Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 6: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive

The present document applies to the following radio equipment type:
User equipment for IMT-2000 CDMA TDD (UTRA TDD and E-UTRA TDD).
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.
  The UTRA TDD component of IMT-2000 CDMA TDD supports three options of the TDD mode with the chip rates of 3,84 Mcps, 7,68Mcps and 1,28 Mcps. These three options are called the 3,84 Mcps TDD option, the 1,28 Mcps TDD option and the 7,68 Mcps TDD option respectively. The requirements are listed in different clauses only if the parameters deviate. The present document covers requirements for:
3,84 Mcps UTRA TDD option user equipment for Release 99, 4, 5, 6, 7 and 8;
1,28 Mcps UTRA TDD option user equipment for Release 4, 5, 6, 7 and 8;
7,68 Mcps UTRA TDD option user equipment for Release 7 and 8;
E-UTRA TDD user equipment for Release 8.
The present document covers the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document.

Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Bazne postaje (BS), ponavljalniki (repetitorji) in uporabniška oprema (UE) za celična omrežja tretje generacije IMT-2000 - 6. del: Harmonizirani EN za IMT-2000, CDMA TDD (UTRA TDD in E-UTRA TDD) (UE), ki zajema bistvene zahteve člena 3.2 direktive R&TTE

Pričujoči dokument velja za naslednjo vrsto radijske opreme:
uporabniško opremo za IMT-2000 CDMA TDD (UTRA TDD in E-UTRA TDD).
Ta vrsta radijske opreme je zmožna delovanja v vseh ali katerem koli delu frekvenčnega pasu, kot so navedeni v tabeli 1-1.
UTRA TDD komponenta IMT-2000 CDMA TDD podpira tri možnosti TDD načina s številom pulzov kode 3,84Mcps, 7,68 Mcps in 1,28 Mcps. Te tri možnosti so imenovane 3,84 Mcps TDD možnost, 1,28 Mcps TDD možnost in 7,68 Mcps TDD možnost v tem vrstnem redu. Zahteve so navedene v različnih klavzulah, če parametri odstopajo. Pričujoči dokument zajema zahteve za:
uporabniško opremo 3,84 Mcps UTRA TDD možnost za izdajo 99, 4, 5, 6, 7 in 8;
uporabniško opremo 1,28 Mcps UTRA TDD možnost za izdajo 4, 5, 6, 7 in 8;
uporabniško opremo 7,68 Mcps UTRA TDD možnost za izdajo 7 in 8;
uporabniško opremo E-UTRA TDD za izdajo 8.
Pričujoči dokument zajema določbe Direktive 1999/5/ES [i.2] (direktive R&TTE), člena 3.2, ki navaja, da » … je radijska oprema narejena tako, da učinkovito izrablja spekter, razporejen za prizemne/vesoljske radiokomunikacije in orbitalne vire, tako da ne pride do škodljivega motenja«. Poleg pričujočega dokumenta, se ostali EN, ki določajo tehnične zahteve v skladu z bistvenimi zahtevami v drugih delih člena 3 direktive R&TTE [i.2], lahko uporabljajo za opremo znotraj področja uporabe pričujočega dokumenta.

General Information

Status
Published
Public Enquiry End Date
31-Jul-2009
Publication Date
08-Apr-2010
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
18-Mar-2010
Due Date
23-May-2010
Completion Date
09-Apr-2010
Mandate

Buy Standard

Standard
EN 301 908-6 V4.2.1:2010
English language
46 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 301 908-6 V4.2.1 (2010-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 6: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive
English language
46 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 908-6 V4.1.2 (2009-12) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 6: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive
English language
46 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 908-6 V4.1.1 (2009-04) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 6: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive
English language
46 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks - Part 6: Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-6 Version 4.2.1SIST EN 301 908-6 V4.2.1:2010en01-maj-2010SIST EN 301 908-6 V4.2.1:2010SLOVENSKI
STANDARD



SIST EN 301 908-6 V4.2.1:2010



ETSI EN 301 908-6 V4.2.1 (2010-03)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Base Stations (BS), Repeaters and User Equipment (UE)for IMT-2000 Third-Generation cellular networks;Part 6: Harmonized EN for IMT-2000,CDMA TDD (UTRA TDD and E-UTRA TDD) (UE)covering the essential requirementsof article 3.2 of the R&TTE Directive SIST EN 301 908-6 V4.2.1:2010



