iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 846-11:2001

(Main)

Methods of test for ancillary components for masonry - Part 11: Determination of dimensions and bow of lintels

Methods of test for ancillary components for masonry - Part 11: Determination of dimensions and bow of lintels

This European Standard specifies methods for determining the dimensions and straightness or bow of single span, single, combined or the prefabricated component of composite lintels conforming with prEN 845-2:1992.

Prüfverfahren für Ergänzungsbauteile für Mauerwerk - Teil 11: Bestimmung der Maße und der Überhöhung von Stürzen

Diese Europäische Norm legt Verfahren zur Bestimmung der Maße und der Überhöhung von einfeldrigen, vorgefertigten und zusammengesetzten Stürzen oder den vorgefertigten Teil von bauseits zu ergänzenden Stürzen nach prEN 845-2:1992 fest.

Méthodes d'essai des composants accessoires de maçonnerie - Partie 11: Détermination des dimensions et de la rectitude ou de la courbure des linteaux

La présente Norme Européenne spécifie les méthodes de détermination des dimensions et de la rectitude ou de la courbure des éléments de linteaux a portée simple, concernant les linteaux simples, les linteaux pour murs doubles ou la partie préfabriquée des linteaux composites conformes au prEN 845-2:1992.

Metode preskušanja dodatnih komponent zidovine - 11. del: Ugotavljanje mer in ukrivljenosti preklad

General Information

Status
Published
Publication Date
31-Jan-2001
ICS
91.080.30 - Masonry
Technical Committee
CAA - Mineral binders and masonry
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Feb-2001
Due Date
01-Feb-2001
Completion Date
01-Feb-2001
Directive
89/106/EEC - Construction products
Mandate
M/116 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on masonry and related products
Ref Project
EN 846-11:2000 - Methods of test for ancillary components for masonry - Part 11: Determination of dimensions and bow of lintels

Buy Standard

EN 846-11:2001EN 846-11:2001
PreviousNext
Standard
EN 846-11:2001
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 846-11:2001
01-februar-2001
Metode preskušanja dodatnih komponent zidovine - 11. del: Ugotavljanje mer in
ukrivljenosti preklad
Methods of test for ancillary components for masonry - Part 11: Determination of
dimensions and bow of lintels
Prüfverfahren für Ergänzungsbauteile für Mauerwerk - Teil 11: Bestimmung der Maße
und der Überhöhung von Stürzen
Méthodes d'essai des composants accessoires de maçonnerie - Partie 11:
Détermination des dimensions et de la rectitude ou de la courbure des linteaux
Ta slovenski standard je istoveten z: EN 846-11:2000
ICS:
91.080.30 Zidane konstrukcije Masonry
SIST EN 846-11:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1745:2020(Main)
Masonry and masonry products - Methods for determining thermal properties
EN 1745:2020

This document specifies methods for the determination of thermal properties of masonry and masonry products.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1052-2:2016/AC:2017(Corrigendum)
Methods of test for masonry - Part 2: Determination of flexural strength
EN 1052-2:2016/AC:2017

TC - clarification of Units

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 16886:2017(Main)
Guidance on the application of statistical methods for determining the properties of masonry products
CEN/TR 16886:2016

In the masonry unit standards and in national legislation, some properties need to be declared based on a certain fractile and confidence level. To demonstrate compliance with that a statistical tool can be used.
The purpose of this Technical Report is to exemplify how a statistical tool can be used in practice. This document should not contradict nor extend the scope of the work and role of a Notified Body, nor impose additional burdens on the manufacturer, beyond those laid down in the Construction Products Regulation and the product standards.
Mechanical and other properties of building materials and components are in the report described by random variables with a certain type of probability distribution. The popular normal distribution (Laplace-Gauss distribution) is given in Annex A. Normal distribution may be used to approximate many actual symmetrical distributions. When a remarkable asymmetry is observed, then another type of distribution reflecting this asymmetry should be considered, leading to a more complex method to demonstrate compliance with the product standard. More information on the normality test of Shapiro-Wilk is given in Annex D.

