SIST EN ISO 17235:2015
(Main)Leather - Physical and mechanical tests - Determination of softness (ISO 17235:2015)
Leather - Physical and mechanical tests - Determination of softness (ISO 17235:2015)
This International Standard specifies a non-destructive method for determining the softness of leather.
It is applicable to all non-rigid leathers, e.g. shoe upper leather, upholstery leather, leathergoods leather,
and apparel leather.
Leder - Physikalische und mechanische Prüfungen - Bestimmung der Weichheit (ISO 17235:2015)
Cuir - Essais physiques et mécaniques - Détermination de la souplesse (ISO 17235:2015)
L'ISO 17235:2015 spécifie une méthode d'essai non destructive pour déterminer la souplesse du cuir. Elle s'applique à tous les cuirs non rigides, par exemple les cuirs à dessus de chaussure, les cuirs d'ameublement, les cuirs d'articles de maroquinerie et les cuirs pour habillement.
Usnje - Fizikalni in mehanski preskusi - Ugotavljanje mehkosti (ISO 17235:2015)
Ta mednarodni standard določa nedestruktivno preskusno metodo za ugotavljanje mehkosti usnja. Uporablja se za vse prožne vrste usnja, npr. usnje, ki se uporablja za zgornji del čevlja, tapetništvo, usnjene izdelke in obleke.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 17235:2015
01-december-2015
1DGRPHãþD
SIST EN ISO 17235:2012
Usnje - Fizikalni in mehanski preskusi - Ugotavljanje mehkosti (ISO 17235:2015)
Leather - Physical and mechanical tests - Determination of softness (ISO 17235:2015)
Leder - Physikalische und mechanische Prüfungen - Bestimmung der Weichheit (ISO
17235:2015)
Cuir - Essais physiques et mécaniques - Détermination de la souplesse (ISO
17235:2015)
Ta slovenski standard je istoveten z: EN ISO 17235:2015
ICS:
59.140.30 Usnje in krzno Leather and furs
SIST EN ISO 17235:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 17235:2015
---------------------- Page: 2 ----------------------
SIST EN ISO 17235:2015
EN ISO 17235
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2015
EUROPÄISCHE NORM
ICS 59.140.30 Supersedes EN ISO 17235:2011
English Version
Leather - Physical and mechanical tests - Determination of
softness (ISO 17235:2015)
Cuir - Essais physiques et mécaniques - Détermination Leder - Physikalische und mechanische Prüfungen -
de la souplesse (ISO 17235:2015) Bestimmung der Weichheit (ISO 17235:2015)
This European Standard was approved by CEN on 8 August 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17235:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 17235:2015
EN ISO 17235:2015 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 17235:2015
EN ISO 17235:2015 (E)
European foreword
This document (EN ISO 17235:2015) has been prepared by Technical Committee CEN/TC 289
“Leather”, the secretariat of which is held by UNI, in collaboration with Technical Committee IULTCS
“International Union of Leather Technologists and Chemists Societies”.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall
be withdrawn at the latest by March 2016.
This document supersedes EN ISO 17235:2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17235:2015 has been approved by CEN as EN ISO 17235:2015 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 17235:2015
---------------------- Page: 6 ----------------------
SIST EN ISO 17235:2015
INTERNATIONAL ISO
STANDARD 17235
IULTCS/IUP 36
Third edition
2015-09-01
Leather — Physical and mechanical
tests — Determination of softness
Cuir — Essais physiques et mécaniques — Détermination de la
souplesse
Reference numbers
ISO 17235:2015(E)
IULTCS/IUP 36:2015(E)
©
ISO 2015
---------------------- Page: 7 ----------------------
SIST EN ISO 17235:2015
ISO 17235:2015(E)
IULTCS/IUP 36:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 17235:2015
ISO 17235:2015(E)
IULTCS/IUP 36:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
5 Sampling and sample preparation . 2
6 Procedure. 2
7 Test report . 3
Annex A (informative) Source of apparatus . 4
© ISO 2015 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 17235:2015
ISO 17235:2015(E)
IULTCS/IUP 36:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO coll
...
SLOVENSKI STANDARD
kSIST FprEN ISO 17235:2015
01-julij-2015
Usnje - Fizikalni in mehanski preskusi - Ugotavljanje mehkosti (ISO/FDIS
17235:2015)
Leather - Physical and mechanical tests - Determination of softness (ISO/FDIS
17235:2015)
Leder - Physikalische und mechanische Prüfungen - Bestimmung der Weichheit
(ISO/FDIS 17235:2015)
Cuir - Essais physiques et mécaniques - Détermination de la souplesse (ISO/FDIS
17235:2015)
Ta slovenski standard je istoveten z: FprEN ISO 17235 rev
ICS:
59.140.30 Usnje in krzno Leather and furs
kSIST FprEN ISO 17235:2015 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST FprEN ISO 17235:2015
---------------------- Page: 2 ----------------------
kSIST FprEN ISO 17235:2015
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 17235
IULTCS/IUP 36
IULTCS
Leather — Physical and mechanical
Voting begins
on: 201 5-05-07
tests — Determination of softness
Voting terminates
Cuir — Essais physiques et mécaniques — Détermination de la souplesse
on: 201 5-07-07
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference numbers
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 17235:2015(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
IULTCS/IUP 36:2015(E)
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2015
---------------------- Page: 3 ----------------------
kSIST FprEN ISO 17235:2015
ISO/FDIS 17235:2015(E)
IULTCS/IUP 36:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
kSIST FprEN ISO 17235:2015
ISO/FDIS 17235:2015(E)
IULTCS/IUP 36:2015(E)
ISO/CEN PARALLEL PROCESSING
This final draft has been developed within the European Committee for Standardization (CEN), and processed
under the CEN-lead mode of collaboration as defined in the Vienna Agreement. The final draft was established
on the basis of comments received during a parallel enquiry on the draft.
This final draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel two-
month approval vote in ISO and two month formal vote in CEN.
Positive votes shall not be accompanied by comments.
Negative votes shall be accompanied by the relevant technical reasons.
© ISO 2015 – All rights reserved iii
---------------------- Page: 5 ----------------------
kSIST FprEN ISO 17235:2015
ISO/FDIS 17235:2015(E)
IULTCS/IUP 36:2015(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
5 Sampling and sample preparation . 2
6 Procedure. 2
7 Test report . 3
Annex A (informative) Source of apparatus . 4
iv © ISO 2015 – All rights reserved
---------------------- Page: 6 ----------------------
kSIST FprEN ISO 17235:2015
ISO/FDIS 17235:2015(E)
IULTCS/IUP 36:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information.
IULTCS, originally
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.