ETSI ETSI EN 301 908-6 V4.2.1 (2010-03) 2
Reference REN/ERM-TFES-005-6 Keywords 3G, 3GPP, cellular, digital, IMT-2000, mobile, radio, regulation, TDD, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-6 V4.2.1:2010



ETSI ETSI EN 301 908-6 V4.2.1 (2010-03) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 10 3.3 Abbreviations . 11 4 Technical requirements specifications . 11 4.1 Environmental profile . 11 4.2 Conformance requirements . 12 4.2.1 Introduction. 12 4.2.2 Spectrum emission mask . 12 4.2.2.1 Definition . 12 4.2.2.1.1 3,84 Mcps TDD option . 12 4.2.2.1.2 1,28 Mcps TDD option . 12 4.2.2.1.3 7,68 Mcps TDD option . 12 4.2.2.2 Limits . 13 4.2.2.2.1 3,84 Mcps TDD option . 13 4.2.2.2.2 1,28 Mcps TDD option . 13 4.2.2.2.3 7,68 Mcps TDD option . 14 4.2.2.3 Conformance . 14 4.2.3 Transmitter spurious emissions . 14 4.2.3.1 Definition . 14 4.2.3.2 Limits . 14 4.2.3.2.1 3,84 Mcps TDD option . 14 4.2.3.2.2 1,28 Mcps TDD option . 15 4.2.3.2.3 7,68 Mcps TDD option . 15 4.2.3.3 Conformance . 16 4.2.4 Maximum output power . 16 4.2.4.1 Definition . 16 4.2.4.2 Limits . 16 4.2.4.3 Conformance . 16 4.2.5 Minimum transmit output power . 16 4.2.5.1 Definition . 16 4.2.5.2 Limits . 16 4.2.5.2.1 3,84 Mcps TDD option . 16 4.2.5.2.2 1,28 Mcps TDD option . 16 4.2.5.2.3 7,68 Mcps TDD option . 16 4.2.5.3 Conformance . 16 4.2.6 Receiver spurious emissions . 16 4.2.6.1 Definition . 16 4.2.6.2 Limits . 17 4.2.6.2.1 3,84 Mcps TDD option . 17 4.2.6.2.2 1,28 Mcps TDD option . 17 4.2.6.2.3 7,68 Mcps TDD option . 17 4.2.6.3 Conformance . 18 4.2.7 Receiver blocking characteristics . 18 4.2.7.1 Definition . 18 4.2.7.2 Limits . 18 SIST EN 301 908-6 V4.2.1:2010