  • Technical report
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 845-2:2013+A1:2016(Main)
Specification for ancillary components for masonry - Part 2: Lintels
EN 845-2:2013+A1:2016

This European Standard specifies requirements for prefabricated lintels for maximum spans of 4,5 m and made from steel, autoclaved aerated concrete, manufactured stone, concrete, fired clay units, calcium silicate units, natural stone units, or a combination of these materials. Concrete and steel beams conforming to EN 1090-1, EN 12602 and EN 13225, as appropriate, are not covered by this standard.
Prefabricated lintels can be either complete lintels or the prefabricated part of a composite lintel.
This European Standard is not applicable to:
a)   lintels completely made on site;
b)   lintels of which the tensile parts are made on site;
c)   timber lintels;
d)   natural stone lintels, not reinforced.
Linear components spanning clear openings greater than 4,5 m in masonry walls and linear components intended for use independently in a structural role (e.g. beams) are not covered by this standard.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 845-3:2013+A1:2016(Main)
Specification for ancillary components for masonry - Part 3: Bed joint reinforcement of steel meshwork
EN 845-3:2013+A1:2016

This European Standard specifies the requirements for masonry bed joint reinforcement for structural use (see 5.2.1) and for non-structural use (see 5.2.2).
Where products are intended for use in cavity wall construction, this European Standard covers only the performance of the meshwork as reinforcement in bed joints and not its performance as wall ties across the cavity.
This European Standard is not applicable to:
a)   products in the form of individual bars or rods;
b)   products formed from materials other than specified grades of austenitic stainless steel, austenitic ferritic stainless steel, zinc pre-coated steel sheet or zinc coated steel wire with or without organic coating.
NOTE   Annex ZA refers only to welded wire meshwork intended for structural use referred to in 5.2.1 as there are no known regulated requirements for products of this family for non-structural use.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 845-1:2013+A1:2016(Main)
Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets
EN 845-1:2013+A1:2016

This European Standard specifies requirements for wall ties, tension straps, hangers and brackets for interconnecting masonry and for connecting masonry to other parts of works and buildings including walls, floors, beams, and columns. Where anchors or fasteners are supplied or specified as part of an ancillary component, the requirements including performance requirements apply to the complete product.
This European Standard is not applicable to:
a)   anchors and fasteners other than as part of an ancillary component;
b)   shelf angles;
c)   wall starter plates for tying into existing walls;
d)   products formed from materials other than:
1)   austenitic stainless steel (molybdenum chrome nickel alloys or chrome nickel alloys);
2)   austenitic ferritic stainless steel;
3)   ferritic stainless steel;
4)   copper;
5)   phosphor bronze;
6)   aluminium bronze;
7)   zinc-coated-steel with or without organic coating;
8)   polypropylene;
9)   polyamide (for expansion plugs only).
NOTE   The resistance to fire performance of the products included herein cannot be assessed separately from the masonry element of which they are part and is therefore not covered under the scope of this part of this European Standard.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 846-9:2016(Main)
Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels
EN 846-9:2016

This European Standard specifies methods for determining the flexural and shear resistances and load deflection characteristics of single span, single or composite lintels used for supporting uniformly distributed loads over openings in masonry construction.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1052-2:2016(Main)
Methods of test for masonry - Part 2: Determination of flexural strength
EN 1052-2:2016

This European standard specifies a method for determining the flexural strength of small masonry specimens for the two principal axes of loading. Guidance is given on the preparation of the specimens, the conditioning required before testing, the testing machine, the method of test, the method of calculation and the contents of the test report.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 846-14:2012(Main)
Methods of test for ancillary components for masonry - Part 14: Determination of the initial shear strength between the prefabricated part of a composite lintel and the masonry above it
EN 846-14:2012

This European Standard specifies a method for determining the in plane initial shear strength of the horizontal bed joint between the prefabricated part of a composite lintel and the masonry above it, using a specimen tested in shear. Guidance is given on the preparation of the specimens, the conditioning required before testing, the testing machine, the method of test, the method of calculation and the contents of the test report. The method corresponds with the method described in EN 1052-3:2003+A1:2006. Guidance is given where the method deviates from EN 1052-3. Therefore, each section of EN 1052-3 is repeated given the necessary changes.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 846-5:2012(Main)
Methods of test for ancillary components for masonry - Part 5: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (couplet test)
EN 846-5:2012

This European Standard specifies the couplet method for determining the tensile and compressive load capacity and load displacement characteristics of wall ties embedded in mortar joints. The test is intended for ties used for connecting together two leaves of masonry and for the mortar bedded end of ties for connecting masonry leaves to other structures.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day