SIST EN ISO 8673:2002

Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and B (ISO 8673:1999)

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months because //FV has been missed (Res BT C 243/1999) (CC/991125)

Sechskantmuttern, Typ 1, mit metrischem Feingewinde -Produktklassen A und B (ISO 8673:1999)

Diese Internationale Norm legt Eigenschaften von Sechskantmuttern, Typ 1, mit metrischem Feingewinde mit Gewinde-Nenndurchmessern d von 8 mm bis 64 mm fest. Für die Gewinde-Nenndurchmesser d <= 16 mm gilt Produktklasse A und für die Gewinde-Nenndurchmesser d > 16 mm Produktklasse B. Falls in besonderen Fällen andere Festlegungen als die in dieser Norm aufgeführten benötigt werden, sollten diese den entsprechenden ISO-Normen entnommen werden, z.B. ISO 724, ISO 898-6, ISO 965-1, ISO 3506-2 und ISO 4759-1. Sechskantmuttern mit Regelgewinde, Typ 1, nach ISO 4032 sollten bevorzugt werden.

Ecrous hexagonaux, style 1, a filetage métrique a pas fin -Grades A et B (ISO 8673:1999)

La présente Norme internationale spécifie les caractéristiques des écrous hexagonaux de style 1, à filetage métrique à pas fin, de diamètre nominal de filetage, d, de 8 mm à 64 mm inclus, de grade A pour les diamètres d < ou = 16 mm et de grade B pour les diamètres d > 16 mm. Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme internationale sont requises, il est recommandé de les prendre dans les Normes internationales existantes, par exemple ISO 724, ISO 898-6, ISO 965-1, ISO 3506-2 et ISO 4759-1. Les écrous hexagonaux de style 1 à pas gros qui font l'objet de l'ISO 4032 constituent des produits à choisir de façon préférentielle. NOTE: Pour les écrous hexagonaux de style 2 à filetage métrique à pas fin, voir l'ISO 8674.

Šestrobe matice, tip 1, z metrskim drobnim navojem - Razreda izdelave A in B (ISO 8673:1999)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2002
• Withdrawal Date: 25-Jun-2013
• ICS: 21.040.10 - Metric screw threads
• ICS: 21.060.20 - Nuts
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 21-Jun-2013
• Due Date: 14-Jul-2013
• Completion Date: 26-Jun-2013
• Ref Project: EN ISO 8673:2000 - Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and B (ISO 8673:1999)

Relations

• Replaced By: SIST EN ISO 8673:2013 - Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and B (ISO 8673:2012)
• Effective Date: 01-Jul-2013
• Replaces: SIST EN 28673:1996 - Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and B (ISO 8673:1988)
• Effective Date: 01-Jul-2002
• Revised: SIST EN ISO 8673:2013 - Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and B (ISO 8673:2012)
• Effective Date: 07-Mar-2012

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8673:2002
01-julij-2002
1DGRPHãþD
SIST EN 28673:1996
Šestrobe matice, tip 1, z metrskim drobnim navojem - Razreda izdelave A in B (ISO
8673:1999)
Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and B (ISO
8673:1999)
Sechskantmuttern, Typ 1, mit metrischem Feingewinde -Produktklassen A und B (ISO
8673:1999)
Ecrous hexagonaux, style 1, a filetage métrique a pas fin -Grades A et B (ISO
8673:1999)
Ta slovenski standard je istoveten z: EN ISO 8673:2000
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.20 Matice Nuts
SIST EN ISO 8673:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8673:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 8673:2002

---------------------- Page: 3 ----------------------

SIST EN ISO 8673:2002

---------------------- Page: 4 ----------------------

SIST EN ISO 8673:2002

---------------------- Page: 5 ----------------------

SIST EN ISO 8673:2002

---------------------- Page: 6 ----------------------

SIST EN ISO 8673:2002
INTERNATIONAL ISO
STANDARD 8673
Second edition
1999-08-15
Hexagon nuts, style 1, with metric fine pitch
thread — Product grades A and B
Écrous hexagonaux, style 1, à filetage métrique à pas fin — Grades A et B
A
Reference number
ISO 8673:1999(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 8673:2002
ISO 8673:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 8673 was prepared by Technical Committee ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 8673:1988) which has been technically revised.
©  ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 8673:2002
© ISO
ISO 8673:1999(E)
Introduction
This International Standard is part of the complete ISO product standard series on external hexagon drive
fasteners. The series comprises:
a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);
d) hexagon bolts with flange (ISO 4162 and ISO 15071);
e) hexagon nuts with flange (ISO 4161 and ISO 10663);
f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).
iii

---------------------- Page: 9 ----------------------

SIST EN ISO 8673:2002

---------------------- Page: 10 ----------------------

SIST EN ISO 8673:2002
INTERNATIONAL STANDARD  © ISO ISO 8673:1999(E)
Hexagon nuts, style 1, with metric fine pitch thread —
Product grades A and B
1 Scope
This International Standard specifies the characteristics of hexagon nuts, style 1, with metric fine pitch thread, with
nominal thread diameters d from 8 mm up to and including 64 mm, with product grade A for sizes d up to and including
16 mm and product grade B for sizes d over 16 mm.
If, in special cases, specifications other than those listed in this International Standard are required, they should be
selected from existing International Standards, for example ISO 724, ISO 898-6, ISO 965-1, ISO 3506-2 and
ISO 4759-1.
Coarse thread hexagon nuts, style 1, according to ISO 4032 should be the first choice.
NOTE For hexagon nuts, style 2, with fine pitch thread, see ISO 8674.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
ISO 724:1993, ISO general-purpose metric screw threads — Basic dimensions.
ISO 898-6:1994, Mechanical properties of fasteners — Part 6: Nuts with specified proof load values — Fine pitch
thread.
ISO 965-1:1998, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data.
1)
ISO 3269:— , Fasteners — Acceptance inspection.
ISO 3506-2:1997, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 2: Nuts.
ISO 4042:1999, Fasteners — Electroplated coatings.
2)
ISO 4759-1:— , Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C.
ISO 6157-2:1995, Fasteners — Surface discontinuities — Part 2: Nuts.
ISO 8839:1986, Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals.

1)
To be published. (Revision of ISO 3269:1988)
2)
To be published. (Revision of ISO 4759-1:1978)
1

---------------------- Page: 11 ----------------------

SIST EN ISO 8673:2002
© ISO
ISO 8673:1999(E)
ISO 8992:1986,
Fastener
...