ETSI ETSI EN 301 908-6 V4.2.1 (2010-03) 4 4.2.7.2.1 3,84 Mcps TDD option . 18 4.2.7.2.2 1,28 Mcps TDD option . 19 4.2.7.2.3 7,68 Mcps TDD option . 19 4.2.7.3 Conformance . 20 4.2.8 Receiver intermodulation characteristics . 20 4.2.8.1 Definition and applicability . 20 4.2.8.2 Limits . 20 4.2.8.2.1 3,84 Mcps TDD option . 20 4.2.8.2.2 1,28 Mcps TDD option . 21 4.2.8.2.3 7,68 Mcps TDD option . 21 4.2.8.3 Conformance . 21 4.2.9 Receiver spurious response . 21 4.2.9.1 Definition . 21 4.2.9.2 Limits . 22 4.2.9.2.1 3,84 Mcps TDD option . 22 4.2.9.2.2 1,28 Mcps TDD option . 22 4.2.9.2.3 7,68 Mcps TDD option . 22 4.2.9.3 Conformance . 22 4.2.10 Receiver adjacent channel selectivity . 22 4.2.10.1 Definition . 22 4.2.10.2 Limits . 23 4.2.10.2.1 3,84 Mcps TDD option . 23 4.2.10.2.2 1,28 Mcps TDD option . 23 4.2.10.2.3 7,68 Mcps TDD option . 23 4.2.10.3 Conformance . 23 4.2.11 Out-of-synchronization handling of output power . 24 4.2.11.1 Definition . 24 4.2.11.2 Limit . 24 4.2.11.2.1 3,84 Mcps TDD option . 24 4.2.11.2.2 1,28 Mcps TDD option . 25 4.2.11.2.3 7,68 Mcps TDD option . 26 4.2.11.3 Conformance . 27 4.2.12 Transmitter adjacent channel leakage power ratio . 27 4.2.12.1 Definition . 27 4.2.12.2 Limits . 27 4.2.12.2.1 3,84 Mcps TDD option . 27 4.2.12.2.2 1,28 Mcps TDD option . 28 4.2.12.2.3 7,68 Mcps TDD option . 28 4.2.12.3 Conformance . 28 5 Testing for compliance with technical requirements . 28 5.1 Environmental conditions for testing . 28 5.2 Interpretation of the measurement results . 28 5.3 Essential radio test suites . 30 5.3.1 Spectrum emission mask . 30 5.3.1.1 Method of test . 30 5.3.1.1.1 Initial conditions . 30 5.3.1.1.2 Procedure . 30 5.3.1.2 Test requirements . 31 5.3.2 Transmitter spurious emissions . 31 5.3.2.1 Method of test . 31 5.3.2.1.1 Initial conditions . 31 5.3.2.1.2 Procedure . 31 5.3.2.2 Test requirements . 31 5.3.3 Maximum output power . 31 5.3.3.1 Method of test . 31 5.3.3.1.1 Initial conditions . 31 5.3.3.1.2 Procedure . 32 5.3.3.2 Test requirements . 32 5.3.4 Minimum transmit output power . 32 5.3.4.1 Method of test . 32 5.3.4.1.1 Initial conditions . 32 SIST EN 301 908-6 V4.2.1:2010



ETSI ETSI EN 301 908-6 V4.2.1 (2010-03) 5 5.3.4.1.2 Procedure . 32 5.3.4.2 Test requirements . 33 5.3.5 Receiver spurious emissions . 33 5.3.5.1 Method of test . 33 5.3.5.1.1 Initial conditions . 33 5.3.5.1.2 Procedure . 34 5.3.5.2 Test requirements . 34 5.3.6 Receiver blocking characteristics . 34 5.3.6.1 Method of test . 34 5.3.6.1.1 Initial conditions . 34 5.3.6.1.2 Procedure . 35 5.3.6.2 Test requirements . 35 5.3.7 Receiver intermodulation characteristics . 35 5.3.7.1 Method of test . 35 5.3.7.1.1 Initial conditions . 35 5.3.7.1.2 Procedure . 36 5.3.7.2 Test requirements . 36 5.3.8 Receiver spurious response . 36 5.3.8.1 Method of test . 36 5.3.8.1.1 Initial conditions . 36 5.3.8.1.2 Procedure . 36 5.3.8.2 Test requirements . 36 5.3.9 Receiver adjacent channel selectivity . 37 5.3.9.1 Method of test . 37 5.3.9.1.1 Initial conditions . 37 5.3.9.1.2 Procedure . 37 5.3.9.2 Test requirements . 37 5.3.10 Out-of-synchronization handling of output power . 37 5.3.10.1 Method of test . 37 5.3.10.1.1 Initial conditions . 37 5.3.10.1.2 Procedure . 38 5.3.10.2 Test requirements . 39 5.3.11 Transmitter adjacent channel leakage power ratio . 39 5.3.11.1 Method of test . 39 5.3.11.1.1 Initial conditions . 39 5.3.11.1.2 Procedure . 39 5.3.11.2 Test requirements . 39 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 40 Annex B (normative): Environmental profile . 42 B.1 General . 42 B.1.1 Introduction . 42 B.1.2 Temperature . 42 B.1.3 Voltage . 42 B.1.4 Test environment . 43 Annex C (informative): The EN title in the official languages . 44 Annex D (informative): Bibliography . 45 History . 46
SIST EN 301 908-6 V4.2.1:2010



ETSI ETSI EN 301 908-6 V4.2.1 (2010-03) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (Telecommunications series) has been produced by E
...

