmission E-UTRA Repeater operating bands
band
1 Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
3 Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
7 Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
8 Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz
20 Downlink 791 MHz to 821 MHz
Uplink 832 MHz to 862 MHz
22 Downlink 3 510 MHz to 3 590 MHz
Uplink 3 410 MHz to 3 490 MHz
28 Downlink 758 MHz to 803 MHz
Uplink 703 MHz to 748 MHz
31 Downlink 462,5 MHz to 467,5 MHz
Uplink 452,5 MHz to 457,5 MHz
32 Downlink 1 452 MHz to 1 496 MHz
(note 1) Uplink N/A
(note 2)
72 Downlink 461 MHz to 466 MHz
Uplink 451 MHz to 456 MHz
NOTE 1: Restricted to E-UTRA operation when carrier aggregation is configured. The downlink operating
band is paired with the uplink operating band (external) of the carrier aggregation configuration
that is supporting the configured Pcell.
NOTE 2: Radio equipment in band 32 is only allowed to operate between 1 452 MHz and 1 492 MHz.
The present document covers requirements for E-UTRA Repeaters for 3GPP Release 15.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 136 143 (V15.0.0) (09-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 15.0.0 Release 15)".
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
[2] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[3] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[4] ETSI TS 136 141 (V15.3.0) (07-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 15.3.0 Release 15)".
[5] ETSI TS 125 141 (V15.3.0) (07-2018): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 15.3.0 Release 15)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised
Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".
[i.3] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
[i.4] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.5] Void.
[i.6] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain".
[i.7] ETSI EN 301 908-11 (V11.1.2): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread
(UTRA FDD) Repeaters".
[i.8] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
carrier: modulated waveform conveying the E-UTRA or UTRA (WCDMA) physical channels
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
channel edge: lowest and highest frequency of the E-UTRA carrier, separated by the channel bandwidth
donor coupling loss: coupling loss between the repeater and the donor Base Station
downlink: signal path where Base Station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink
nominal passband edge: lowest and highest frequency of the pass band of the repeater
operating band: frequency range that is defined with a specific set of technical requirements, in which E-UTRA FDD
operates
NOTE: The operating band(s) for an E-UTRA Repeater is declared by the manufacturer according to the
designations in clause 1, table 1-1. Operating bands for UTRA are designated with Roman numerals,
while the corresponding operating bands for E-UTRA are designated with Arabic numerals. Unless
specified, operating band refers to the uplink operating band and downlink operating band.
output power, Pout: mean power of one carrier at maximum repeater gain delivered to a load with resistance equal to
the nominal load impedance of the transmitter
pass band: frequency range that the repeater operates in with operational configuration
NOTE: This frequency range can correspond to one or several consecutive channels. If they are not consecutive
each subset of channels is considered as an individual pass band. The Repeater can have one or several
pass bands.
rated output power: rated output power of the repeater is the mean power level per carrier that the manufacturer has
declared to be available at the antenna connector
repeater: devic
...
SLOVENSKI STANDARD
oSIST prEN 301 908-15 V15.0.1:2019
01-november-2019
Celična omrežja IMT - Harmonizirani standard za dostop do radijskega spektra -
15. del: Ponavljalniki za razviti prizemni radijski dostop za UMTS (E-UTRA FDD)
IMT cellular networks - Harmonised Standard for access to radio spectrum - Part 15:
Evolved Universal Terrestrial Radio Access (E-UTRA FDD) Repeaters
Ta slovenski standard je istoveten z: ETSI EN 301 908-15 V15.0.1 (2019-09)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.99 Druge mobilne storitve Other mobile services
oSIST prEN 301 908-15 V15.0.1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
---------------------- Page: 2 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard for access to radio spectrum;
Part 15: Evolved Universal Terrestrial Radio Access
(E-UTRA FDD) Repeaters
---------------------- Page: 3 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
2 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Reference
REN/MSG-TFES-15-15
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, LTE, mobile, radio, regulation,
repeater, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
3 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Operating band unwanted emissions . 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 12
4.2.2.2.0 General . 12
4.2.2.2.1 General operating band unwanted emissions . 12
4.2.2.2.2 Protection of the BS receiver in the operating band . 16
4.2.2.2.3 Co-existence with services in adjacent frequency bands . 16
4.2.2.2.4 Additional for protection of DTT . 17
4.2.2.2.5 Additional limits for operation in Band 32 . 17
4.2.2.3 Conformance . 17
4.2.3 Spurious emissions . 17
4.2.3.1 Definition . 17
4.2.3.2 Limit . 17
4.2.3.2.0 General . 17
4.2.3.2.1 Spurious emissions . 18
4.2.3.2.2 Co-existence with other systems in the same geographical area . 18
4.2.3.3 Conformance . 19
4.2.4 Maximum output power . 20
4.2.4.1 Definition . 20
4.2.4.2 Limit . 20
4.2.4.3 Conformance . 20