ETSI EN 301 908-6 V4.2.1 (2010-03)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 6: Harmonized EN for IMT-2000,
CDMA TDD (UTRA TDD and E-UTRA TDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-6 V4.2.1 (2010-03)



Reference
REN/ERM-TFES-005-6
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, TDD, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-6 V4.2.1 (2010-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 10
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Spectrum emission mask . 12
4.2.2.1 Definition . 12
4.2.2.1.1 3,84 Mcps TDD option . 12
4.2.2.1.2 1,28 Mcps TDD option . 12
4.2.2.1.3 7,68 Mcps TDD option . 12
4.2.2.2 Limits . 13
4.2.2.2.1 3,84 Mcps TDD option . 13
4.2.2.2.2 1,28 Mcps TDD option . 13
4.2.2.2.3 7,68 Mcps TDD option . 14
4.2.2.3 Conformance . 14
4.2.3 Transmitter spurious emis sions . 14
4.2.3.1 Definition . 14
4.2.3.2 Limits . 14
4.2.3.2.1 3,84 Mcps TDD option . 14
4.2.3.2.2 1,28 Mcps TDD option . 15
4.2.3.2.3 7,68 Mcps TDD option . 15
4.2.3.3 Conformance . 16
4.2.4 Maximum output power . 16
4.2.4.1 Definition . 16
4.2.4.2 Limits . 16
4.2.4.3 Conformance . 16
4.2.5 Minimum transmit output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.2.1 3,84 Mcps TDD option . 16
4.2.5.2.2 1,28 Mcps TDD option . 16
4.2.5.2.3 7,68 Mcps TDD option . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver spurious emissions . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 17
4.2.6.2.1 3,84 Mcps TDD option . 17
4.2.6.2.2 1,28 Mcps TDD option . 17
4.2.6.2.3 7,68 Mcps TDD option . 17
4.2.6.3 Conformance . 18
4.2.7 Receiver blocking characteristics . 18
4.2.7.1 Definition . 18
4.2.7.2 Limits . 18
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-6 V4.2.1 (2010-03)
4.2.7.2.1 3,84 Mcps TDD option . 18
4.2.7.2.2 1,28 Mcps TDD option . 19
4.2.7.2.3 7,68 Mcps TDD option . 19
4.2.7.3 Conformance . 20
4.2.8 Receiver intermodulation characteristics . 20
4.2.8.1 Definition and applicability . 20
4.2.8.2 Limits . 20
4.2.8.2.1 3,84 Mcps TDD option . 20
4.2.8.2.2 1,28 Mcps TDD option . 21
4.2.8.2.3 7,68 Mcps TDD option . 21
4.2.8.3 Conformance . 21
4.2.9 Receiver spurious response . 21
4.2.9.1 Definition . 21
4.2.9.2 Limits . 22
4.2.9.2.1 3,84 Mcps TDD option . 22
4.2.9.2.2 1,28 Mcps TDD option . 22
4.2.9.2.3 7,68 Mcps TDD option . 22
4.2.9.3 Conformance . 22
4.2.10 Receiver adjacent channel selectivity . 22
4.2.10.1 Definition . 22
4.2.10.2 Limits . 23
4.2.10.2.1 3,84 Mcps TDD option . 23
4.2.10.2.2 1,28 Mcps TDD option . 23
4.2.10.2.3 7,68 Mcps TDD option . 23
4.2.10.3 Conformance . 23
4.2.11 Out-of-synchronization handling of output power . 24
4.2.11.1 Definition . 24
4.2.11.2 Limit . 24
4.2.11.2.1 3,84 Mcps TDD option . 24
4.2.11.2.2 1,28 Mcps TDD option . 25
4.2.11.2.3 7,68 Mcps TDD option . 26
4.2.11.3 Conformance . 27
4.2.12 Transmitter adjacent channel leakage power ratio . 27
4.2.12.1 Definition . 27
4.2.12.2 Limits . 27
4.2.12.2.1 3,84 Mcps TDD option . 27
4.2.12.2.2 1,28 Mcps TDD option . 28
4.2.12.2.3 7,68 Mcps TDD option . 28
4.2.12.3 Conformance . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Interpretation of the measurement results . 28
5.3 Essential radio test suites . 30
5.3.1 Spectrum emission mask . 30
5.3.1.1 Method of test . 30
5.3.1.1.1 Initial conditions . 30
5.3.1.1.2 Procedure . 30
5.3.1.2 Test requirements . 31
5.3.2 Transmitter spurious emis sions . 31
5.3.2.1 Method of test . 31
5.3.2.1.1 Initial conditions . 31
5.3.2.1.2 Procedure . 31
5.3.2.2 Test requirements . 31
5.3.3 Maximum output power . 31
5.3.3.1 Method of test . 31
5.3.3.1.1 Initial conditions . 31
5.3.3.1.2 Procedure . 32
5.3.3.2 Test requirements . 32
5.3.4 Minimum transmit output power . 32
5.3.4.1 Method of test . 32
5.3.4.1.1 Initial conditions . 32
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-6 V4.2.1 (2010-03)
5.3.4.1.2 Procedure . 32
5.3.4.2 Test requirements . 33
5.3.5 Receiver spurious emissions . 33
5.3.5.1 Method of test . 33
5.3.5.1.1 Initial conditions . 33
5.3.5.1.2 Procedure . 34
5.3.5.2 Test requirements . 34
5.3.6 Receiver blocking characteristics . 34
5.3.6.1 Method of test . 34
5.3.6.1.1 Initial conditions . 34
5.3.6.1.2 Procedure . 35
5.3.6.2 Test requirements . 35
5.3.7 Receiver intermodulation characteristics . 35
5.3.7.1 Method of test . 35
5.3.7.1.1 Initial conditions . 35
5.3.7.1.2 Procedure . 36
5.3.7.2 Test requirements . 36
5.3.8 Receiver spurious response . 36
5.3.8.1 Method of test . 36
5.3.8.1.1 Initial conditions . 36
5.3.8.1.2 Procedure . 36
5.3.8.2 Test requirements . 36
5.3.9 Receiver adjacent channel selectivity . 37
5.3.9.1 Method of test . 37
5.3.9.1.1 Initial conditions . 37
5.3.9.1.2 Procedure . 37
5.3.9.2 Test requirements . 37
5.3.10 Out-of-synchronization handling of output power . 37
5.3.10.1 Method of test . 37
5.3.10.1.1 Initial conditions . 37
5.3.10.1.2 Procedure . 38
5.3.10.2 Test requirements . 39
5.3.11 Transmitter adjacent channel leakage power ratio . 39
5.3.11.1 Method of test . 39
5.3.11.1.1 Initial conditions . 39
5.3.11.1.2 Procedure . 39
5.3.11.2 Test requirements . 39
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 40
Annex B (normative): Environmental profile . 42
B.1 General . 42
B.1.1 Introduction . 42
B.1.2 Temperature . 42
B.1.3 Voltage . 42
B.1.4 Test environment . 43
Annex C (informative): The EN title in the official languages . 44
Annex D (informative): Bibliography . 45
History . 46