4.2.5 Input intermodulation . 20
4.2.5.1 Definition . 20
4.2.5.2 Limit . 21
4.2.5.2.1 General input intermodulation requirement . 21
4.2.5.2.2 Co-existence with other systems . 21
4.2.5.3 Conformance . 22
4.2.6 Out of band gain . 22
4.2.6.1 Definition . 22
4.2.6.2 Limits . 22
4.2.6.3 Conformance . 23
4.2.7 Adjacent Channel Rejection Ratio . 23
4.2.7.1 Definition . 23
4.2.7.2 Limit . 23
4.2.7.2.1 ACRR . 23
4.2.7.2.2 Co-existence with UTRA . 23
4.2.7.3 Conformance . 24
4.2.8 Output intermodulation . 24
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
4 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
4.2.8.1 Definition . 24
4.2.8.2 Limit . 24
4.2.8.3 Conformance . 24
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 Interpretation of the measurement results . 25
5.3 Essential radio test suites . 25
5.3.0 Introduction. 25
5.3.1 Operating band unwanted emissions . 25
5.3.1.1 Initial conditions . 25
5.3.1.2 Procedures . 26
5.3.1.3 Test requirement . 26
5.3.2 Spurious emissions . 26
5.3.2.1 Initial conditions . 26
5.3.2.2 Procedures . 27
5.3.2.3 Test requirement . 27
5.3.3 Maximum output power . 27
5.3.3.1 Initial conditions . 27
5.3.3.2 Procedures . 28
5.3.3.3 Test requirement . 28
5.3.4 Input intermodulation . 28
5.3.4.1 Initial conditions . 28
5.3.4.2 Procedures . 28
5.3.4.3 Test requirement . 29
5.3.5 Out of band gain . 29
5.3.5.1 Initial conditions . 29
5.3.5.2 Procedures . 29
5.3.5.3 Test requirement . 29
5.3.6 Adjacent Channel Rejection Ratio . 29
5.3.6.1 Initial conditions . 29
5.3.6.2 Procedures . 30
5.3.6.3 Test requirement . 30
5.3.7 Output intermodulation . 30
5.3.7.1 Initial conditions . 30
5.3.7.2 Procedures . 30
5.3.7.3 Test requirement . 31
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Repeater configurations . 33
B.1 Power supply . 33
B.2 Power supply options . 33
B.3 Combining of Repeaters . 33
Annex C (normative): Repeater stimulus signal spectral purity requirements . 34
Annex D (informative): Recommended maximum measurement uncertainty . 35
Annex E (informative): Bibliography . 37
Annex F (informative): Change history . 38
History . 39
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
5 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards
Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.8] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 15 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.3].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
6 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive [i.1]. The present document is produced
following the guidance in ETSI EG 203 336 [i.2] as applicable.
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
7 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
1 Scope
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
E-UTRA FDD Direction of transmission E-UTRA Repeater operating bands
band
1 Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
3 Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
7 Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
8 Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz
20 Downlink 791 MHz to 821 MHz
Uplink 832 MHz to 862 MHz
22 Downlink 3 510 MHz to 3 590 MHz
Uplink 3 410 MHz to 3 490 MHz
28 Downlink 758 MHz to 803 MHz
Uplink 703 MHz to 748 MHz
31 Downlink 462,5 MHz to 467,5 MHz
Uplink 452,5 MHz to 457,5 MHz
32 Downlink 1 452 MHz to 1 496 MHz
(note 1) Uplink N/A
(note 2)
72 Downlink 461 MHz to 466 MHz
Uplink 451 MHz to 456 MHz
NOTE 1: Restricted to E-UTRA operation when carrier aggregation is configured. The downlink operating
band is paired with the uplink operating band (external) of the carrier aggregation configuration
that is supporting the configured Pcell.
NOTE 2: Radio equipment in band 32 is only allowed to operate between 1 452 MHz and 1 492 MHz.
The present document covers requirements for E-UTRA Repeaters for 3GPP Release 15.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 136 143 (V15.0.0) (09-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); FDD repeater conformance testing (3GPP TS 36.143 version 15.0.0 Release 15)".
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
8 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
[2] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[3] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[4] ETSI TS 136 141 (V15.3.0) (07-2018): "LTE; Evolved Universal Terrestrial Radio Access
(E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 15.3.0 Release 15)".
[5] ETSI TS 125 141 (V15.3.0) (07-2018): "Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 15.3.0 Release 15)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised
Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".
[i.3] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirements".
[i.4] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.5] Void.
[i.6] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain".
[i.7] ETSI EN 301 908-11 (V11.1.2): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread
(UTRA FDD) Repeaters".
[i.8] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
carrier: modulated waveform conveying the E-UTRA or UTRA (WCDMA) physical channels
ETSI
---------------------- Page: 10 ----------------------
oSIST prEN 301 908-15 V15.0.1:2019
9 Draft ETSI EN 301 908-15 V15.0.1 (2019-09)
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
channel edge: lowest and highest frequency of the E-UTRA carrier, separated by the channel bandwidth
donor coupling loss: coupling loss between the repeater and the donor Base Station
downlink: signal path where Base Station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink
nominal passband edge
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.