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-6 V4.2.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmon
...

Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 6: Harmonized EN for IMT-2000,
CDMA TDD (UTRA TDD and E-UTRA TDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)



Reference
REN/ERM-TFES-005-6
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, TDD, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 10
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Spectrum emission mask . 12
4.2.2.1 Definition . 12
4.2.2.1.1 3,84 Mcps TDD option . 12
4.2.2.1.2 1,28 Mcps TDD option . 12
4.2.2.1.3 7,68 Mcps TDD option . 12
4.2.2.2 Limits . 13
4.2.2.2.1 3,84 Mcps TDD option . 13
4.2.2.2.2 1,28 Mcps TDD option . 13
4.2.2.2.3 7,68 Mcps TDD option . 14
4.2.2.3 Conformance . 14
4.2.3 Transmitter spurious emis sions . 14
4.2.3.1 Definition . 14
4.2.3.2 Limits . 14
4.2.3.2.1 3,84 Mcps TDD option . 14
4.2.3.2.2 1,28 Mcps TDD option . 15
4.2.3.2.3 7,68 Mcps TDD option . 15
4.2.3.3 Conformance . 16
4.2.4 Maximum output power . 16
4.2.4.1 Definition . 16
4.2.4.2 Limits . 16
4.2.4.3 Conformance . 16
4.2.5 Minimum transmit output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.2.1 3,84 Mcps TDD option . 16
4.2.5.2.2 1,28 Mcps TDD option . 16
4.2.5.2.3 7,68 Mcps TDD option . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver spurious emissions . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 17
4.2.6.2.1 3,84 Mcps TDD option . 17
4.2.6.2.2 1,28 Mcps TDD option . 17
4.2.6.2.3 7,68 Mcps TDD option . 17
4.2.6.3 Conformance . 18
4.2.7 Receiver blocking characteristics . 18
4.2.7.1 Definition . 18
4.2.7.2 Limits . 18
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
4.2.7.2.1 3,84 Mcps TDD option . 18
4.2.7.2.2 1,28 Mcps TDD option . 19
4.2.7.2.3 7,68 Mcps TDD option . 19
4.2.7.3 Conformance . 20
4.2.8 Receiver intermodulation characteristics . 20
4.2.8.1 Definition and applicability . 20
4.2.8.2 Limits . 20
4.2.8.2.1 3,84 Mcps TDD option . 20
4.2.8.2.2 1,28 Mcps TDD option . 21
4.2.8.2.3 7,68 Mcps TDD option . 21
4.2.8.3 Conformance . 21
4.2.9 Receiver spurious response . 21
4.2.9.1 Definition . 21
4.2.9.2 Limits . 22
4.2.9.2.1 3,84 Mcps TDD option . 22
4.2.9.2.2 1,28 Mcps TDD option . 22
4.2.9.2.3 7,68 Mcps TDD option . 22
4.2.9.3 Conformance . 22
4.2.10 Receiver adjacent channel selectivity . 22
4.2.10.1 Definition . 22
4.2.10.2 Limits . 23
4.2.10.2.1 3,84 Mcps TDD option . 23
4.2.10.2.2 1,28 Mcps TDD option . 23
4.2.10.2.3 7,68 Mcps TDD option . 23
4.2.10.3 Conformance . 23
4.2.11 Out-of-synchronization handling of output power . 24
4.2.11.1 Definition . 24
4.2.11.2 Limit . 24
4.2.11.2.1 3,84 Mcps TDD option . 24
4.2.11.2.2 1,28 Mcps TDD option . 25
4.2.11.2.3 7,68 Mcps TDD option . 26
4.2.11.3 Conformance . 27
4.2.12 Transmitter adjacent channel leakage power ratio . 27
4.2.12.1 Definition . 27
4.2.12.2 Limits . 27
4.2.12.2.1 3,84 Mcps TDD option . 27
4.2.12.2.2 1,28 Mcps TDD option . 28
4.2.12.2.3 7,68 Mcps TDD option . 28
4.2.12.3 Conformance . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Interpretation of the measurement results . 28
5.3 Essential radio test suites . 30
5.3.1 Spectrum emission mask . 30
5.3.1.1 Method of test . 30
5.3.1.1.1 Initial conditions . 30
5.3.1.1.2 Procedure . 30
5.3.1.2 Test requirements . 31
5.3.2 Transmitter spurious emis sions . 31
5.3.2.1 Method of test . 31
5.3.2.1.1 Initial conditions . 31
5.3.2.1.2 Procedure . 31
5.3.2.2 Test requirements . 31
5.3.3 Maximum output power . 31
5.3.3.1 Method of test . 31
5.3.3.1.1 Initial conditions . 31
5.3.3.1.2 Procedure . 32
5.3.3.2 Test requirements . 32
5.3.4 Minimum transmit output power . 32
5.3.4.1 Method of test . 32
5.3.4.1.1 Initial conditions . 32
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
5.3.4.1.2 Procedure . 32
5.3.4.2 Test requirements . 33
5.3.5 Receiver spurious emissions . 33
5.3.5.1 Method of test . 33
5.3.5.1.1 Initial conditions . 33
5.3.5.1.2 Procedure . 34
5.3.5.2 Test requirements . 34
5.3.6 Receiver blocking characteristics . 34
5.3.6.1 Method of test . 34
5.3.6.1.1 Initial conditions . 34
5.3.6.1.2 Procedure . 35
5.3.6.2 Test requirements . 35
5.3.7 Receiver intermodulation characteristics . 35
5.3.7.1 Method of test . 35
5.3.7.1.1 Initial conditions . 35
5.3.7.1.2 Procedure . 36
5.3.7.2 Test requirements . 36
5.3.8 Receiver spurious response . 36
5.3.8.1 Method of test . 36
5.3.8.1.1 Initial conditions . 36
5.3.8.1.2 Procedure . 36
5.3.8.2 Test requirements . 36
5.3.9 Receiver adjacent channel selectivity . 37
5.3.9.1 Method of test . 37
5.3.9.1.1 Initial conditions . 37
5.3.9.1.2 Procedure . 37
5.3.9.2 Test requirements . 37
5.3.10 Out-of-synchronization handling of output power . 37
5.3.10.1 Method of test . 37
5.3.10.1.1 Initial conditions . 37
5.3.10.1.2 Procedure . 38
5.3.10.2 Test requirements . 39
5.3.11 Transmitter adjacent channel leakage power ratio . 39
5.3.11.1 Method of test . 39
5.3.11.1.1 Initial conditions . 39
5.3.11.1.2 Procedure . 39
5.3.11.2 Test requirements . 39
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 40
Annex B (normative): Environmental profile . 42
B.1 General . 42
B.1.1 Introduction . 42
B.1.2 Temperature . 42
B.1.3 Voltage . 42
B.1.4 Test environment . 43
Annex C (informative): The EN title in the official languages . 44
Annex D (informative): Bibliography . 45
History . 46

ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended)
...

Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 6: Harmonized EN for IMT-2000,
CDMA TDD (UTRA TDD and E-UTRA TDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)



Reference
REN/ERM-TFES-005-6
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, TDD, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 10
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 12
4.2.2 Spectrum emission mask . 12
4.2.2.1 Definition . 12
4.2.2.1.1 3,84 Mcps TDD option . 12
4.2.2.1.2 1,28 Mcps TDD option . 12
4.2.2.1.3 7,68 Mcps TDD option . 12
4.2.2.2 Limits . 13
4.2.2.2.1 3,84 Mcps TDD option . 13
4.2.2.2.2 1,28 Mcps TDD option . 13
4.2.2.2.3 7,68 Mcps TDD option . 14
4.2.2.3 Conformance . 14
4.2.3 Transmitter spurious emis sions . 14
4.2.3.1 Definition . 14
4.2.3.2 Limits . 14
4.2.3.2.1 3,84 Mcps TDD option . 14
4.2.3.2.2 1,28 Mcps TDD option . 15
4.2.3.2.3 7,68 Mcps TDD option . 15
4.2.3.3 Conformance . 16
4.2.4 Maximum output power . 16
4.2.4.1 Definition . 16
4.2.4.2 Limits . 16
4.2.4.3 Conformance . 16
4.2.5 Minimum transmit output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.2.1 3,84 Mcps TDD option . 16
4.2.5.2.2 1,28 Mcps TDD option . 16
4.2.5.2.3 7,68 Mcps TDD option . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver spurious emissions . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 17
4.2.6.2.1 3,84 Mcps TDD option . 17
4.2.6.2.2 1,28 Mcps TDD option . 17
4.2.6.2.3 7,68 Mcps TDD option . 17
4.2.6.3 Conformance . 18
4.2.7 Receiver blocking characteristics . 18
4.2.7.1 Definition . 18
4.2.7.2 Limits . 18
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
4.2.7.2.1 3,84 Mcps TDD option . 18
4.2.7.2.2 1,28 Mcps TDD option . 19
4.2.7.2.3 7,68 Mcps TDD option . 19
4.2.7.3 Conformance . 20
4.2.8 Receiver intermodulation characteristics . 20
4.2.8.1 Definition and applicability . 20
4.2.8.2 Limits . 20
4.2.8.2.1 3,84 Mcps TDD option . 20
4.2.8.2.2 1,28 Mcps TDD option . 21
4.2.8.2.3 7,68 Mcps TDD option . 21
4.2.8.3 Conformance . 21
4.2.9 Receiver spurious response . 21
4.2.9.1 Definition . 21
4.2.9.2 Limits . 22
4.2.9.2.1 3,84 Mcps TDD option . 22
4.2.9.2.2 1,28 Mcps TDD option . 22
4.2.9.2.3 7,68 Mcps TDD option . 22
4.2.9.3 Conformance . 22
4.2.10 Receiver adjacent channel selectivity . 22
4.2.10.1 Definition . 22
4.2.10.2 Limits . 23
4.2.10.2.1 3,84 Mcps TDD option . 23
4.2.10.2.2 1,28 Mcps TDD option . 23
4.2.10.2.3 7,68 Mcps TDD option . 23
4.2.10.3 Conformance . 23
4.2.11 Out-of-synchronization handling of output power . 24
4.2.11.1 Definition . 24
4.2.11.2 Limit . 24
4.2.11.2.1 3,84 Mcps TDD option . 24
4.2.11.2.2 1,28 Mcps TDD option . 25
4.2.11.2.3 7,68 Mcps TDD option . 26
4.2.11.3 Conformance . 27
4.2.12 Transmitter adjacent channel leakage power ratio . 27
4.2.12.1 Definition . 27
4.2.12.2 Limits . 27
4.2.12.2.1 3,84 Mcps TDD option . 27
4.2.12.2.2 1,28 Mcps TDD option . 28
4.2.12.2.3 7,68 Mcps TDD option . 28
4.2.12.3 Conformance . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Interpretation of the measurement results . 28
5.3 Essential radio test suites . 30
5.3.1 Spectrum emission mask . 30
5.3.1.1 Method of test . 30
5.3.1.1.1 Initial conditions . 30
5.3.1.1.2 Procedure . 30
5.3.1.2 Test requirements . 31
5.3.2 Transmitter spurious emis sions . 31
5.3.2.1 Method of test . 31
5.3.2.1.1 Initial conditions . 31
5.3.2.1.2 Procedure . 31
5.3.2.2 Test requirements . 31
5.3.3 Maximum output power . 31
5.3.3.1 Method of test . 31
5.3.3.1.1 Initial conditions . 31
5.3.3.1.2 Procedure . 32
5.3.3.2 Test requirements . 32
5.3.4 Minimum transmit output power . 32
5.3.4.1 Method of test . 32
5.3.4.1.1 Initial conditions . 32
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
5.3.4.1.2 Procedure . 32
5.3.4.2 Test requirements . 33
5.3.5 Receiver spurious emissions . 33
5.3.5.1 Method of test . 33
5.3.5.1.1 Initial conditions . 33
5.3.5.1.2 Procedure . 34
5.3.5.2 Test requirements . 34
5.3.6 Receiver blocking characteristics . 34
5.3.6.1 Method of test . 34
5.3.6.1.1 Initial conditions . 34
5.3.6.1.2 Procedure . 34
5.3.6.2 Test requirements . 35
5.3.7 Receiver intermodulation characteristics . 35
5.3.7.1 Method of test . 35
5.3.7.1.1 Initial conditions . 35
5.3.7.1.2 Procedure . 35
5.3.7.2 Test requirements . 36
5.3.8 Receiver spurious response . 36
5.3.8.1 Method of test . 36
5.3.8.1.1 Initial conditions . 36
5.3.8.1.2 Procedure . 36
5.3.8.2 Test requirements . 36
5.3.9 Receiver adjacent channel selectivity . 36
5.3.9.1 Method of test . 36
5.3.9.1.1 Initial conditions . 36
5.3.9.1.2 Procedure . 37
5.3.9.2 Test requirements . 37
5.3.10 Out-of-synchronization handling of output power . 37
5.3.10.1 Method of test . 37
5.3.10.1.1 Initial conditions . 37
5.3.10.1.2 Procedure . 37
5.3.10.2 Test requirements . 38
5.3.11 Transmitter adjacent channel leakage power ratio . 38
5.3.11.1 Method of test . 38
5.3.11.1.1 Initial conditions . 38
5.3.11.1.2 Procedure . 39
5.3.11.2 Test requirements . 39
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 40
Annex B (normative): Environmental profile . 42
B.1 General . 42
B.1.1 Introduction . 42
B.1.2 Temperature . 42
B.1.3 Voltage . 42
B.1.4 Test environment . 43
Annex C (informative): The EN title in the official languages . 44
Annex D (informative): Bibliography . 45
History . 46

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedur
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.